• Korean Journal of Agricultural and Forest Meteorology
• /
• v.24 no.2
• /
• pp.124-132
• /
• 2022

This study was aimed to visualize the spatial distribution of PM₁₀ data measured at non-uniformly distributed observation sites in South Korea. Different spatial interpolation methods were applied to irregularly distributed PM₁₀ observation data from January, 2019, when the concentration was the highest and in July, 2019, when the concentration was the lowest. Four interpolation methods with different parameters were used: Inverse Distance Weighted (IDW), Ordinary Kriging (OK), radial base function, and scattered interpolation. Six cases were cross-validated and the normalized root-mean-square error for each case was compared. The results showed that IDW using smoothing-related factors was the most appropriate method, while the OK method was least appropriate. Our results are expected to help users select the proper spatial interpolation method for PM₁₀ data analysis with comparative reliability and effectiveness.

• Journal of the Korean earth science society
• /
• v.43 no.3
• /
• pp.351-366
• /
• 2022

We investigated the kinematic activity of the Type II Seyfert galaxy Mrk 1 based on H𝛽 and [O III] 5007 extracted from the MR 1 grism spectra observed with the OASIS attached to the CFHT 3.6 m telescope. The [O III] forbidden Gaussian line profiles exhibited asymmetric features with an excess of the blue component: (1) strongest at a distance of about 960 pc from the galaxy center, and (2) a wider line width of about ~900 km s^-1 in the NS direction of the center. The velocity distributions in the spectral images showed blue or approaching flow motion in the NE zone, while receding in the SW zone, implying the counter-clockwise rotation. The radial velocity data showed that the center of the AGN region appears to be blocked by gas-dust approaching toward the Earth.

• Wind and Structures
• /
• v.36 no.3
• /
• pp.161-174
• /
• 2023

The analytical model of tornado vortices plays an essential role in tornado wind description and tornado-resistant design of civil structures. However, there is still a lack of guidance for the selection and application of tornado analytical models since they are different from each other. For single-cell tornado vortices, this study conducts a comparative study on the velocity characteristics of the analytical models based on numerically simulated tornado-like vortices (TLV). The single-cell stage TLV is first generated by Large-eddy simulations (LES). The spatial distribution of the three-dimensional mean velocity of the typical analytical tornado models is then investigated by comparison to the TLV with different swirl ratios. Finally, key parameters are given as functions of swirl ratio for the direct application of analytical tornado models to generate full-scale tornado wind field. Results show that the height of the maximum radial mean velocity is more appropriate to be defined as the boundary layer thickness of the TLV than the height of the maximum tangential mean velocity. The TLV velocity within the boundary layer can be well estimated by the analytical model. Simple fitted results show that the full-scale maximum radial and tangential mean velocity increase linearly with the swirl ratio, while the radius and height corresponding to the position of these two velocities decrease non-linearly with the swirl ratio.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.3
• /
• pp.215-223
• /
• 2005

An electrical machine for a high-speed flywheel for energy storage in large hybrid electric vehicles is described. Design choices for the machine are motivated: it is a radial-flux external-rotor permanent-magnet synchronous machine without slots in the stator iron and with a shielding cylinder. An analytical model of the machine is briefly introduced whereafter optimization of the machine is discussed. Three optimization criteria were chosen: (1) torque; (2) total stator losses and (3) induced eddy current loss on the rotor. The influence of the following optimization variables on these criteria is investigated: (1) permanent-magnet array; (2) winding distribution and (3) machine geometry. The paper shows that an analytical model of the machine is very useful in optimization.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1309-1312
• /
• 2002

The electric power network paralleled with wind turbine generator may have the negative impacts on the protection, operation, and management caused by the operation of wind turbine generator. Therefore, it is necessary to investigate the operating characteristic of wind turbine generator. This paper describes model of a squirrel-cage type wind turbine induction generator and the soft cut-in connection method for reducing the transient state on power network, and simulates various cases of wind turbine operations. The radial distribution network of IEEE 13-bus are modeled and tested by PSCAD/EMTDC.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2603-2608
• /
• 2007

