• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.3
• /
• pp.255-261
• /
• 2007

By using numerical analysis methods, through transmission type pulsed eddy current (PEC) testing is modeled and PEC signal responses due to varying material conductivity, permeability, thickness, lift-off and pulse width are investigated. Results show that the peak amplitude of PEC signal gets reduced and the time to reach the peak amplitude is increased as the material conductivity, permeability, and specimen thickness increase. Also, they indicate that the pulse width needs to be shorter when evaluating the material conductivity and the plate thickness using the peak amplitude, and when the pulse width is long, the peak time is found to be more useful. Other results related to lift-off variation are reported as well.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.3
• /
• pp.280-289
• /
• 2015

A high-efficiency full-bridge DC-DC converter with a current-doubler rectifier and an asymmetric pulse-width modulation is proposed. Through the asymmetric pulse-width modulation, the proposed converter achieves zero-voltage switching of power switches without the circulating currents. The proposed converter reduces the output current ripple through the current-doubler rectifier. A control strategy is suggested for the proposed converter to charge battery banks. A constant current and constant voltage charging is performed. The proposed converter achieved a higher efficiency compared with the conventional full-bridge DC-DC converter with a phase-shift modulation. The performance of the proposed converter is evaluated by the experimental results for a 1.0 kW prototype circuit.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.85-95
• /
• 1997

This study is to investigate the optimum conditions of Nd:YAG laser beam welding for Zircaloy-4 end cap closure by optical fiber transmission. Laser welding parameters which affect the penetration depth and bead width were experimentally examined using the various beam radius by the beam quality analyzer, joint geometries of end cap and the laser parameters which mean pulse width, repetition rate and pulse energy. Also, an optimum welding speed and the effect of assistant gas with varying the flow rate of He were investigated. We found that the laser average power for the end cap welding will be 230W and rotation speed must not exceed 8 RPM, the best position of focus using optical fiber with 600.mu.m will be 2 to 3mm below the surface of the material.

• Journal of Power Electronics
• /
• v.14 no.5
• /
• pp.937-945
• /
• 2014

This paper presents an optimized space vector pulse-width modulation (OSVPWM) technique for a five-level cascaded H-bridge (CHB) inverter. The space vector diagram of the five-level CHB inverter is optimized by resolving it into inner and outer two-level space vector hexagons. Unlike conventional space vector topology, the proposed technique significantly reduces the involved computational time and efforts without compromising the performance of the five-level CHB inverter. A further optimized (FOSVPWM) technique is also presented in this paper, which significantly reduces the complexity and computational efforts. The developed techniques are verified through MATLAB/SIMULINK. Results are compared with sinusoidal pulse-width modulation (SPWM) to prove the validity of the proposed technique. The proposed simulation system is realized by using an XC3S400 field-programmable gate array from Xilinx, Inc. The experiment results are then presented for verification.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.388-397
• /
• 2016

An error-compensated pulse width modulator (ECPWM) is proposed to improve the baseband harmonic performance and the switching loss of voltage source inverters (VSIs). Selecting between harmonic distortion and switching loss is a design tradeoff in the conventional space vector pulse width modulation. In this work, an accumulated difference in produced and desired phase voltages is considered to adjust the reference signal. This mechanism can compensate for the voltage error in the previous carrier period. With error compensation every half-carrier period, the proposed ECPWM allows one-half reduction in carrier frequency without scarifying baseband harmonic distortion. The proposed modulator is applied to a three-phase VSI with R-L load and a motor-speed-control system for experiments. The measured efficiency and operating temperature of switches confirm the effectiveness of the proposed scheme.

• Journal of Power Electronics
• /
• v.18 no.1
• /
• pp.137-146
• /
• 2018

This paper describes a single pulse-width modulation control strategy using the Single Pulse-Width Modulation (SPWM) method with a soft-switching technique for a wide range of output voltages from a bidirectional Dual-Active Bridge (DAB) converter. This method selects two typical inductor current waveforms for soft-switching, and proposes a rule that makes it possible to achieve soft-switching without any compensation algorithm from the waveforms. In addition, both the step-up and step-down conditions are analyzed. This paper verifies that the leakage inductance is independent from the rule, which makes it easier to apply in DAB converters. An integrated algorithm, which includes step-up and step-down techniques, is proposed. The results of experiments conducted on a 50-kW prototype are presented. The system efficiency is experimentally verified to be from 85.6% to 97.5% over the entire range.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.8
• /
• pp.1552-1557
• /
• 2007

In this work, temperature stable pulse width modulation controller using bandgap reference voltage is proposed. Two bandgap reference voltages are designed by using BiCMOS technology which are temperature dependent and independent voltage references. PWM controller is designed by using 3.3 volt supply voltage and the output frequency is 1MHz. From simulation results, the variation of output pulse width is less than form +0.86% to -0.38% in the temperature range $0^{\circ}C\;to\;70^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04a
• /
• pp.152-154
• /
• 2000

Electro_optical characteristics in AC-PDP are confined by a lots of parameters. especially driving pulse shape is very important to improve AC-PDP's luminosity and efficiency. In that experiment measure the luminosity, IR(Infra Red) peak value and response time as the increase of 1st, 2rd sustain pulse width. The VDS(Versatile Driving Simulator -developed by kwangwoon university-) was used to make driving pulse shape. It is found that IR response time after displacement current, Luminosity and IR peak value are changed on account of 1st,2rd sustain pulse width.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.942-948
• /
• 2011

Solid propulsion systems have simple structures compared to other propulsion systems and are suitable for long-term storage. However the systems generally have limits on control of thrust levels. In this paper we introduce controllers for combustion chamber pressure using on-off control techniques which have been known for relatively easy implementation and energy efficiency. For this, we use a simple pressure change model by considering only mass conservation within the combustion chamber and we design a classical controllers and on-off controllers with are Pulse Width Modulation(PWM) and Pulse Width Pulse Frequency Modulation (PWPFM). Then we compare the performance results of the controllers through numerical simulations.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.7
• /
• pp.17-22
• /
• 2008

This paper presents a low-power and small-area pulse width modulator by light intensity for photoflash. Light intensity controller is achieved by using capacitor, photodiode, and comparator. The proposed circuit designs digital circuit to reduce static power consumption except comparator. And IGBT driver has short circuit protection using delay cell. The pulse width modulator has the operating range of $V_{MS}$ from 0.5V to 2.5V and pulse width of output from 0.14ms to 1.65ms at 300Hz. The pulse width modulator fabricated in $0.35-{\mu}m$ CMOS technology occupies $0.85mm{\times}0.56mm$. This circuit consumes 3.0mW at 300Hz and 3.0V.