• 소음진동
• /
• 제6권3호
• /
• pp.357-362
• /
• 1996

The magnetic levitation system has great advantages, such as little friction, no lubrication, no noise and so on. But the magnetic levitation system need a stabilizing controller because it is a unstable, system in natural and it need a sensor for displacement measurement to control the system. In this paper, we proposed a sensorless method to measure the gap between the magnetic pole and the levitated object with application the inductance characteristic which vary according to gap. We made a driving circuit which supply simultaneously the control input PWM(Pulse Width Modulation) signal and the carrier PWM signal to estimate the gap. Because the inductance is a function of gap, and the current of the carrier signal is a function of the inductance, we could estimate the gap from the measurement of the current of the carrier signal. Finally, we investigated the validity of the proposed method through the experimental results.

• 조명전기설비학회논문지
• /
• 제19권4호
• /
• pp.98-107
• /
• 2005

브러시리스 DC 전동기(BLDCM)는 일반적으로 $120[^{\circ}]$ 구형파 전압을 인가하여 구동하며 속도 제어를 위하여 2상 PWM 형태의 펄스로 이를 인가한다. 본 논문은 네 가지 PWM 방법을 이용한 BLDCM 제어 시스템을 소개하고, 2차원 시간차분 유한요소법을 이용하여 각 PWM 방식에 따른 전동기 성능 특성을 해석하고 비교한다. 또한 제안한 해석 기법의 타당성을 입증하기 위하여 BLDCM 시작기를 제작, 실험을 통하여 해석치와 실험치를 비교한다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1406-1409
• /
• 2004

The Resolver usually used in industry is the absolute angle analog sensor that must be in order to driving BLDC (brushless DC) motor, and it needs RDC(Resolver-to-Digital converter) for changing the output signal to digital to be applied to the SVPWM(Space Vector Pulse Width Modulation) algorithm. Commonly used S/W RDC needs trigonometric function. What it takes a lot of calculation time of processor is gotten at weak point. In this paper, S/W RDC is realized except trigonometric functions as a result of feedback resolver outputs after filtering using FIR filter. thus, processing time is reduced. So, One-chip DSP Controller operating the Vector Control, RDC, and SVPWM can be designed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.582-584
• /
• 1994

A sinusoidal rotatory chair system using a self-tuning and following control by a fuzzy was designed to evaluate the vestibular function and to apply to a robot driving power system. The experimental results by the sinusoidal rotatory chair system were pretty good and whitch had smaller then ${\pm}210$ pulse error on the ${\pm}810^{\circ}$ sinusoidal rotation at 0.12 Hz by using a 850W DC servo motor. As a results, the sinusoidal rotatory chair system may be useful to evaluate the vestibular function in the field of medicine, and it can be used to robotics or a numerical control system (NC) on the industry if the the obtained control method and the system are adapted for a channel.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 학술대회 논문집
• /
• pp.57-62
• /
• 2004

본 연구에서는 3전극 면방전 AC PDP의 ADS 구동방식에서 구동펄스 인가조건에 따른 어드레스 방전과 표시 방전간의 영향을 실험적으로 해석하고 휘도특성에 대해 알아보았다. 어드레스 방전을 위한 최소의 어드레스 펄스폭은 $1.5{\mu}s$이며 전압마진은 35V이다. 표시방전을 위한 최소 표시방전유지 펄스폭은 $2{\mu}s$이며 전압마진은 25V이다. 이때 최대 휘도를 위한 표시방전 전압은 190V이며 표시방전 펄스의 개수가 1024개일 때 얻어진 평균휘도는 $310[cd/m^2]$이다.

• 전기학회논문지
• /
• 제59권9호
• /
• pp.1615-1620
• /
• 2010

A thin film thermoelectric cooler for COB direct assembly was proposed and the COB cooler structure was modeled by electrical equivalent circuit by using SPICE model of thermoelectric devices. The embedded cooler attached between the die chip and metal plate can offer the possibility of thin film active cooling for the COB direct assembly. We proposed a driving method of TEC by using pulse width modulation technique. The optimum power to the TEC is simulated by using a SPICE model of thermoelectric device and passive components representing thermal resistance and capacitance. The measured and simulated results offer the possibility of thin film active cooling for the COB direct assembly.

• Journal of Electrical Engineering and Technology
• /
• 제11권1호
• /
• pp.125-134
• /
• 2016

We propose an efficient high voltage level shifter for a high side Buck converter driving a light-emitting diode (LED) lamp. The proposed circuit is comprised of a low voltage pulse width modulation (PWM) signal driver, a coupling capacitor, a resistor, and a diode. The proposed method uses a property of a PWM signal. The property is that the signal repeatedly transits between a low and high level at a certain frequency. A low voltage PWM signal is boosted to a high voltage PWM signal through a coupling capacitor using the property of the PWM signal, and the boosted high voltage PWM signal drives a p-channel metal oxide semiconductor (PMOS) transistor on the high side Buck converter. Experimental results show that the proposed level shifter boosts a low voltage (0 to 20 V) PWM signal at 125 kHz to a high voltage (370 to 380 V) PWM signal with a duty ratio of up to 0.9941.

• 전기학회논문지P
• /
• 제60권2호
• /
• pp.72-75
• /
• 2011

In this paper, the voltage across the LED system supplied by positive voltage of power supply system the power consumption of the LED itself, and uses a lot of transformers and analog devices, such as converter startup problems and constant temperature even when the voltage driving abnormally LED current in the destruction caused by the flow of a lot of problems can occur. In this paper, we obtain the technology of consistent current using PWM(pulse width modulation) mode in order to minimize analog devices and eventually discuss the technology to develop consistent output converter using power drive IC.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(1)
• /
• pp.308-311
• /
• 2004

A novel single-stage power factor corrected (PFC) drive for switched reluctance motor (SRM) is presented to achieve sinusoidal, near unity power factor input current. The proposed PFC SRM drive has no additional active switch. And a single-stage approach, which combines a DC link capacitor used as do source and a drive used for driving the motor into one power stage, has a simple structure and low cost. The characteristics and validity of the proposed circuit will be discussed in depth through the experimental results.

• Journal of Welding and Joining
• /
• 제15권1호
• /
• pp.81-91
• /
• 1997

In this study, a magnetic sensor to make use of eddy current was developed to detect the weld seam of butt joint in the sheet metal arc welding. This system consist of the sensor device for detecting the weld line, the servo control device for driving the weld torch movement and the control unit. A signal processing was applied to smooth the output signal of the sensor. The weld joint was determined by using a 1st order differential method. To improve tracking accuracy of the system, moving average method which has an effect of proportional and weighted integral control was applied to a series of the weld joint positions obtained above. The weld line for tracking was generated by using data regeneration algorithm. Based on these results, each servo motor was controlled by pulse generator. From experimental results, it was revealed that this system has excellent detecting ability for weld line and seam tracking ability.