• 펄프종이기술
• /
• 제47권4호
• /
• pp.136-143
• /
• 2015

It is well known that the use of PCC as a filler for printing paper making brought about the serious deterioration of strength properties of paper, although PCC could be helpful to reduce the energy consumption. The use of modified PCC with NCC was tried to solve and/or reduce the strength deterioration problem. NCC was prepared from SwBKP by the acid hydrolysis. There was no significant changes in chemical properties and crystalline structure. However the cyrstallinity of NCC was higher than those of SwBKP. The different dosage of NCC was applied to modify the properties of PCC. 0.1% of NCC dosage was enough to improve ash retention and paper properties. The use of modified PCC with NCC as a filler improved ash retention, bulk, opacity and formation without the serious deterioration of strength properties. Thus the use of modified PCC with NCC might be helpful for not only reduction of energy consumption but also increase of filler dosage without the significant sacrifice of strength properties by the optimization of retention system.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.1
• /
• pp.129-136
• /
• 2006

Although cleaner and cheaper deinking of ONP could be performed at the neutral or low alkaline condition excessive loss from froth-flotation is unavoidable and so reduction of alkali or caustic soda dosage sacrifices recycling yield. Now the new trade-off regarding alkali dosage versus flotation yield is urgently required in order to set the optimized neutral or low alkaline deinking process of ONP. Lipase from Thermomyces Lanuginosus has an effect on desizing and deacetylation reaction and it could be applied to the stock of pre flotation secondary stage in order to reduce the flotation reject without the sacrifice of optical properties of flotation accepts. Instead of inorganic base, lipase could be applied as a biochemical catalyst for the selective modification of valuable hydrophobic particles in deinking stock, for example cellulose fines and inorganic fillers covered by hydrophobic additives or contaminants. When the enzymatic hydrolysis of ester bond could be made on the surface of hydrophobic particulates, unwanted float of fine particles could be prevented. Now the enhancement of flotation selectivity or the modification of the hydrophobicity of deinking stock is expected to be promoted by the enzymatic pre treatment. And the reduction of recycling cost with the saves of raw material, recovered paper would be possible as a result.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.1
• /
• pp.43-49
• /
• 2006

The surface and pore structure of cellulose fibers have a significant impact on the properties and performance in applications. Cellulase enzymatic hydrolysis of cellulose fibers can result in changes to the surface and pore structure thus providing a useful tool for fiber modification. This research characterizes these changes using various test methods such as fiber dimension, water retention value, hard-to-remove water content, freezing and non-freezing bound water content, polymer adsorption, and crystallinity index. For a high-dosage enzyme treatment (0.10 g/g), the fiber length was significantly decreased and the fibers were 'cut' in the cross direction, not in the axial direction. The swelling capacities as measured by the WRV and HR water content increased for the high-dosage treatment. Three independent measurements (non-freezing bound water, polymer adsorption, and crystallinity index) are in good agreement with the statement that the amorphous regions of cellulose fibers are a more readily available substrate relative to crystalline regions. Based on the experimental results obtained herein, a model was proposed to explain surface and pore structure modification of cellulose fibers via enzymatic treatment.

• 펄프종이기술
• /
• 제46권6호
• /
• pp.50-55
• /
• 2014

An oxidized starch was modified for surface sizing via etherification and esterification. Propylene oxide (PO), sodium monochloroacetate (SMCA), and acrylonitrile (AN) were used as etherification, and vinyl acetate monomer (VAM), maleic anhydride (MA), fumaric acid (FA), and itaconic acid (ITA) were used for esterification. Esterification and etherification of starch decreased both Brookfield viscosity and Brabender viscosity substantially even though the solids level was increased by 2% from 14 to 16%. Surface sizing performance of starches in tensile strength, stiffness and compressive strength was improved by esterification and etherification of the oxidized starch. Especially, SMCA etherification was found to be the most effective modification method.

• Archives of Plastic Surgery
• /
• 제36권5호
• /
• pp.674-677
• /
• 2009

Purpose: Typical cross finger flap is still a good method for reconstruction of fingertip injuries. However, it is necessarily followed by great loss and aesthetically unpreferable result of donor finger. Hereby, we introduce a modification of cross finger flap with reduction pulp plasty and full thickness skin graft, with which we could reduce the defect size of injured fingertip and donor site morbidity at the same time, without any need for harvesting additional skin from other part of hand. Method: This method was performed in the patients with fingertip injuries of complete amputation or in case of loss of fingertip due to necrosis after replantation. Firstly, reduction pulp plasty was performed on the injured finger to reduce the size of defect of fingertip. Additional skin flap was obtained from the pulp plasty. Secondly, cross finger flap was elevated from the adjacent finger to cover the defect on the injured finger. At the same time, defect on the donor finger produced by the flap elevation was covered by full thickness skin graft with the skin obtained from the pulp plasty of injured finger. Results: Flap and graft survived without any necrosis after surgical delay and flap detachment. All of them were healed well and did not present any severe adversary symptoms. Conclusion: Cross finger flap with reduction pulp plasty and full thickness skin graft is an effective method that we can easily apply in reconstruction of fingertip injury. We think that it is more helpful than the usual manner, especially in cases of children with less soft tissue on their fingers for preservation and reduction of the morbidity of donor finger.

