• Korean Journal of Optics and Photonics
• /
• v.8 no.2
• /
• pp.111-115
• /
• 1997

Vertical-cavity surface-emitting laser(VCSEL)s operating at 1.3-micron wavelength for optical communication are fabricated by using Si/SiO$_2$dielectric quater-wave pairs on both sides of the InGaAsP(${\lambda}_g$=1.3 ${\mu}{\textrm}{m}$) gain material. VCSELs are optically pumped with a Nd-YAG laser in a pulsed mode and lasing around 1.3 microns is observed. Lasing characteristics such as threshold pump intensity as a function of mirror-reflectivity, polarization, and threshold pump density with pump spot size are investigated.

• Steel and Composite Structures
• /
• v.36 no.3
• /
• pp.249-259
• /
• 2020

In this work, a novel three-dimensional model in the generalized thermoelasticity for a homogeneous an isotropic medium was investigated with diffusion, under the effect of thermal loading due to laser pulse in the context of Green-Lindsay theory was investigated. The normal mode analysis technique is used to solve the resulting non-dimensional equations of the problem. Numerical results for the displacement, the thermal stress, the strain, the temperature, the mass concentration, and the chemical potential distributions are represented graphically to display the effect of the thermal loading due to laser pulse and the relaxation time on the resulting quantities. Comparisons are made within the theory in the presence and absence of laser pulse.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.378-381
• /
• 2002

This paper describes a novel multilevel ad/dc power converter suitable for the protection of frequent output short-circuit. The output dc power of the proposed converter can be disconnected from the load within several hundred microseconds at the instant of short-circuit fault. The rising time of the dc load voltage is as small as several hundred microseconds, and there is no overshoot of the do voltage because the dc output capacitors keep undischarged state. Analysis and simulations are carried out to investigate the operation and usefulness of the proposed scheme.

• Journal of Welding and Joining
• /
• v.16 no.4
• /
• pp.63-72
• /
• 1998

In this study, the effects of the current pulsing conditions, on the spatter generation rate during the $CO_2$ gas metal arc welding (GMAW) were investigated. Normally using the inverter type power supply, of which the welding current waveform was regulated to reduce the spatter generation rate, but in this study pulsing was imposed on the welding current. Observation of the metal transfer phenomena during the pulsed current GMAS indicated that the droplet transfer from the electrode via the short circuit transfer and the repelling transfer mode could be minimized by selecting optimum combinations of pulsing parameters, which include base and peak current, base and pak duration. It was also demonstrated in this study that proper combinations of the pulsing parameters led to reduce generation of spatters during GMAW shielded by $CO_2$ gas.

• Journal of the Korean Society of Visualization
• /
• v.16 no.1
• /
• pp.48-53
• /
• 2018

In this study, the effect of injection pressure on the column diameter and droplet velocity of liquid jet with the weakly turbulent Rayleigh-like breakup mode is experimentally studied using digital microscopic holography (DMH). The injection nozzle has the diameter of $50{\mu}m$ and injection pressure is varied from 0.1 to 0.4 MPa. When the micro liquid jet is injected into still air, the double-pulsed holograms was recorded on a CCD sensor and numerically reconstructed in order to obtain well focused images. In this study, the liquid column diameter from $50{\mu}m$ orifice nozzle is shown to be changed slightly but the droplet velocity is increased proportionally as the injection pressure is increased.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1905-1907
• /
• 1997

The experiments of laser-guided de discharge were carried out by using pulsed Nd:YAG laser radiation at low air pressure ranging from 0.3 to 20 torr. The minimum laser-guided de discharge voltages($V_{MD}$) at given pressure and distances between anode and cathode electrode were obtained. In order to generate TEM(transverse electromagnetic waves) modes, a pinhole was installed between a rod and a half mirror, and its diameter was adjusted from 6mm to 1.7mm. And then, we investigated the characteristics of laser-guided de discharge corresponding to different TEM modes. As a result, it was found that $V_{MD}$ at $TEM_{00}$ mode was lower than $V_{MD}$ at multimodes.

