• Journal of Electrical Engineering and Technology
• /
• 제12권1호
• /
• pp.161-172
• /
• 2017

In the paper, a hybrid technique is proposed for detecting the location and capacity of distributed generation (DG) sources like wind and photovoltaic (PV) in power system. The novelty of the proposed method is the combined performance of both the Biography Based Optimization (BBO) and Particle Swarm Optimization (PSO) techniques. The mentioned techniques are the optimization techniques, which are used for optimizing the optimum location and capacity of the DG sources for radial distribution network. Initially, the Artificial Neural Network (ANN) is applied to obtain the available capacity of DG sources like wind and PV for 24 hours. The BBO algorithm requires radial distribution network voltage, real and power loss for determining the optimum location and capacity of the DG. Here, the BBO input parameters are classified into sub parameters and allowed as the PSO algorithm optimization process. The PSO synthesis the problem and develops the sub solution with the help of sub parameters. The BBO migration and mutation process is applied for the sub solution of PSO for identifying the optimum location and capacity of DG. For the analysis of the proposed method, the test case is considered. The IEEE standard bench mark 33 bus system is utilized for analyzing the effectiveness of the proposed method. Then the proposed technique is implemented in the MATLAB/simulink platform and the effectiveness is analyzed by comparing it with the BBO and PSO techniques. The comparison results demonstrate the superiority of the proposed approach and confirm its potential to solve the problem.

• Applied Microscopy
• /
• 제33권3호
• /
• pp.195-204
• /
• 2003

Imaging plate에 기록된 전자회절 자료의 면간 거리 분석과 상동정시 나타나는 오차 요인들을 고찰하고 실험적인 보정방법을 도출하였다. 각각의 회절방향에 대한 radial intensity distribution plot과 실험적으로 도출된 면간 거리 보정식에 의해 전자회절 자료의 디지털 이미지에서 면간 거리 측정오차는 약 0.5%로 낮아짐을 알 수 있었다. Al 표준시료를 이용하여 imaging plate에 기록된 전자회절 자료의 면간 거리 편차 경향을 분석한 후 [001] gibbsite 시편에 동일한 실험적 보정을 수행하여 120분간의 전자빔 조사로부터 형성된 여러 전이 상들에 대한 면간 거리 측정 및 상 동정을 보다 정밀히 수행할 수 있었다. 그 결과, gibbsite로부터 형성된 주요 전이상들은 ${\chi}$-알루미나, ${\gamma}$-알루미나, ${\sigma}$-알루미나로 구성됨을 명확하게 동정할 수 있었다.

• 대한수의학회지
• /
• 제41권4호
• /
• pp.455-465
• /
• 2001

Glial fibrillary acidic protein(GFAP) is one of the intermediate filaments, and used as an astrocyte detection marker. GFAP distribution has been studied on the fetal, neonatal and aged brains. In this study, the GFAP immunoreactive cell localization and distribution in the fetal (30, 45, 60, 90, 105 and 120 days of gestation) and neonate spinal cords of Korean native goat were investigated by immunohistochemistry. Nonpolar radial glial cells initiated to appear at 45 days of gestation. GFAP-immunoreactive processes were extended from central canal to pia matter. Bipolar immumoreactive cells were transformed to monopolar and multipolar immunoreactive cells at 45 days of gestation. Multipolar astrocytes of 60 days of gestation were found within white and gray matters of spinal cord. The number of GFAP-immunoreactive cells were gradually decreased from 90 days of gestation until newborn neonate. The intensity of GFAP immunoreactivity was gradually decreased from 95 days of gestation until newborn neonate. These results suggest that the radial glial cells within the gray and white matters of spinal cord are very fast developed.

• 한국유통학회지:유통연구
• /
• 제10권3호
• /
• pp.1-14
• /
• 2005

성공적인 공급사슬관리에 있어 성과에 따른 지속적 협업 통제는 매우 중요하다. 본 연구에서는 기계학습 알고리즘인 SVM(Support Vector Machiness)을 이용해 균형성과표에 기반한 공급사슬관리 성과에 따른 지속적 협업 통제 모델을 개발하였다. 우리는 지속적 협업 통제모델 개발에 있어 108명의 전문가를 상대로 실증조사를 수행하였다. 본 연구 수행에 있어 4가지 형태의 SVM 커늘 (1) linear, (2) polynomail, (3) Radial Basis Function(RBF), (4) sigmoid kernel을 이용해 공급사슬관리 지속적 협업 예측 정확도를 비교하였다. SVM 커늘 4가지 중 linear kernel의 예측성과가 가장 좋았다. 그리고 본 연구에서는 SVM linear kernel의 예측성과를 ANN(Artificial Neural Network)의 예측성과와 비교하였다. 분석결과 SVM linear kernel이 공급사슬관리에 있어 지속적 협업 예측에 우수한 예측성과를 보여주는 것을 발견하였다. 이러한 곁과는 SVM linear kernel이 공급사슬관리의 지속적 협업 예측 통제에 있어 우수한 대안을 제공해 줄 것이다. 그러므로 공급사슬관리를 추구하는 기업들은 분 모델을 통해 지속적 협업 통제에 유용한 정보를 얻을 수 있을것이다.

