• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.5 s.113
• /
• pp.70-77
• /
• 2005

The development of printable Hanji is regarded as an important work to create a new demand of Hanji in information-oriented era. Hanji has rougher surface, huger absorption of ink and lower optical properties and printabilities than common printing papers. Improving those shortcomings of Hanji is required to be printable Hanji. Sizing and calendering have known as a way to make properties of paper good. Accordingly, this research was performed to find out useful sizing agents for reforming its drawbacks. Four sizing agents (CMC, com starch, PVA, AKD) were used in this research. The optical properties and the printabilities of sized Hanji were tested. The obtained results were as follows. Based on concentration, each sizing agent was prepared. These were CMC(0.5, 1, $1.5\%$), corn starch(1, 2, $3\%$), PVA(1, 5, $10\%$), AKD(0.5, 0.1, $0.15\%$) respectively. After sizing, we performed calendering treatment with pressure of 0.5, $1\;kgf/cm^2$. All the sizing agents and calendering treatment improved the properties of Hanji to some extent. Particularly, com starch was good for gloss. In case of printability, $1\%$ AKD with $1\;kgf/cm^2$ was recommendable for typography ink density, $3\%$ com starch with $0.5\;kgf/cm^2$, inkjet ink density, $2\%$ com starch with $0.5\;kgf/cm^2$, inkjet ink girth. PVA and AKD without calendering were counter-effective agents for inkjet ink density. Printable Hanji is required to have not only better surface strength enough to appear non-picking, higher ink density and lower show-through than base paper but also the lowest ink girth in comparison with base paper. When referring to them, efficient sizing agents were regarded as $0.1\%$ AKD with $1\;kgf/cm^2$, calender pressure, for typography printing and $2\%$ com starch with $0.5\;kgf/cm^2$, calender pressure, for inkjet printing.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.51-61
• /
• 2012

The new alkali pulping process combined with electron beam treatment was applied to utilize hemp bast tissues as a new valuable fibrous resource. Hemp bast tissues have some chemical properties with high lignin contents and holocellulose not to be defiberized by alkali pulping only, compared with the bast tissue of paper mulberry. To make up for the weakness of traditional alkali pulping process, electron beams were directly irradiated into the swelled bast tissue of hemp in NaOH solution and distilled water, and then facilitated the defiberization of hemp bast tissues. The papermaking from hemp bast fibers manufactured by the combination pulping process showed good apparent density, formation structure and air permeability, and had some mechanical properties with lower tensile, tear, burst strength and folding endurance. It is finally concluded that the combination pulping process with electron beam treatment could be suggested a new alternative for non-woody fibers.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.3
• /
• pp.66-70
• /
• 2009

Paper cultural heritages usually experienced the chemical and the physical deterioration because of various factors including preservation environment and the property of their materials. General restoration technology for paper cultural heritages is the lining. The application of the lining paper and the lining technology has varied depending on researcher's experiences. Therefore, each lining material and technology must be evaluated to develop a standard guide for preservation and restoration of paper cultural heritages. To date, various analysis techniques using lining paper, in terms of their materials, have been applied to analyses of causes and condition of damages, but it is difficult to develop a standard restoration treatment method of paper cultural heritages because it varies by their material. The Hanf, is made frrr the mulberry, is generally used for the lining in Korea.edt is required that the cr, in terms properties and general properties of Hanf, is used for lining papers, are evaluated to develop a standard guide for their restoration.ed this study, the general properties of several lining papers(Hanf), especially dimensave bility, were evaluated as part of the standardization of lining papers. The result have varied depending on the pulping chemical and the manufacturers. the basis weight, thickness and tensale strength of lining papers is bigger the paper treated by natural ash than the paper treated by sodium carbonate.ed case of formation, folding endurance, and dimensave bility, the paper treated by sodium carbonate showed better properties than those of the paper treated by natural ash.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.5
• /
• pp.79-87
• /
• 2014

The enrichment with nutrients in rivers and lakes becomes serious problems in Korea. As the environmental friendly solution, the phytoremediation are getting more attention and the water hyacinth could be a strong candidate plant for this. Water hyacinth is a free floating freshwater plant proven to be a effective plant used for a purification of a polluted lakes, sewage wastewater, and livestock wastewater. The biggest obstacles for application of water hyacinth in Korea could be the disposal of the water hyacinth before winter, because there is no feasible use for the water hyacinth until now. In this study, the characteristics of water hyacinth were deeply investigated for providing background data to develop appropriate application of the water hyacinth. The water hyacinth was fractioned three parts, leaf, air blader, root of which morphological properties were evaluated with microscope and field emission scanning electron microscope (FE-SEM). The water contents of each parts of the water hyacinth were 87% for leaf, 96.5% for air bladder, 94.6% for root. The chemical compositions of each parts were also measured and showed around 29% of hot water extract in leaf and air bladder, 42% holocellulose for leaf, 47% holocellulose for air bladder. The application of water hyacinth biomass without root parts to papermaking provided bulkier structure, but the tensile strength was decreased.

