• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.200-203
• /
• 2006

지역의 공간 분포가 내포된 고해상도의 지상강우량을 추정하기 위해서 강수와 구름 입자(고체와 액체)의 양과 성질을 반영한 기상레이더의 반사도(reflectivity) 자료로부터 지상강우강도로 환산하는 방법이 널리 이용된다. 반사도 (reflectivity) 자료로부터 지상강우강도로 환산하는 핵심은 Z-R 관계식으로, 이 Z-R 관계식의 매개변수 a와 b의 결정이 중요하다. 그러나, 지상우량 관측소에서 측정되는 강우량 자료는 지상에서 관측된 강우자료이나, 레이더에서 추정되는 강우량은 상공 (이 연구에서는1.5km)에서 관측한 반사도로 추정되는 값으로 이에 상응하는 오차를 줄이기 위하여 보정하는 기법이 이용된다. 수계내의 정확한 유출량을 모의계산하기 위하여 수문수치모형이 이용되며, 이의 보다 정확한 수치결과를 모의하기 위해서 레이더 강우추정을 사용하여 정확도를 높이고자 하는 연구가 진행 중이다. 이 연구에서는 기상청에서 운영하는 레이더 반사도 자료를 사용하여 용담/남강유역 내에서 2002-2004년의 집중호우에 대해 Z-R 관계식을 추정하고, 유역 내 평균 강우량과 지상관측 강우량의 비 (G-R비)를 이용한 공간적 특성을 고려한 보정을 함으로써 추정된 평균 강우량의 정확도를 향상시켰다. 이렇게 추정된 레이더 강우는 지상관측지점 강우만으로 보간 된 강우(gauge-only interpolation)와 비교 되어, 레이더강우의 정확성과 적용성이 수문모형에 적합한가를 평가해 보았다. 공간적 분포의 특성을 내포하며 강우예측 (Quantitative Precipitation Forecasting)에 이용될 수 있다는 잇점은 있으나, 레이더 강우 추정은 정확성과 적용성에 많은 의문점을 남긴다.리 전도도 값을 Gardner 식에 적용하여 1, 3, 5, 7kPa에서의 불포화수리 전도도 값을 17개 토양통을 대상으로 하여 구했다. 토양수분 potential이 3kPa에서는 물의 이동이 거의 없는 토양들이 있었는데 반해 남계통을 비롯한 학곡통, 회곡통, 백산통, 상주통, 석천통, 예산통 등 7개의 토양은 3kPa에서도 약간의 물의 이동이 있었다. 이는 모암이 화강 편마암인 관계로 토양 내에 물의 이동에 영향을 미치는 자갈의 함량이 높았기 때문일 것으로 생각되고 추후의 연구에서는 이 부분에 대한 내용도 검토되어야 할 것이다. 또한, 1kPa에서 물의 이동은 삼각통에서 35.21 cm/day로 이동 속도가 가장 컸으며 그 뒤로 예산통, 화봉통, 학곡통, 백산통 등이 토양에서 빠른 속도로 이동하였다. 가천통이나 석천통 및 우곡통은 1kPa에서의 이동 속도가 아주 느린 토양으로 판단되었다. 또한, 포화되지 않은 상태인 1kPa에서 물의 이동 속도를 VGM 모형에 의해 예측된 값과 측정된 값으로 비교하였을 때 불포화 수리 전도도가 예측되지 않은 토양(석천통, 지곡통, 풍천통)이 존재하여 불포화 수리 전도도 특성평가에 대한 VGM 모형의 적용성에 문제를 보였다. 이는 결과적으로 논이라는 영농형태가 존재하는 우리나라에서 토양의 수리적 특성해석을 위한 VGM 모형의 적용성에 한계가 있을 것으로 판단되었다.4일간의 기상변화가 자발성 기흉 발생에 영향을 미친다고 추론할 수 있었다. 향후 본 연구에서 추론된 기상변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기 위한 연구가 필요할 것이다.게 이루어질 수 있을 것으로 기대된다.는 초과수익률이 상승하지만, 이후로는 감소하므로, 반전거래전략을 활용하는

