• Korean Journal of Rural Living Science
• /
• v.6 no.1
• /
• pp.25-30
• /
• 1995

This study was designed to obtain the basic data developing the UV ray protective garments for the plastichouse workers. Two subjects were volunteered for 1hr. wear test in plastic house, and the ensembles was composed of one of three kinds blouse (UV blocking blouse, polyester/cotton 47/53 blouse, and polyester blouse), shorts, sleeveless undershirts, pants and socks. The measurements were rectal temperature, skin temperature, microclimate inside clothing, subjective sensation, and the colour difference of UV sensor. The results were as follows: 1. Microclimate especially, temperature inside clothing of polyester blouse was the highest among the garments. And UV-proof polyester blouse showed the lower mean skin temperature and microclimate than others. Showing the highest sweat volume. 2. No significant difference on UV ray blocking function among 3 kinds of garment was shown. 3. We could conform that in spring for the plastic house wぉw s garment low thermal insulating value and wide covering area were more important factors than UV blocking function of fabric.

• Korean Journal of Human Ecology
• /
• v.13 no.5
• /
• pp.777-785
• /
• 2004

We intend to analyze reasons for low acceptability of protective clothing in pesticide-spraying farmers in Korea, and to use the information for designing new clothing with better acceptability. To understand the attitude of farmers toward wearing protective clothing during spray, a survey was performed on 256 farmers. It is evident that the stress, which is caused by inadequate body temperature regulation, and its accompanying physiological responses are two of the leading factors for the low acceptability of protective clothing. Although the cost of clothing is not an important factor currently, low cost clothing is desirable in the future. Fancy of design is unimportant for new clothing. The results are discussed in conjunction with a desirable research focus for new types of protective clothing. Efforts should be made to ameliorate thermal stress through protective material development and garment design.

• Fashion & Textile Research Journal
• /
• v.17 no.4
• /
• pp.635-645
• /
• 2015

This study analyzed the range of motion of upper body in different configurations of firefighters' protective clothing and equipment. The purpose of this study was to understand the influence of firefighters' protective clothing and equipment over upper body motion in order to improve design of firefighters' protective clothing and equipment. 12 firefighters' upper body range of motion was analyzed while performing standing and walking trials in five different garment configurations including turnout ensemble, fire boots and the self-contained breathing apparatus. Analysis of upper body range of motion included spinal joints of L5S1, L4L3, T1C7, and C1Head. During standing trials, garment configurations caused a significant difference in range of motions at joints of L5S1, L4L3, T1C7, and C1Head. Analysis on the mean of range of motions at L5S1 and L4L3, showed that firefighters' waist bent forward significantly to a greater extent while they wore a self-contained breathing apparatus. A significantly increased range of motion was found for T1C7 and C1Head while carrying a self-contained breathing apparatus, which indicated an increase in the extension of the trunk and neck backward to stand upright and look squarely. A significant difference in range of motion was also found for L5S1 and L4L3 during walking trials.

• International Journal of Human Ecology
• /
• v.13 no.1
• /
• pp.117-128
• /
• 2012

This study compares the net effect of wearing different shoulder/arm armor systems on garment impediment perception and wearer acceptability. Two independent variables in this study were armor systems and shoulder/ arm movements. There were four armor systems of control garment and arm armor systems A, B, and C as well as five types of arm/shoulder movements, (shoulder flexion, should extension, shoulder abduction, shoulder horizontal flexion, and shoulder horizontal extension). Ten male volunteers wearing size medium battle dress uniform (BDU) with recent relevant military experience participated in this study. The volunteers performed shoulder/arm movements (while wearing each armor treatments) and completed the garment impediment perception as well as wearer acceptability scales. The body areas of neck side, shoulder top, and armscye front showed the highest frequency of reported impediments. Resistance to movement and localized pressure were the most frequently mentioned types of impediment. The armor system B had the most areas of impediment, and was rated as more restrictive than the control garment and armor system A for each movement. For wearer acceptability, no significant differences were found between the control garment and armor system A for all eight items; this indicated that subjects did not perceive a difference between wearing the control garment and armor system A. There was a trend for wearer acceptability to decrease from wearing the control garment to armor systems A to C to B.

• The Research Journal of the Costume Culture
• /
• v.31 no.2
• /
• pp.213-227
• /
• 2023

To analyze the status and needs of the small- and medium-sized garment manufacturing industry in Busan, this study comprised an online survey of companies and interviews with 14 representatives of the 98 companies. The results are as follows: Approximately 34.7% of the garment manufacturers were located in Geumjeong-gu, Busan. The most common type of work was the contracting factory type. Daily production output was between 100pcs and 300pcs. Production materials comprised 42.9% woven and 24.8% knitted fabrics. Main products were menswear, uniforms, womenswear, casual wear, sports and leisure wear, protective clothes, and children's clothing. The main clients were uniform companies, main factories, wholesale markets, online shopping malls and promotion companies, exporters, and department stores. As a result of a survey on industrial needs with company representatives, their satisfaction with company employees was 57.2%, and the most important factor when hiring employees was job-related competencies, among which the ability to understand the sewing process was the most necessary. In terms of computer software literacy, illustrations and pattern CAD/CAM are required. They thought industry-university cooperation is crucial for advantage for advantage research and product development, as it allows for the sharing knowledge, resources, and especially human resources. The greatest administrative issue were human resources and funding.

