• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.2
• /
• pp.32-40
• /
• 2001

It is desirable to reduce the amounts of fresh water and reuse the recycled water in papermaking process. In an attempt to improve the efficiency of recycling water refining treatment and to enhance the productivity of OCC recycling mill, up flow anaerobic sludge blanket(UASB) reactor was developed and introduced to Korea recently. In order to maximize the operating efficiency and minimize the adverse side effects it is imperative to estimate and evaluate the total effects of new system, UASB on the whole OCC recycling process. This study was carried out with a view to investigate the effects of the high temperature and alkalinity of process water on the quality ad productivity of testliner of OCC recycling mill which is equipped with UASB reactor and almost closed. Another object of this study was searching for the best available use of UASB treated process water. The results were as follows; Reuse of UASB treated water characterized with high temp and alkalinity was useful to improve the strength and drainage properties of recycled OCC owing to its good points of promoting OCC disintegration and reducing the calcium hardness of process water. However, it might not be avoidable to induce the increase of dissolved solids in process water in accordance with direct introducing of UASB treated water into the former stage of OCC stock preparation. So it would be advisable to adopt the UASB treated water in the stage of clean, screened OCC stock.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.1
• /
• pp.46-53
• /
• 2002

This study was carried out to analyze the effects of preservation temperature and relative humidity to the physical properties of corrugated fiberboard boxes for fruit and vegetable packaging. The preservation temperature did not affect severely to physical properties of corrugated fiber-board. Relative humidity was a major cause of corrugated fiberboard box quality deterioration. The burst and compressive strengths of experimental boxes measured with Mullen high pressure tester and tong crush tester were decreased gradually as relative humidity increased from 55% to 75%. But, the strength properties slightly decreased relative humidity at 75% or higher. This tendency was the greater for single wall (SW) corrugated fiberboard box than that for double wall (DW). It is suggested that development of the water-resistant corrugated fiberboard and box be needed that can be used under the condition of low temperature and high moisture content, which are being employed in the cold chain system.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.3
• /
• pp.50-58
• /
• 2005

It is generally known that paper industry is the second largest industry in the use of process water, and also have the highest environmental impact load in the contaminant sources. Paper is produced from the mixtures composed of 1% fibrous raw materials and 99% water. The optimum use of process water effects on the quality properties of paper and the environmental impact load of waste water treatment. In this research, the kinds of fibrous raw material & additives used in the paperboard production line were investigated, and the quantification of environmental loads and the environmental effects of process water on COD potential were evaluated. The NBDCODs were also analyzed from process water by the method of waste water treatment in paper mill and applied for the optimum use of recycling water, and zero effluent process. In the fibrous raw materials, KOCC caused the highest COD potentials, and sack paper & UKP was comparatively low. The NBDCOD of KOCC largely reduced after biological treatment because of easily biodegradable properties, but AOCC contained non-biodegradable materials. In chemical additives, COD was high in turns of rosin>starch>deaeration agent>dye, NBDCOD greatly reduced in starch and deaeration agent. In the case of 2 kinds of paperboard product, the COD potentials was mainly high in starch, AOCC and KOCC.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.3
• /
• pp.1-8
• /
• 2005

Increase in the utilization rate of recycled paper and closing level of papermaking system increased the problem associated with stickies that include decrease in process runnability and product quality. It is required to establish a process for removing the micro stickies to solve the problems associated with stickies. In this study, the application of flotation process as a method to remove micro stickies was examined. Model micro stickies (MMS) were prepared using microcrystalline cellulose (MCC) and pressure sensitive adhesives (PSA), and the influence of three nonionic surfactants on the removal efficiency of MMS from flotation process was examined. Also the effect of surfactants on the deposition of micro stickies that remaining in the papermaking wet end onto wire was examined. Removal efficiency of MMS by flotation was increased when the proportion of nonionic surfactant with propylene oxide (PO) type hydrophilic tail was increased and stock pH was 7. It was suggested that this nonionic surfactant minimized the increase of surface energy of hydrophobic MMS. The MMS with high hydrophobicity remaining in the papermaking system, however, would cause more serious deposition problems on papermaking wet end. Therefore, it is of great importance to increase the removal efficiency of MMS in flotation process for the prevention of papermaking system contamination caused by stickies deposition.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.3
• /
• pp.30-36
• /
• 2016