• Journal of the Korean earth science society
• /
• v.35 no.1
• /
• pp.29-40
• /
• 2014

A DC resistivity survey was performed to detect anomalies beneath concrete pavement. A set of high conductive media and planar electrodes were used to lessen the effect's a high contact resistance of concrete. Results of the resistivity survey were analyzed and compared with those of other geophysical surveys such as Ground Penetration Radar (GPR), Impulse Response (IR), and Multi-channel Analysis of Surface Waves (MASW), which were carried out in the same location. The results of resistivity survey showed a high resistive distribution in the section of sink and pavement where a pattern of reinforcement was observed through the GPR survey. Also, a comparison of results between the IR and resistivity surveys indicated that the high resistivity was produced by the high dynamic stiffness in the reinforced section. The co-Kriging of both the results of DC resistivity and MASW surveys at the same location showed that an integrated geostatistical analysis is able to give more accurate description on the anomalous subsurface region than can a separate analysis of each geophysical approach. This study suggests that the integrated geostatistical approaches were used for a decision-making process based on the geophysical surveys.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.684-688
• /
• 2008

레이더 강우와 관련한 대부분의 연구나 실무적용이 제한을 받는 이유는 레이더 반사도 등의 원시자료를 획득하기가 어려울 뿐만 아니라 이를 처리하여 수문해석에 적용하는 과정이 간단하지 않기 때문이다. 이를 해결하기 위하여 다음과 같은 내용을 연구하였다. (1) 레이더 영상자료를 실용적으로 활용하기 위한 '레이더 영상 디지털 변환법(RAIDOM)'을 연구 개발하였다. 또한 오프라인상에서도 기상청 레이더 합성 CAPPI 이미지 자료를 디지털 강우자료로 직접 변환할 수 있는 방법을 제시하였다. 이러한 기술은 앞으로 레이더 강우 연구와 레이더 강우의 활용성을 넓히는데 크게 기여할 것으로 기대된다. (2) RAIDOM 레이더 강우와 연계한 분포형 강우유출모형을 구축하였다. 본 연구에서는 DEM, 토지피복도, 토양도로부터 분포형 강우-유출모형의 매개변수를 산정하는 방법을 상세히 연구하여 제시하였다. 이러한 연구결과는 앞으로 분포형 강우유출모형에 대한 연구와 활용성을 넓히는데 기여할 것으로 기대된다. (3) 주요 관측 레이더 호우사상을 이용하여 RAIDOM 강우와 구축된 분포형 모형의 적용성을 검증하였다. 이를 위하여 먼저 강우유출자료가 체계적으로 관리되고 있는 평창강 국제수문개발계획(IHP) 시범유역의 자료를 이용하여 모형의 매개변수 보정을 수행하였다. 강우 전 하천의 기저유량과 유역의 초기함수조건을 제외한 나머지 매개변수는 유역특성을 나타내는 인자들이므로 모든 강우사상에 대하여 일정한 것으로 가정하여 매개변수 보정을 수행하였다. 6개 주요 호우사상에 대하여 보정한 결과 4개의 호우사상에 대하여 강우-유출과정을 거의 완벽하게 재현하였으며, 2개의 호우사상에 대해서는 수문곡선의 상승과 하강은 비교적 일치하나 첨두부에서 다소차이가 발생하였다. (4) 보정된 분포형 모형을 2006년 7월에 발생한 국지성 집중호우와 한강유역 중상류지역에 걸쳐 큰 홍수량을 발생시킨 2개의 호우사상에 대하여 레이더 강우자료를 적용하여 검토하였다. 검토결과 임진강유역 3개 수위관측소와 우이천수위관측소 및 중랑교수위관측소에서 모의된 홍수수문곡선은 실측치와 잘 일치하는 것으로 나타나 본 연구에서 제시한 RAIDOM과 이를 적용한 분포형 모형이 강우유출 모의를 위하여 활용될 수 있음을 보여주었다. 앞으로 태풍에 수반된 강우와 장마전선 등을 포함한 다양한 유형의 여러 가지 강우에 대한 적용을 통하여 모형의 검증과 보완을 수행하여 RAIDOM 레이더 강우와 분포형 강우유출모형을 연계한 홍수 예보 시스템으로 발전시켜 나갈 예정이다.