• Journal of Korean Society of Forest Science
• /
• v.26 no.1
• /
• pp.57-65
• /
• 1975

This study was carried out to examine the effect of manufacturing factors on physical properties of hardboard (S.I.S) made from the juvenile wood of sycamore (Platanus orientalis L.) The results obtained may be summarized as follows: 1. The difference among the yields of pulp treated with preheat time (defibrate condition) was significant in those of treatments. There was no difference in the yield of pulp treated with defibrate time. The yields of pulp on the tree age classes were shown the difference by 2<4<6<8 years. 2. The specific gravities of hardboard that were treated with hot pressing conditions showed us significantly in those of treatments. There was no difference on the specific gravities among hardboards, treated with resin and wax contents. But in all cases of the specific gravities satisfied the standard which specified the KS F 3203 (Hardboard) 3. The moisture contents of hardboard satisfied the standard which calls for 13-percent below. There were difference in moisture contents between hardboard, treated with preheating time, resin and wax contents and hot pressing conditions. And the moisture contents of hardboard on the tree age classes showed the difference by 2<4<6<8 years. 4. The water absorption and thickness swelling of hardboard treated with defibrations, resin and wax contents, and hot pressing conditions were significant in those of treatments. And the water absorption and thickness swelling of hardboard on the tree age classes showed us the significant difference by 8<6<4<2 years. 5. The difference among the flexural strength in using tested three conditions showed us the difference by defibration$200kg/cm^2$) of hardboard, it is likely to be recommened that the juvenile wood of sycamore is valuable for the raw materials of hardboards.

• Archives of Plastic Surgery
• /
• v.37 no.5
• /
• pp.650-658
• /
• 2010

Purpose: In the case of repair for far distal parts of FDP (Flexor digitorum profundus) division, the method of either pull-out suture or fixation of tendon to the distal phalanx is preferred. In this paper, the results of a modified loop suture technique used for the complete division of FDP from both zone 1a and distal parts of zone 1b in Moiemen classification are presented. Methods: From July 2006 to July 2009, the modified loop suture technique was used for the 10 cases of FDP in complete division from zone 1a and distal parts of zone 1b, especially where insertion sites were less than 1 cm apart from a tendon of a stump. In a suture technique, a loop is applied to each distal and proximal parts of tendon respectively. Core suture of 2-strand and epitendinous suture are done with PDS 4-0. Out of 10 patients, the study was done on 6 patients who were available for the followup. The average age of the patients was 49.1 years (in the range from 26 to 67). 5 males and 1 female patients were involved in this study. There were 3 cases with zone 1a and distal parts of zone 1b. The average distance to the distal tendon end was 0.6 cm. There were 5 cases underwent microsurgical repair where both artery and nerve divided. One case of only tendon displacement was presented. The dorsal protective splint was kept for 5 weeks on average. The results of the following tests were measured: active & passive range of motion, grip strength test, key pinch and pulp pinch test. Results: The follow-up period on average was 11 months, in the range from 2 to 20 months. There was no case of re-rupture, but tenolysis was performed in 1 cases. In all 6 cases, the average active range of motion of distal interphalangeal joint was 50.8 degree. The grip strength (ipsilateral/contralateral) was measured as 88.7% and the pulp pinch test was 79.2% as those of contralateral side. Flexion contracture was presented in 2 cases (15 degree on average) and there was no quadrigia effect found. Conclusion: Despite short length of tendon from the insertion site in FDS rupture in zone 1a and distal parts of zone 1b, sufficient functional recovery could be expected with the tendon to tendon repair using the modified loop suture technique.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.1
• /
• pp.73-83
• /
• 1997

