• Journal of Energy Engineering
• /
• v.25 no.3
• /
• pp.41-50
• /
• 2016

This study examined the combustion characteristics and emissions, fuel economy, acceleration by selecting the two fuel with octane number difference to investigate the effect on the combustion characteristics and performance of the vehicle according to the octane number. First, a single-cylinder engine was used for the combustion characteristic experiment, Of the fuel, which is distributed on the market by the selection of two different octane fuel it is performed experiments. Single cylinder experiment examined the combustion characteristics that appear when you gradually advancing the ignition timing by the ignition timing and air-fuel ratio control for each fuel and through an output, emissions, pressure, hence examined the correlation between by octane number. In addition through the actual vehicle compared the changes in the fuel octane number difference, through acceleration tests examined the impact of the octane number requirements for high-performance segment. As a result, fuel of high octane number in accordance with the ignition timing the advancing showed a slightly stable combustion characteristics, a slight increase occurred in the acceleration test and power. However, both fuel does not significantly differ from the current mode, simulating the urban and highway fuel efficiency. Therefore, the operating conditions of the vehicle currently being sold on the Effects of high-octane fuel. fuel efficiency was found insufficient.

• Journal of the East Asian Society of Dietary Life
• /
• v.21 no.3
• /
• pp.375-384
• /
• 2011

The effects of mixed beans on quality characteristics of traditional soybean paste (Doenjang) were investigated. The proximate composition of the soybean paste (Doenjang) met traditional food standard requirements. The range in salinity was 12.30~13.20%, and the salinity decreased with an increase in the amount of mixed beans. A significant difference in pH values occurred in all samples(p<0.05). The Hunter's 'L ($45.06{\pm}0.41$)' and 'b ($13.89{\pm}0.73$)' values of the TDM2 samples were higher than those of other samples. The highest amounts of malic acid of the organic acids are shown. The order of the amino acid content was aspartic acid > leucine > lysine, and that of free amino acid contents were proline > glutamic acid > arginine. The order of mineral content in the soybean pastes was Na > K > Ca > Mg, but levels of Co, Cu, and Zn were not detected. The traditional soybean paste (Doenjang) had an effective DPPH radical scavenging activity and higher phenolic content compared to those of the control sample. Overall acceptability score of the TDM2 (soybean 1 : mixed beans 1) was higher than that of the others. More research is needed to enhance the quality and functionality of traditional soybean paste.

• Food Science and Preservation
• /
• v.15 no.1
• /
• pp.21-29
• /
• 2008

This study investigated the fermentation and quality characteristics of a fermented beverage, prepared by semi-anaerobic culture, using sea tangle extract. A central composit design using alcohol(0, 0.5, 1.0, 1.5, 2.0% [all v/v] ), sugar(0, 5, 10, 15, 20% [all w/v] ) and $65^{\circ}Brix$ citrus juice(0, 1.0, 2.0, 3.0, 4.0 % [all v/v] ) was used to find the optimal mix for fermentation. Sensory characteristics, such as color, flavor, taste, sweetness, saltiness, sourness and overall quality, were measured using a response surface methodology computer program. The optimal conditions that produced the highest acidity of 0.94 were 2.0 % ethanol, 10.17 % sucrose and 1.99 % citrus juice. The optimal conditions that produced gel 20.13 nun in thickness were 1.98% alcohol, 10.94% sucrose and 1.62% citrus juice. The overall optimal conditions that satisfied all the sensory requirements for a sea tangle beverage were 1.0% alcohol, 10.0% sucrose and 4.05% citrus juice.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.7
• /
• pp.1770-1780
• /
• 1997

Our problem is improvement of image quality because it is inevitable cell loss of image data when traffic congestion occurs. If cells are discarded indiscriminately in transmission of MPEG video data, it occurs severe degradation in quality of service(QOS). In this paper, to solve this problem, we propose two method. The first, we analyze the traffic characteristics of an MPEG encoder and generate high priority and low priority data stream. During network congestion, only the least low priority cells are dropped, and this ensures that the high priority cells are successfully transmitted, which, in turn, guarantees satisfactory QoS. In this case, the prioritization scheme for the encoder assigns components of the data stream to each priority level based on the value of a parameter ${\beta}$. The second, Number of high priority cells are increased when value of ${\beta}$ is large. It occurs the loss of high priority cell in the congestion. To prevent it, this paper is regulated to data stream rate as buffer occupancy with UPC controller. Therefore, encoder's bandwidth can be calculated renegotiation of the encoder and networks. In this paper, the encoder's bandwidth requirements are characterized by a usage parameter control (UPC) set consisting of peak rate, burstness, and sustained rate. An adaptive encoder rate control algorithm at the Networks Interface Card(NIC) computes the necessary UPC parameter to maintain the user specified quality of service. Simulation results are given for a rate-controlled VBR video encoder operating through an ATM network interface which supports dynamic UPC. These results show that dynamic bandwidth renegotiation of prioritized data stream could provided bandwidth saving and significant quality gains which guarantee high priority data stream.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.4
• /
• pp.115-123
• /
• 2021