• Journal of the Korea Convergence Society
• /
• v.9 no.7
• /
• pp.241-249
• /
• 2018

The military purpose vehicles are developed by using the platform of civil vehicles according to the commercial vehicle expansion plan and military supplied product commercialization policy. But the information related to the military purpose vehicle which adopts the same platform with the civil vehicle is forced to be exposed because its information is revealed by containing into the maintenance manual and electric circuit diagram. Especially, the information disclosure should be blocked by reviewing the application of technology protection because the military vehicle becomes combating purposed mixed equipment when the missile and radar are mounted. The mixed equipment means the one configured with more than 2 types of equipment, and it is categorized into the main and sub equipment. This study was performed to derive the problems in Korean system for vehicle part test evaluation on the mixed equipment and the defense industry technology protection system, and to derive the methods for improving through interviews with the specialists. The conflicts between the civil laws and army regulation were reduced by adding a clause that the engine reflected with the newest emission gas standard should be mounted based on the time of force integration, and the commercialized military supplies were designated as element technology of defense industry technology in consideration of its roles and functions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.2
• /
• pp.185-196
• /
• 1997

By considering the definition and application of resolution as well as the concept and theory of SAR, the essential contents of the SAR design and analysis are described. This paper is to compare and analyze the resolution performance capability of three techniques for achieving azimuth resolution such as the real aperture, the unfocused and the focused techniques, through the simulation. Simulation is performed to make the restricted conditions for the unfocused technique that can be implemented by the less commputing load of signal processingand the lower cost. Through the mission analysis, the use of SAR image can be applied for estimation of whole situation at the regional area in the field of military demands for tactical purpose as well as civilian demands for the damage of disaster. RPV and sall or medium aircraft are selected to carry the SAR for these purposes and the proper resolution turns ou 5~15 m. The trade-off study of variables through the simulations results in the proper conditions such that range is less 3, 000 m, Wavelength is 1~10 m, and the raw signals and results processed by three techniques for two point targets are exhibited undr such conditions. Therefore, at some points, the result of this paper si proposed for useful applications of unforcused technique in the restricted conditions except the identification of the small target at a long range re- quired for high resolution.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.854-864
• /
• 2016

The use of small drone platform has become a popular topic in these days but its application for SAR operation has been little known due to the burden of the payload implementation. Drone platforms are distinguished from the conventional UAV system by the increased vulnerability to the turbulences, control-errors and poor motion stability. Consequently, sophisticated motion compensation may be required to guarantee the successful acquisition of high quality SAR imagery. Extremely limited power and mass budgets may prevent the use of additional hardwares for motion compensation and the difficulty of SAR focusing is further aggravated. In this paper, we have carried out a feasibility study of mico-SAR drone operation. We present the image acquisition results from the preliminary flight tests and a quality assessment is followed on the experimental SAR images. The in-flight motion errors derived from the unique drone movements are investigated and attempts have been made to compensate for the geometrical and phase errors caused by motions against the nominal trajectory. Finally, the successful operation of drone SAR system is validated through the focussed SAR images taken over test sites.

• Journal of Korea Water Resources Association
• /
• v.50 no.10
• /
• pp.681-690
• /
• 2017

This study estimated the daily maximum snow depth using the Artificial Neural Network (ANN) model in Korean Peninsula. First, the optimal ANN model structure was determined through the trial-and-error approach. As a result, daily precipitation, daily mean temperature, and daily minimum temperature were chosen as the input data of the ANN. The number of hidden layer was set to 1 and the number of nodes in the hidden layer was set to 10. In case of using the observed value as the input data of the ANN model, the cross validation correlation coefficient was 0.87, which is higher than that of the case in which the daily maximum snow depth was spatially interpolated using the Ordinary Kriging method (0.40). In order to investigate the performance of the ANN model for estimating the daily maximum snow depth of the ungauged area, the input data of the ANN model was spatially interpolated using Ordinary Kriging. In this case, the correlation coefficient of 0.49 was obtained. The performance of the ANN model in mountainous areas above 200m above sea level was found to be somewhat lower than that in the rest of the study area. This result of this study implies that the ANN model can be used effectively for the accurate and immediate estimation of the maximum snow depth over the whole country.