• Composites Research
• /
• 제33권4호
• /
• pp.198-204
• /
• 2020

본 연구에서는 탄소나노튜브 다발을 포함하는 나노복합재료의 열-기계적 특성을 정량적으로 예측하기 위하여 분자동역학 전산모사와 유한요소 기반 균질화 기법을 적용하였다. 응집된 탄소나노튜브의 수가 증가함에 따라 동일한 탄소나노튜브의 체적분율에도 불구하고, 면내 영률 및 면내 전단계수는 감소하였고, 면내 열팽창계수는 증가함을 확인할 수 있었다. 계면의 두께를 조사하기 위하여 밀도의 반경 방향 분포(Radial density distribution)을 조사하였으며, 계면의 두께는 탄소나노튜브의 수와는 거의 무관함을 확인할 수 있었다. 기지와 계면은 등방성 재료로 가정하였으며, 예측한 계면의 열-기계적 특성에 따르면, 응집된 탄소나노튜브의 수가 증가함에 따라 계면의 영률 및 전단계수는 감소하였으며, 열팽창계수는 반대로 증가하였다. 이를 토대로, 탄소나노튜브 다발을 포함하는 PLA 나노복합재료의 열-기계적 특성 예측을 위한 멀티스케일 균질화 모델을 개발하였다.

• 천문학회지
• /
• 제28권2호
• /
• pp.245-253
• /
• 1995

We have analyzed the time series of Ca II H,K and ${\lambda}8498$ line profiles taken for a sunspot (SPO 5007) with the Echelle spectrograph attached to Vacuum Tower Telescope at Sacramento Peak Solar Observatory. Each set of spectra was taken simultaneously for 20 minutes at a time interval of 30 seconds. A total of 40 photographic films for each line was scanned by a PDS at Korea Astronomy Observatory. The central peak intensity of Ca II H ($I_{max}$), the intensity measured at ${\Delta}{\lambda}=-0.1{\AA}$ from the line center of ${\lambda}8498(I_{{\lambda}8489})$, the radial velocity ($V_r$) and the Doppler width (${\Delta}{\lambda}_D$) estimated from Ca II H have been measured to study the dynamical behaviors of the sunspot chromosphere. Fourier analysis has been carried out for these measured quantities. Our main results are as follows: (1) We have confirmed the 3-minute oscillation being dominant throughout the umbra. The period of oscillations jumps from 180 sec in the umbra to 500 to 1000 sec in the penumbra. (2) The nonlinear character of the umbral oscillation is noted from the observed sawtooth shaped radial velocity fluctuations with amplitudes reaching up to $5{\sim}6\;km/sec$. (3) The spatial distribution of the maximum powers shows that the power of oscillations is stronger in the umbra than in the penumbra. (4) The spatial distributions of the time averaged < $I_{max}$ > and < $V_r$ > across the spot are found to be nearly axially symmetric, implying that the physical quantities derived from the line profiles of Ca II H and ${\lambda}8498$ are inherently associated with the geometry of the magnetic field distribution of the spot. (5) The central peaks of the CaII H emission core lead the upward motions of the umbral atmosphere by $90^{\circ}$, while no phase delay is found in intensities between $I_{max}$ and $I_{{\lambda}8498}$, suggesting that the umbral oscillation is of standing waves.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권10호
• /
• pp.693-698
• /
• 1999

Vacuum interrupters have a special asymmetric electrode structure to generate an magnetic field and consequently to increase the interrupting ability. Accordingly 2-dimensional analysis has a large analysis error because radial flux can not be considered. In this paper, in order to analyse the electric field distribution of a vacuum interrupter with arc shield more accurately, 3-dimensional finite element method(FEM) is used. The induced electric potentials of floating shield was increased with the gap distance, which is because the relative position of shield is closer to the fixed contact so that the capacitance distribution inside interrupter is varied. The calculated results also show that the induced potential of shield causes electric field distortion so that the maximum value of electric field in a vacuum interrupter with arc shield is higher than that without one.

• Tribology and Lubricants
• /
• 제28권4호
• /
• pp.153-159
• /
• 2012

Tapered roller bearings are widely used in high axial-load and radial-load applications. In this study, a numerical analysis is performed to study a finite line contacts EHL problem between a tapered roller and raceway in tapered roller bearings. Converged solutions are obtained for moderate load and material parameters using a finite difference method with non-uniform grids and the Newton-Raphson method. The contours and sectional plots of pressure distribution and film shape are compared. The pressure distribution and film shapes near both ends of the roller are very different from those in the central part and are transversely asymmetric. The maximum pressure and absolute minimum film thickness always occur at the small end of the roller.

• Transactions on Electrical and Electronic Materials
• /
• 제18권2호
• /
• pp.111-118
• /
• 2017

The increased diversity of different types of energy sources requires moving towards smart distribution networks. This paper proposes a probabilistic DG (distributed generation) units planning model to determine technology type, capacity and location of DG units while simultaneously allocating ESS (energy storage systems) based on pre-determined capacities. This problem is studied in a wind integrated power system considering loads, prices and wind power generation uncertainties. A suitable method for DG unit planning will reduce costs and improve reliability concerns. Objective function is a cost function that minimizes DG investment and operational cost, purchased energy costs from upstream networks, the defined cost to reliability index, energy losses and the investment and degradation costs of ESS. Electrical load is a time variable and the model simulates a typical radial network successfully. The proposed model was solved using the DICOPT solver under GAMS optimization software.

• 소성∙가공
• /
• 제7권5호
• /
• pp.489-495
• /
• 1998

Spinning is a chipless forming method for producing axially symmetric parts by using axial-radial motions of a spinning roller. This process has still some advantages in such a view point that a variety of complex shapes which can not be formed in a press can be easily spun at a low cost although it is one of the oldest forming methods for spinning mainly cookware parts for a long time. This study is to investigate the optimum roller path in order to obtain the maximum spinnability in producing cylindrical cups of Aluminum(A1050-H16) sheet metal. Working conditions applicable to any size of blank were predetermined through preliminary spinning tests. 9 types of roller path were proposed and experiments were carried out. The modified involute curve was shown to give the maximum drawing ration and more uniform quality of spun cups as compared with other results of this study. in addition thickness distribution and dimensional accuracy of spun cups were examined and discussed.