• The Journal of the Acoustical Society of Korea
• /
• v.17 no.4
• /
• pp.67-71
• /
• 1998

초음파 선형트랜스듀서에서 제한회절음장은 영상깊이에서 다른 방향으로 진행하는 평면파들의 선형적인 중첩으로부터 구한다. 제한회절음장을 구현하기 위한 송신음장은 영상 깊이를 지나가는 평면파들의 공간적인 확장으로부터 구해지는데 실제의 하드웨어로 구현하 기 어렵다. 본 논문은 진행방향이 다른 pulsed mode 평면파를 각각 송신한 후, 얻어진 데이 터로부터 합성집속 방법에 의하여 제한회절빔을 구현하였다. 제안한 방법은 모든 송신소자 에서 발사되는 음장의 크기가 동일하므로 송신전력이 증가하여 신호대잡음비와 명암비를 증 가시키며 간단한 하드웨어로 구현이 가능하다. 시뮬레이션 결과는 송신은 한점집속, 수신은 동적집속을 사용하는 기존의 방법과 비교하여 주엽(mainlobe)의 폭과 부엽(sidelobe)의 크기 관점에서 우수함을 증명하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.71-72
• /
• 2008

In this paper, the effect of thermal annealing on surface acoustic wave (SAW) properties of aluminum nitride (AlN) films were described. The films were fabricated on Si substrates by using Pulsed Reactive Magnetron Sputtering System. The SAW properties of $600^{\circ}C$-annealed AlN films were better than those of both $900^{\circ}C$-annealed AlN films and as-deposited ones. Their SAW velocities (Raleigh mode) and insertion losses were about 5212 m/s and 16.19 dB at $600^{\circ}C$ with the wavelength of $40{\mu}m$. The dependence of characteristics of AlN films on annealing conditions were also evaluated by using Fourier Transform-Infrared Spectroscopy (FT-IR) Spectrums and Atomic Force Microscopy (AFM).

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.3 no.2
• /
• pp.13-21
• /
• 1997

This paper describes the effectiveness of laser pulse shaping in eliminating weld defects such as porosity, cracks and undercuts in pulsed Nd:YAG Laser welding. A large porosity was formed in a keyhole mode of deep penetration weld metal of any stainless steel. Solidification cracks were present in Type 303 with about 0.3%s. The conditions for the formation of porosity were determined in further detail in Type 316. With the objectives of obtaining a fundamental knowledge of formation and prevention of weld defects, the fusion and solidification behavior of a molten puddle was observed during laser spot welding of Type 310S. through high speed video photographing technique. It was deduced that cellular dendrite tips grew rapidly from the bottom to the surface, and consequently residual liquid remained at the grain boundaries in wide regions and enhanced the solidification cracking susceptibility. Several laser pulse shapes were investigated and optimum pulse shapes were proposed for the reduction and prevention of porosity and solidification cracking.

• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1680-1690
• /
• 2006

As a promising and novel manufacturing technology, laser aided direct metal deposition (DMD) process produces near-net-shape functional metal parts directly from 3-D CAD models by repeating laser cladding layer by layer. The key of the build-up mechanism is the effective control of powder delivery and laser power to be irradiated into the melt-pool. A feedback control system using two sets of optical height sensors is designed for monitoring the melt-pool and real-time control of deposition dimension. With the feedback height control system, the dimensions of part can be controlled within designed tolerance maintaining real time control of each layer thickness. Clad nugget shapes reveal that the feedback control can affect the nugget size and morphology of microstructure. The pore/void level can be controlled by utilizing pulsed-mode laser and proper design of deposition tool-path. With the present configuration of the control system, it is believed that more innovation of the DMD process is possible to the deposition of layers in 3-D slice.