• 생체재료학회지
• /
• 제22권4호
• /
• pp.346-351
• /
• 2018

Background: Carbonate apatite ($CO_3Ap$) and silica-calcium phosphate composite (SCPC) are bone substitutes with good prospect for dental application. SCPC creates a hydroxyapatite surface layer and stimulate bone cell function while, $CO_3Ap$ induce apatite crystal formation with good adaptation providing good seal between cement and the bone. Together, these materials will add favorable properties as a pulp capping material to stimulate mineral barrier and maintain pulp vitality. The aim of this study is to investigate modification of $CO_3Ap$ cement combined with SCPC, later term as $CO_3Ap-SCPC$ cement (CAS) in means of its chemical (Calcium release) and physical properties (setting time, DTS and pH value). Methods: The study consist of three groups; group 1 (100% calcium hydroxide, group 2 $CO_3Ap$ (60% DCPA: 40% vaterite, and group 3 CAS (60% DCPA: 20% vaterite: 20% SCPC. Distilled water was employed as a solution for group 1, and $0.2mol/L\;Na_3PO_4$ used for group 2 and group 3. Samples were evaluated with respect to important properties for pulp capping application such as pH, setting time, mechanical strength and calcium release evaluation. Results: The fastest setting time was in $CO_3Ap$ cement group without SCPC, while the addition of 20% SCPC slightly increase the pH value but did not improved the cement mechanical strength, however, the mechanical strength of both $CO_3Ap$ groups were significantly higher than calcium hydroxide. All three groups released calcium ions and had alkaline pH. Highest pH level, as well as calcium released level, was in the control group. Conclusion: The CAS cement had good mechanical and acceptable chemical properties for pulp capping application compared to calcium hydroxide as a gold standard. However, improvements and in vivo studies are to be carried out with the further development of this material.

• 펄프종이기술
• /
• 제48권3호
• /
• pp.14-22
• /
• 2016

Pulping is a stage that can change fibrous raw materials into pumpable slurry. Recovered paper can be defibrated to individual fibers by shear stress generated by rotation of a rotor and water. Disintegration of recovered paper is more complicated than that of chemical pulp. When disintegration of recovered paper is poor, screening and cleaning efficiency will be worse and properties of paper will also be deteriorated. Therefore, pulping is an important treatment for improvement of availability of recovered paper and process runnability. In this study, degrees of disintegration of KOCC obtained from a linerboard mill was analyzed with a pilot-scale screen. Flake removal of KOCC slurry was performed by a pilot screen. Simple pumping action gave a positive effect on disintegration of KOCC. After pumping for 10 minutes, paper strength increased without the change of water retention value and fibrillation of KOCC slurry. This phenomena can be explained by modification of hornified surface of KOCC fibers by shear stress generated by pumping. Consequently, disintegration efficiency of KOCC can be enhanced by control of retention time at pulper or an agitation power at chests of papermaking process.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 Proceedings of Pre-symposium of the 10th ISWPC
• /
• pp.115-119
• /
• 1999

During mechanical pulp production and blcaching wood components, such as extractives, carbohydrates and lignin are dissolved and dispersed into the process waters. These components are called dissolved and colloidal substances(DCS). DCS can accumulate during water circulation and can in turn affect paper machine runnability and also the strength and optical properties of the paper. In this work DCS fraction origination from TMP process were treated with enzymes acting on triglycerides. glucomannans, and lignin and the effect of enzymatic treatments on the water composition as well as sheet properies were evaluated. Lipases were found to modify the chemical structure of the extractives resulting in more hydrophilic fibre surface and subsequent improvement in the sheet strength properties. Mannanase treatment, on the other hand, destabilized pitch. As a result, aggregation of pitch to the fibres was observed which in turn resulted in impaired strength properties. Laccase could effectively polymerize lignans and the reaction products seemed to be sorbed onto the fibres.

• 펄프종이기술
• /
• 제47권2호
• /
• pp.42-52
• /
• 2015

In this study, cellulose nanofibrils (CNF) were modified through carboxymethylation or TEMPO-mediated oxidation and their effects on ionicity and characteristics of sheet, film, and foam were investigated. Carboxymethylation was carried out on pulp fibers as a pre-treatment before preparation of CNF. The gel-like and translucent CNF hydrogel was obtained by grinding of carboxymethylated cellulose fibers. Carboxymethylated CNF film and freeze dried sheet showed higher transparency than that of untreated CNF. The CNF sheet with high strength and the CNF foam without large ice crystals were obtained by using the carboxymethylated CNF. TEMPO-mediated oxidation was carried out as a post-treatment of CNF. The zeta potential and charge demand of TEMPO-oxidized CNF were increased with an increase in oxidation time and addition amount of NaClO. The density of sheet made of TEMPO oxidized CNF was increased with the amount of oxidizing agent. The TEMPO oxidized cellulose nanofiber (TOCN) which was obtained from supernatant after centrifugation could be converted to transparent film.

• 펄프종이기술
• /
• 제36권4호
• /
• pp.41-48
• /
• 2004

To make a basepaper for multipurposed seed paper, old news print (ONP) and mixed office waste paper (MOW), modified and unmodified with a commercial cellulase, were investigated. Each handsheet was applied with different chemicals such as insecticides, germicides and herbicides. The interactions behaviors of chemicals used with base papers were evaluated by means of the contents of chemicals impregnation and dissolving behaviors in water and soil. The ONP and MOW treated with the cellulase had higher impregnation and dissolving capacities in both water and soil than untreated ONP and MOW. However, the modified ONP showed lower impregnation and dissolving capacities compared to the modified MOW. The content of impregnation of chemicals would be affected with the degree of microfibrils produced by the modification treatment. Otherwise, dissolving capacities of chemicals depend on the affinity of the residual lignin in the paper.