In recent years, the automobile industry has been facing a major change with the introduction of new technologies represented by autonomous driving, electrification, and digitalization. Major domestic and overseas automakers are trying to use a systematic approach to customer satisfaction through user interfaces to provide customers with a special experience and value beyond just making products with high performance. This study proposes the Kano model as a systematic and qualitative research method for satisfaction. As a case study, 17 functions of a product were sorted (3 operation functions, 7 safety functions, and 7 convenience functions). This was done by analyzing the use case and the customers' requirements for a smart trunk system. 18 new functions were derived via creative ideation codes. In addition, a scientific analysis method is proposed for product quality attributes and the strength of customer satisfaction. Using the Kano methodology, 25 functions were classified into quality attributes: 18 attractive qualities, 3 one-dimensional qualities, and 4 complex qualities, which are combinations of one-dimension qualities and must-have qualities. The functions that have one-dimensional quality and complex qualities were found to have higher customer ratings than the functions that have attractive qualities. Based on this, enterprises could effectively reduce customer complaints and enhance customer satisfaction.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.65-83
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well. 2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air. 3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying. 4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis. 5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time. 6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture. 7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation. 8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise. 11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss. 12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method. 13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated. Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year. 14. Required fan horsepower and energy for the intermittent fan operation were 3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation. 15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use. 16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.64-64
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well.2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air.3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying.4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis.5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time.6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture.7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation.8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise.11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss.12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method.13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated.Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year.14. Required fan horsepower and energy for the intermittent fan operation were3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation.15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use.16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• Management & Information Systems Review
• /
• v.37 no.4
• /
• pp.1-20
• /
• 2018

This study aimed to examine earnings quality of firms selected as Global Champs project which has been promoted by the government since 2013 to support small and medium sized enterprises, for the screening year(t-1) and selected year(t). Earing quality is measured as the value of discretionary accruals estimated by Dechow et al.(1995) adjusted Jones model and Kothari et al.(2005) model, respectively. I analyze the differences of earning quality between the Global Champ firms and the paired firms selected through criteria of the similar total assets and the same industry in the screening year and the selected year. This study is motivated by the needs of measurement of the performance of the Project from the accounting transparent point of view. As the results of this study, major findings are summarized as follows. Firstly the earnings quality of the selected firms was lower than that of the paired firms. This can be explained as a result of motivation of earnings management by companies eager to meet the requirements to be selected for the Project. Secondly, in the selected year, the earnings quality was proved to improve, comparing to the screening year. This can be explained by the efforts of companies to reinforce management innovation and transparent management, which in turn led to positive effects on the earnings quality. These findings were found to be consistent in the additional analyses, where the earning quality of the reconstructed sample with only selected companies was compared for the screening year and the selected year, based on the year before the screening year(t-2).

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.47
• /
• pp.63-94
• /
• 2002