Flows in the centrifugal compressor volute with circular cross section are numerically investigated. The computational grid for the calculation utilized a multi-block arrangement to form a butterfly grid and flow calculations are performed using commercial CFD software, CFX-TASCflow. The centrifugal compressor of this study has axial diffuser after radial diffuser because of the shape of inlet duct and installation constraints. Due to this feature the swirling flow pattern is different from the other investigations. The flow inside volute is very complex and three dimensional with strong vortex and recirculation through volute tongue. The calculation results show circumferential variations of the swirl and through flow velocity and pressure distribution. The mechanism deciding flow structure is explained by considering the force balance in volute cross section. And static pressure recovery and total pressure loss are estimated from the calculated results and compared with Japikse model.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1927-1929
• /
• 2004

현재 널리 쓰이는 고밀도 플라즈마 장치의 식각 시뮬레이션은 식각 패턴으로는 level set method이며 바이어스가 인가된 sheath model로는 Riley sheath model 이 보편적으로 받아들여지고 있다. 이러한 식각 시뮬레이션은 RF(Radio Frequency) sheath로부터 가속된 이온이 단위 입체각당 특정 지점에 이온 플럭스 분포함수, 이온 에너지 분포함수와, 중성종의 수송모델로 etch rate을 결정하는 과정과 level set method을 이용하여 식각 형태를 계산하는 과정으로 구성되어있다. 본 연구는 식각 형태 계산 이전의 단계로서 $Ar^+,\;Cl_2{^+},\;Cl^+$이온의 유동속도와 밀도를 장치의 radial방향으로 불균일하게 가정하였고, 가정한 값으로 이온 플럭스와 에너지 플럭스에 대한 영향을 알아보았다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.153.1-153.1
• /
• 2010

가스 하이드레이트는 낮은 온도와 높은 압력에서 물과 천연가스 분자가 물리적으로 안정한 결합을 하고 있는 결정질의 화합물이다. 현재 130개 이상의 가스분자들이 물분자와 결합하여서 Clathrate 하이드레이트를 형성하는 것으로 보고 되어 있다. 수소의 경우 하이드레이트를 형성하기 위해서 약 200MPa 이상의 높은 압력이 필요하다. TBAB는 semi-clathrate 하이드레이트를 형성하는 첨가제로 알려져 있으며 수소 하이드레이트의 형성 압력을 완화시키기 위한 촉진제로서 많은 연구가 수행되고 있다. Wataru Shimada는 XRD 패턴을 사용하여 semi-clathrate 하이드레이트의 특수한 결정 모델을 분석하였다. 이 모델의 경우, 대기압 하에서 TBAB와 물분자의 화학 양론적 비를 1:38로 제시하였다. 이는 처음으로 TBAB 하이드레이트 결정구조를 밝혀냈지만, 분자 동역학적 부문에서는 그 데이터가 정확히 정의 되지 않았다. 본 연구는 Wataru Shimada 모델을 수소 TBAB 하이드레이이트의 분자 동역학 연구에 적용시켰으며, 실험에서 나온 데이터를 바탕으로 RDF(Radial Distribution Function)와 MSD(Mean Square Displacement)를 측정했다.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.909-914
• /
• 2001

Fluid properties which are most commonly used to evaluate spray atomization characteristics, are important because they affect velocity and size distribution of droplets. The purpose of this study was to incorporate the significant characteristics in atomization process of industrial etching spray and how each of them affects the design of precise pressure-swirl nozzles. The experiment was carried out with different viscosity and density of fluid. The macro characteristics of liquid spray, such as the spray angle and shape were captured by PMAS and the micro characteristics of liquid spray, such as droplet size and velocity were obtained by PDA. The mean velocity and SMD of droplets were measured along axial and radial direction. It was found that the higher viscosity and density resulted in the larger SMD and the lower mean velocity of droplets.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.795-800
• /
• 2001

In this study, a program to design a multi-stage axial compressor is developed wi th mean-line analysis and vortex methods. In a preliminary design stage, a method. to design in a short time is needed and mean-line analysis is usually used for this purpose. Arbitrary pressure ratio and reaction can be assigned to generate overall geometry and several vortex methods are adopted to consider the radial distribution of velocity and reaction. The variation of performance, when we use free vortex, forced vortex, and exponential method, is compared and discussed.