• Geophysics and Geophysical Exploration
• /
• v.20 no.2
• /
• pp.61-71
• /
• 2017

Recently, ground-penetrating radar (GPR) surveys have been actively carried out for precise subsurface void investigation because of the rapid increase of subsidence in urban areas. However, since the interpretation of GPR data was conducted based on the interpreter's subjective decision after applying only the basic data processing, it can result in reliability problems. In this research, to solve these problems, we analyzed the difference between the events generated from subsurface voids and those of strong diffraction sources such as the buried pipeline by applying the edge detection technique, which is one of image processing technologies. For the analysis, we applied the image processing technology to the GRP field data containing events generated from the cavity or buried pipeline. As a result, the main events by the subsurface void or diffraction source were effectively separated using the edge detection technique. In addition, since subsurface voids associated with the subsidence has a relatively wide scale, it is recorded as a gentle slope event unlike the event caused by the strong diffraction source recorded with a sharp slope. Therefore, the directional analysis of amplitude variation in the image enabled us to effectively separate the events by the subsurface void from those by the diffraction source. Interpretation based on these kinds of objective analysis can improve the reliability. Moreover, if suggested techniques are verified to various GPR field data sets, these approaches can contribute to semiautomatic interpretation of large amount of GPR data.

• Journal of Korea Water Resources Association
• /
• v.48 no.4
• /
• pp.245-255
• /
• 2015

This study used high density network of integrated meteorological sensor, which are operated by SK Planet, with KMA weather stations to estimate the quantitative precipitation field in Seoul area. We introduced SK Planet network and analyzed quality of the observed data for 3 months data from 1 July to 30 September 2013. As the quality analysis result, we checked most SK Planet stations observed similar with previous KMA stations. We developed the real-time quality check and adjustment method to reduce the error effect for hydrological application by missing and outlier value and we confirmed the developed method can be corrected the missing and outlier value. Through this method, we used the 190 stations(KMA 34 stations, SK Planet 156 stations) that missing ratio is less than 20% and the effect of the outlier was the smallest for quantitative precipitation estimation. Moreover, we evaluated reproducibility of rainfall field high density rain gauge network has $3km^2$/gauge. As the result, the spatial relative frequency of rainfall field using SK Planet and KMA stations is similar with radar rainfall field. And, it supplement the blank of KMA observation network. Especially, through this research we will take advantage of the density of the network to estimate rainfall field which can be considered as a very good approximation of the true value.

• Journal of the Korean earth science society
• /
• v.23 no.4
• /
• pp.349-356
• /
• 2002

In an effort to properly assess the validity of spaceborne radar altimeter measurements, we made a direct comparison of two different sea surface heights (SSH) acquired by both Topex/Poseidon (T/P) satellite and in-situ tide-gauges (T/G). This comparative analysis was conducted using the data sets collected from three locations along the eastern coast of Korea which include: Ulleungdo, Pohang, and Sokcho. In the course of the analysis of satellite altimeter, information of SSH was extracted from the T/P MGDR data sets through the application of both atmospheric and geophysical corrections. To compare the T/P data sets in parallel basis, the T/G data sets were averaged using the measured values within the peripheral radius of 55km. When compared among different locations, the compatibility between the two methods was much more significant in an offshore location (Ulleungdo) than the two onshore locations (Pohang, Sokcho). If the low-pass filtered results were compared among the sites, the offshore site exhibited the best correlations between the two methods (correlation coefficient of 0.91) than those of the onshore sites. These large differences in the strength of correlations among different locations are due to the deformation of M2, S2, and K1 tidal components used in the tidal model. In case of the offshore location, the compatibility of the two different methods were improved systematically by the low-pass filtering with an increase of the filtering duration such as up to 200 days.