• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2006.11a
• /
• pp.128-132
• /
• 2006

Low-k wafer engraving process has been investigated by using UV pico-second laser with high repetition rate. Wavelength and repetition rate of laser used in this study are 355nm and 80MHz, respectively. Main parameters of low-k wafer engraving processes are laser power, work speed, assist gas flow rate, and protective coating to eliminate debris. Results show that engraving qualities of low-k layer by using UV pico-second pulse width and high repetition rate had better kerf edge and higher work speed, compared to one by conventional laser with nano-second pulse width and low repetition rate in the range of kHz. Assist gas and protective coating to eliminate debris gave effects on the quality of engraving edge. Total engraving width and depth are obtained less than $20{\mu}m$ and $10{\mu}m$ at more than 500mm/sec work speed, respectively. We believe that engraving method by using UV pico-second laser with high repetition rate is useful one to give high work speed of laser material process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.185-186
• /
• 2009

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.1
• /
• pp.32-44
• /
• 2001

The purpose of this study was to investigate the effects of Er : YAG laser on cutting efficacy and temperature changes of dentin. We used the dentin specimens of human premolars and molars which contain the physiologic saline and maintain the pulpal pressure in dentinal tubules. Each specimen was exposed to Er : YAG laser with non-contact handpiece type delivery system under different treatment condition of irradiation energy, pulse repetition rate, and exposure time. Two procedures were conducted by the presence of water flow during lasing. The specimens were grouped by thickness of dentin. We investigated the cavity pattern, volume, and temperature change of dentin specimen to determine the cutting efficacy and temperature rise of Er : YAG laser, and obtained following results. 1. Cutting volume of dentin was increased by increasing the irradiation energy, pulse repetition rate, and exposure time(P<0.05). 2. Margins of abulated cavities were sharp and clean and floors of cavities were conical in shape and showing smooth surfaces. Upper diameter of abulated cavities were increasing as laser parameter of irradiation energy, pulse repetition rate, and exposure time were increased. A few cracks were observed on abulated surfaces under treatment condition of laser parameter with 150mJ, 5Hz, and 5sec. 3. Temperature was increased as laser parameter of irradiation energy, pulse repetition rate, and exposure time were increased, and temperature rise was decreased as dentin thickness was increased(P<0.05). 4. Temperature rise was decreased under water flow compared with no water flow during laser exposure(P<0.05). From these results, we think that the method of using a Er:YAG laser would be effective and safe in cutting dentin for clinical application.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1729-1731
• /
• 2003

Recently many solid-state laser systems were widely used in the medical applications. So it is necessary to study various optimal laser parameters for adopting new medical treatments. Alexandrite laser using switching mode power supply has designed and experimented to adjust a pulse repetition rate by PIC one-chip microprocessor. The fundamental results have been obtained during the first financial year in 2002. We will be able to find out the optimal hair removal characteristics by the repetitive experiments of Alexandrite laser as the parameters such as pulse repetition rate, pulse width, and pulse energy etc.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.74-77
• /
• 2000

A pulsed Nd:YAG laser has been used in a wide variety of fields : measuring, material processing and so on. In a material processing, it is very important to control the laser energy density. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this study, pulsed Nd:YAG laser system was designed and manufactured to control the laser output usefully and easily. This system adopted the sequential charge and discharge circuit is controlled by 80196 micro- processor. As a result, it is found that laser output is controlled minutely by changing laser input and pulse repetition rate, and usefully by using 80196 microprocessor.

• Laser Solutions
• /
• v.16 no.2
• /
• pp.1-6
• /
• 2013

Picosecond lasers are a very effective tool for micromachining metals, especially when high accuracy, high surface roughness and no heat affected zone are required. However, low productivity has been a limit to broadening the spectrum of their industrial applications. Recently it was reported that in the micromachining of copper with a 1064nm picosecond laser, there exist the optimal pulse energy and repetition rate to achieve the maximum volume ablation rate. In this paper, we used a 515nm picosecond laser, which is more efficient for micromachining copper in terms of laser energy absorption, to obtain its optimal pulse energy and repetition rate. Theoretical analysis based on the experimental data on copper ablation showed that using a 515nm picosecond laser instead of a 1064nm picosecond laser is more favorable in that the calculated threshold fluence is 75% lower and optical penetration depth is 50% deeper.

• Journal of the Optical Society of Korea
• /
• v.8 no.1
• /
• pp.29-33
• /
• 2004

We propose and demonstrate a novel optical pulse multiplier applicable to OTDM (Optical Time Division Multiplexing) systems using cascaded long-period fiber gratings. We have exploited the fact that each mode in a fiber has a different propagation constant to obtain time delays among optical pulses. The proposed scheme could realize high-frequency optical pulse multiplication for optical short pulse trains. We have successfully implemented two, four, and eight times multiplications with the maximum repetition rate of 416.7 ㎓. The obtained pulse delays are well matched with the simulated ones.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1060-1062
• /
• 1999

Pulsed Nd:YAG laser is used widely for materials processing and instrumentation. It is very important to control the laser energy density in materials processing by a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this study, the alternating charge-discharge system was designed to adjust a pulse repetition rate. And the parallel mesh is added to increase laser output power. This system is controlled by one chip microprocessor and allows to replace an expensive condenser for high frequency to a cheap condenser for low frequency. In addition, we have investigated the current pulse shape of flashlamp and the operating characteristics of a pulsed Nd:YAG laser. As a result, it is found that the laser output of the power supply using the parallel mesh and the alternating charge-discharge system is not less than that of typical power supply. As the pulse repetition rate rises from 10pps to 110pps by the step of 20pps at 1000V and 1200V, it is found that the laser efficiency decreases but the laser output power increases about 5W at each step.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2204-2206
• /
• 1999

Pulsed Nd:YAC laser is used widely for materials processing and instrumentation. It is very important to control the laser energy density in materials processing by a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this study, the alternating charge-discharge system was designed to adjust a pulse repetition rate. This system is controlled by one chip microprocessor and allows to replace an expensive condenser for high frequency to a cheap condenser for low frequency. In addition. we have investigated the current pulse shape of flashlamp and the operating characteristics of a pulsed Nd:YAG laser. As a result, it is found that the laser output of the power supply using the alternating charge-discharge system is not less than that of typical power supply. As the pulse repetition rate rises from 30pps to 120pps by the step of 30pps at 1200V, it is found that the laser efficiency decreases but the laser output power increases about 6W at each step.

• Journal of the Optical Society of Korea
• /
• v.18 no.5
• /
• pp.611-615
• /
• 2014

We report high-speed pulse train generation from a relatively low-speed 10-GHz mode-locked laser by means of line-by-line spectral coding. To increase the pulse repetition rate multiplication (RRM) factor, we combine coding schemes for both spectral intensity and phase by placing a simple mask at the coder focal plane. The resulting RRM factor, determined by multiplying the RRM factors of the individual coding schemes, rises as high as 16. To verify the generated pulses, the optical spectra and autocorrelation traces are examined.