On the purpose to suggest an advanced scheme in assessing the domestic wheat quality, this paper reviewed the inspection systems of wheat in major wheat producing countries as well as the quality criteria which are being used in wheat grading and classification. Most wheat producing countries are adopting both classifications of class and grade to provide an objective evaluation and an official certification to their wheat. There are two main purposes in the wheat classification. The first objectives of classification is to match the wheat with market requirements to maximize market opportunities and returns to growers. The second is to ensure that payments to glowers aye made on the basis of the quality and condition of the grain delivered. Wheat classes has been assigned based on the combination of cultivation area, seed-coat color, kernel and varietal characteristics that are distinctive. Most reputable wheat marketers also employ a similar approach, whereby varieties of a particular type are grouped together, designed by seed coat colour, grain hardness, physical dough properties, and sometimes more precise specification such as starch quality, all of which are genetically inherited characteristics. This classification in simplistic terms is the categorization of a wheat variety into a commercial type or style of wheat that is recognizable for its end use capabilities. All varieties registered in a class are required to have a similar end-use performance that the shipment be consistent in processing quality, cargo to cargo and year to year, Grain inspectors have historically determined wheat classes according to visual kernel characteristics associated with traditional wheat varieties. As well, any new wheat variety must not conflict with the visual distinguishability rule that is used to separate wheats of different classes. Some varieties may possess characteristics of two or more classes. Therefore, knowledge of distinct varietal characteristics is necessary in making class determinations. The grading system sets maximum tolerance levels for a range of characteristics that ensure functionality and freedom from deleterious factors. Tests for the grading of wheat include such factors as plumpness, soundness, cleanliness, purity of type and general condition. Plumpness is measured by test weight. Soundness is indicated by the absence or presence of musty, sour or commercially objectionable foreign odors and by the percentage of damaged kernels that ave present in the wheat. Cleanliness is measured by determining the presence of foreign material after dockage has been removed. Purity of class is measured by classification of wheats in the test sample and by limitation for admixtures of different classes of wheat. Moisture does not influence the numerical grade. However, it is determined on all shipments and reported on the official certificate. U.S. wheat is divided into eight classes based on color, kernel Hardness and varietal characteristics. The classes are Durum, Hard Red Spring, Hard Red Winter, Soft Red Winter, Hard White, soft White, Unclassed and Mixed. Among them, Hard Red Spring wheat, Durum wheat, and Soft White wheat are further divided into three subclasses, respectively. Each class or subclass is divided into five U.S. numerical grades and U.S. Sample grade. Special grades are provided to emphasize special qualities or conditions affecting the value of wheat and are added to and made a part of the grade designation. Canadian wheat is also divided into fourteen classes based on cultivation area, color, kernel hardness and varietal characteristics. The classes have 2-5 numerical grades, a feed grade and sample grades depending on class and grading tolerance. The Canadian grading system is based mainly on visual evaluation, and it works based on the kernel visual distinguishability concept. The Australian wheat is classified based on geographical and quality differentiation. The wheat grown in Australia is predominantly white grained. There are commonly up to 20 different segregations of wheat in a given season. Each variety grown is assigned a category and a growing areas. The state governments in Australia, in cooperation with the Australian Wheat Board(AWB), issue receival standards and dockage schedules annually that list grade specifications and tolerances for Australian wheat. AWB is managing "Golden Rewards" which is designed to provide pricing accuracy and market signals for Australia's grain growers. Continuous payment scales for protein content from 6 to 16% and screenings levels from 0 to 10% based on varietal classification are presented by the Golden Rewards, and the active payment scales and prices can change with market movements.movements.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.5
• /
• pp.720-732
• /
• 2001

Skeletal muscle is of major economic importance since it is finally converted to meat for consumers. The increase in meat production with low costs of production may be achieved by optimizing muscle growth, whereas a high meat quality requires, among other factors, the optimization of intramuscular glycogen and fat stores. Thus, research in energy metabolism aims at controling muscle metabolism, but also liver and adipose tissue metabolism in order to optimize energy partitioning in favour of muscles. Liver is characterized by high anabolic and catabolic rates. Metabolic enzymes are regulated by nutrients through short-term regulation of their activities and long-term regulation of expression of their genes. Consequences of liver metabolic regulation on energy supply to muscles may affect protein deposition (and hence growth) as well as intramuscular energy stores. Adipose tissues are important body reserves of triglycerides, which result from the balance between lipogenesis and lipolysis. Both processes depend on the feeding level and on the nature of nutrients, which indirectly affect energy delivery to muscles. In muscles, the regulation of rate-limiting nutrient transporters, of metabolic enzyme activities and of ATP production, as well as the interactions between nutrients affect free energy availability for muscle growth and modify muscle metabolic characteristics which determine meat quality. The growth of tissues and organs, the number and the characteristics of muscle fibers depend, for a great part, on early events during the fetal life. They include variations in quantitative and qualitative nutrient supply to the fetus, and hence in maternal nutrition. During the postnatal life, muscle growth and characteristics are affected by the age and the genetic type of the animals, the feeding level and the diet composition. The latter determines the nature of available nutrients and the rate of nutrient delivery to tissues, thereby regulating metabolism. Physical activity at pasture also favours the orientation of muscle metabolism, towards the oxidative type. Consequently, breeding systems may be of a great importance during the postnatal life. Research is now directed towards the determination of individual tissue and organ energy requirements, a better knowledge of nutrient partitioning between and within organs and tissues. The discovery of new molecules (e. g. leptin), of new molecular mechanisms and of more powerful techniques (DNA chips) will help to achieve these objectives. The integration of the different levels of knowledge will finally allow scientists to formulate new types of diets adapted to sustain a production of high quality meat with lower costs of production.