This study was conducted to investigate the influence of the changes in handsheet structure by beating, wet pressing and the addition of wood flour spacer on the water absorption and the moisture absorption properties. The higher beating treatment of BKP resulted in the denser structure of handsheet samples, which leaded to the lower water and moisture absorption. The wet pressing showed the similar effects by reducing the bulk of handsheets. In case of the handsheet samples with similar bulk structure made of different beaten pulps, the severer beating treatment increased the water absorption and the moisture absorption. The addition of the wood flour spacer resulted in the higher bulk following the higher water and moisture adsorption. Since the water and the moisture absorption properties of paper products could greatly affect on not only the product quality but also the process runnability, the control of the water response of paper product has been considered as very important technology. The results of this study might be useful for control of water and moisture absorption properties of paper products.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.5
• /
• pp.1-13
• /
• 2013

This study found fit optimum C, M, Y, K solid density and $CIEL^*a^*b^*$ value to paper & ink as well as check about printing machine state for color management in H-UV waterless off-set printing first. These values applied to GRACoL G7 calibration method. This method is one of color standard management method of printing. GRACoL G7 calibration method is possible stable tone reappearance by controlling gray balance by NPDC(Natural Printing Density Curve). Also, this study used values to make device profile as result that is gotten by application of GRACoL G7 calibration method. This profile was applied to CMS(Color Management System) of H-UV waterless off-set printing, and the result was possible by color management that correspond in printing quality standard of ISO 12647-2 and GRACol 2006 specifications.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.5
• /
• pp.44-48
• /
• 2013

Ultrasonic treatment of KOCC was tried to explore the possibility for improvement of KOCC quality as a raw material for making industrial packaging paper and paperboard. The effect of pH, stock consistencies and treatment times on the ultrasonic response of KOCC were investigated. WRV, apparent density, tensile index and burst index were improved as pH of KOCC slurry is increased. However highest tear index and stiffness were obtained at pH 8. It was also found that the highest WRV and strength properties could be obtained at 0.5% of KOCC consistency during ultrasonic treatment. WRV and most strength properties were improved with ultrasonic treatment time. It was found that ultrasonic treatment can be used as a useful mean for KOCC modificaton.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.2
• /
• pp.26-34
• /
• 2000

Understanding the nip geometry and heat transfer phenomena of soft nip calenders, which has been used in the production of newsprint and coated papers for many years, is very important since improper setting of soft nip calendering conditions causes deterioration of paper quality and productivity. In this study theoretical analysis on nip pressure and heat transfer phenomena in the nip of soft nip calenders has been made. The variables examined were calendering pressure, surface temperature of the heating roll, nip residence time and ingoing sheet moisture, By measuring nip widths and maximum nip pressure with Prescale film at a normal temperature, accurate line load has been obtained. With this line load, nip pressures at different temperature and nip widths were calculated. Results showed that as temperature increased, nip widths increased and nip pressures decreased. Equations derived for the heat conduction phenomena in soft nip calender nip were derived based on the semi-infinite plate and finite difference method and were used for the analysis of heat transfer within the nip. Temperature profiles in z-direction of paper within the nip were obtained. Finite difference method allowed more accurate analysis of the heat transfer in the calender nip. In this study newsprint and coated paper were considered as a single plate and two-layer plate consisted of sheet and coating layers, respectively. Heat trans-fer to paper increased as heated roll surface temperature and nip residence time were increased.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.4 s.117
• /
• pp.41-46
• /
• 2006

Printed mottle of coated paper is one of the most common but the most difficult problem in offset printing. Printed mottle is caused by an uneven penetration of Ink into the paper, binder migration, etc. For a high quality printing, development of new paper coating technologies to prevent print mottle is required. So for, the study of solving printed mottle is coated paper absorption controlled by base paper sizing and coating layer binder migration control. As a results, printed mottle has improved in coated paper. But printing is worked by interaction of printing ink, coated paper and printing pressure, then we need to understand of interaction printing work and coated paper. This research focused on a way of improving printed mottle by investigating various printing conditions such as ink dispersion, nip condition and amount of ink transfer using IGT printability tester.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.3
• /
• pp.7-13
• /
• 2010

KOptimization and control of wet-end process provide a key solution to improve paper quality and production efficiency at the same time. Wet-end of paper machine is to determine three important influencing factors of papermaking i.e., retention, drainage and formation. Good formation of paper could be made at the cost of deteriorated retention or drainage. In the same manner increase of retention aid could cause the bad formation of paper. It is very important to find a proper retention chemical which may satisfy one of three factors without the sacrifice of other two. Laboratory scale analyzing or screening chemical additives of wet-end was reported in this study based on RDA sheet molding. Different from the conventional test method, simultaneous consideration of three important wet-end properties could be made by RDA and consequently more reliable prediction of actual paper machine wet-end could be expected.