Most of the materials used in various industrial fields and also in our daily life are multi-component materials or composite materials, and it is well known that there are many cases where adhesion between the constituents within the bonded systems plays an important role. There are various types of performance evaluation tests for the bonded materials, among which tests for evaluating the bond performance under various conditions may be regarded as the most interesting ones for those engaged in work related to adhesion. I have studied on the mechanism of adhesion form the rheological standpoint with my colleagues, including some students from Korea, and I am very happy to be able to have a talk on some of our research works. In Japan, the so-called "adhesives" are usually classified into two categories;adhesives and pressure sensitive adhesives (PSA). Adhesives are the materials which solidify after bonding and are after used as the structural adhesives because the adhesive strength is comparatively strong. On the other hand, the pressure sensitive adhesives never solidify and are used as PSA tapes, labels or decals. About the adhesives, we have examined the dependence of adhesive strength(shear, tensile, peel) upon both temperature and rate of deformation, and found out some empirical rules which are applicable to most of the adhesive systems. We have also developed a simplified theory of adhesion, which is deseribed in terms of mechanical equivalent mode1 and a few failure criteria. Although some of the common rules can be accounted for according to this theory, it must be pointed out that a fracture mechanical approach ms inevitable especially in the region where the meehanical relaxation time of the adhesive is extremely large [W. W. Lim and H. Mizumachi]. About the pressure sensitive adhesives, we have studied on the PSA performance (peel, tack, holding power) as a function of both the viscoelastic properties and surface chemical properties of the materials, and found out some rules, and again we have developed a theory which deseribes the mechanism. And in addition, we have studied on the miscibility between linear polymers and oligomers, because PSA is generally manufactured by blending gums and tackifier resins. Many phase diagrams have been found and some of them have been analyzed on thermodynamic basis, and it became evident that the miscibility is a very important factor in PSA [H. J. Kin and H. Mizumachi]. In this presentation, I want to emphasize the fact that the adhesion performance is closely related to the structure/property of the adhesives.adhesives.

• Korean Chemical Engineering Research
• /
• v.44 no.6
• /
• pp.602-608
• /
• 2006

Carbon fiber (CF) reinforced papers using polyacrylonitrile (PAN) based CF and wood pulp were prepared by varying the lengths and the concentrations of CF, and the basis weight of paper to investigate adhesive state between CF and pulp, and physical properties and electrical conductivity of the paper. The reinforcement was caused by physical entanglement and adhesion at the interface of the different fibers rather than by chemical bonds. The tear strength and the thickness of the paper increased as increasing the concentration of CF, while the tensile and the burst strength of the paper decreased. The improved dispersion of CF in the paper was obtained from mixing shorter CF, but the maximum electrical conductivity of the paper was gained from mixing 10 mm chopped CF. The electrical conductivity of the paper increased sharply from 2 wt％ to 8 wt％ of CF showing S-curve, and increased linearly as increasing the basis weight of the paper. Therefore, in order to improve the electrical conductivity and the physical property of the paper, the increase of basis weight of the paper is also important as the increase of CF content in the paper.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.3
• /
• pp.38-45
• /
• 1998

Soil and water contamination caused by the abundant use of agricultural chemicals including herbicides and fertilizers draws public concerns since these chemicals may pollute the agricultural lands as well as the food products grown on these lands. As a method to reduce the use of agricultural chemicals mulching with thin plastic film has been commonly practised for many years. Although use of the plastic film for mulching is very effective in preventing the growth of weed, it is almost impossible to remove all of the plastic film from the agricultural land and the remaining film eventually contaminates the soils. Therefore, it is very imperative to develop a mulching material that decomposes completely to prevent soil pollution problems and to enhance the competitive edge of domestic agriculture. Mulch papers are believed to have many positive characteristics in preventing problems caused by the plastic mulch film since it decomposes completely after use. However, the basis weight of mulch papers needs to be reduced to improve its handling properties and to reduce the raw material costs of pulps. In this paper the possibilities of using domestic old corrugated containers in producing mulch papers were examined. Also use of unbleached softwood kraft pulps and dry strength additives were exploited along with two-layered sheet forming technology in decreasing the basis weight of the mulch paper. Results showed that reduction of 20g/$m^2$ of basis weight of mulch paper was possible by the appropriate raw material selection and application of strength resin. To use the mulch papers in paddy fields, however, further research to improve its durability should be pursued.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.47 no.2
• /
• pp.205-212
• /
• 2020

The purpose of this study is to evaluate the validity of primary anterior zirconia crown made with Computer Aided Design/Computer Aided Manufacturing (CAD/CAM) technology by analyzing fracture strength and translucency parameter. Zirconia crown was designed with CAD software, using 3D scanned data of #61 tooth model. Crown fabrication was performed with CAM machine using zirconia block. Zirconia crowns were divided into 3 groups according to thickness(0.3, 0.5, and 0.7 mm), and fracture strength was compared with 1.0 mm thickness of resin strip crown. The compressive force was applied with universal testing machine at 30° along the incisal edge at increments of 1 mm/min. For translucency evaluation, 0.3, 0.5, and 0.7 mm thickness of zirconia specimens were fabricated and translucency was measured with spectrophotometer. Among zirconia groups, there was a significant increase in fracture strength as thickness increased (p < 0.05). The fracture strength of zirconia crown was significantly higher than resin strip crown in all groups (p < 0.05). Translucency parameter was highest in 0.3 mm group, and significantly decreased as thickness increased to 0.5 and 0.7 mm (p < 0.05). Thin primary anterior zirconia crown can be designed and fabricated according to individual needs by using CAD/CAM. Restoration with thin crown would reduce the amount of tooth reduction, risk of pulp exposure, and make more esthetic restoration possible.