• Fire Science and Engineering
• /
• v.28 no.4
• /
• pp.97-103
• /
• 2014

To ensure adequate protection from the risk of burns, fire fighter's turnout has a composite of more than three components and air gaps between layers of materials. During the flame exposure, radiation and convection heat transfer occurs in the air gap, thus the air gap acts as a thermal resistance with non-linear characteristics. Therefore, in this study, the experiments were performed to identify the effect of various air gap width (0~7 mm) on the thermal protective performance of fire fighter's clothing. The temperatures on each layer and RPP (Radiant Protective Performance, the most effective index representing the thermal protective performance) were measured with various incident radiant heat fluxes. The temperature at the rear surface of the garment decreased and RPP increased with increasing air gap width because the thermal resistance increased. Especially, it could be found that RPP value and air gap width has almost linear relation for the constant incident heat flux conditions. Thus relatively simple RPP predictive equation was suggested for various incident heat flux and air gap conditions.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.25 no.4
• /
• pp.707-718
• /
• 2001

The purpose of this study is to evaluate a newly developed protective suit with the fragments of grenade. The protection efficiency should be strengthened upon the degree of wound. The fragment weight of the used grenade was measured and the kinetic energy of the maximum speed of the fragments in the field test was 137.7J and this could be the protective efficiency test by the multitude fragments in less than 0.031g of the M16A1. The panel inserted to the new demining suit has protection rate of 100% within the distance of 1m and sample II has protection rate of 100% only beyond the distance of 5m. The test showed that the protection rate on the protective suit of the existing garment was comparatively high, however, the protection rate of the sleeve part was very low. The new demining suit through the research demand some complementary measures to lower the temperatures in ear, average skin temperatures, and the temperatures-humidity inside the clothing for summer climate condition, It showed that 30 minutes of rest on the clothing was difficult to go back to the original condition. But in winter climate condition, there was no problem in the temperature, humidity, and comfort to go back to the original condition during the rest and was better in warmth.

• The Research Journal of the Costume Culture
• /
• v.17 no.5
• /
• pp.834-848
• /
• 2009

The purpose of this study is to analyse the research trends and to find a future direction in the area of clothing construction in Korea. The data were included articles on clothing construction published in the five major journals from 2000 through 2008 in Korea. The identified 513 articles were categorized in eight areas: design related clothing construction, study of body types, study of patterns, size of apparel, fitting of clothing, protective clothing and functional clothing, sewing and the others. In the results of examining the percentage of articles on clothing construction among articles published in each journal, the percentage of articles on clothing construction was highest as 21.2% in the Journal of Korean Home Economics and next, 19.3% in the Research Journal of the Costume Culture. As to the percentage of research on clothing construction according to theme, research on protective clothing and functional clothing were largest as 28.2%, and next, research on body types as 18.9%, and research on garment size systems as 10.5%. Research on protective clothing has increased remarkably since 2000, and particularly in 2004 it was so active that it occupied 44.1% of research on clothing construction. Next, with regard to the subjects of research, research with female subjects was more frequent than that with male subjects according to gender, and research with men and women in their twenties was most frequent according to age. These results show somewhat unbalanced tendencies in terms of research subjects.

• Fashion & Textile Research Journal
• /
• v.15 no.3
• /
• pp.444-451
• /
• 2013

This paper surveys the physical properties of aramid and aramid/nylon hybrid air-jet textured yarns(ATY) for protective garments according to wet and dry texturing conditions. Aramid and nylon filaments were used to make two kinds of para-aramid ATY and four kinds of aramid/nylon hybrid ATY with dry and wet treatments. The analyzed physical properties of six specimens (made on the ATY machine) are as follows. The tenacity and initial modulus of aramid and aramid/nylon hybrid ATY decreased with the wetting and breaking strain; however, the yarn linear density of aramid and hybrid ATY increased with wetting treatment. The dry and wet thermal shrinkage of the hybrid ATY increased with wetting. The stability of aramid and hybrid ATY also increased with wetting. The physical properties of core/effect type hybrid ATY showed significantly more change than the core type hybrid ATY and the physical properties of nylon/aramid core/effect hybrid ATY showed significantly more change than the of aramid/nylon core/effect hybrid ATY. A higher bulky and breaking strain of hybrid ATY require ATY processing conditions of nylon on the core part with wetting and aramid on the effect part. ATY processing conditions for nylon and aramid on the core part with wetting are required for a higher tenacity and modulus. ATY processing conditions of nylon and aramid on the core with no wetting are required for a low thermal shrinkage.

• Fashion & Textile Research Journal
• /
• v.15 no.3
• /
• pp.437-443
• /
• 2013

This paper investigates the physical properties of aramid and aramid/nylon hybrid air jet textured filaments for protective garments relative to ATY nozzle diameters. Three types of para-aramids(840d, 1,000d, 1,500d) and nylon(420d) filaments were prepared; in addition, 840d aramid/420d nylon and three kinds of aramid filaments were texturized with a variation of air jet nozzle diameters(0.6, 0.75, 1 and 1.2 mm) on the AIKI air jet texturing machine. The measured physical properties of 16 specimens are as follows. The linear densities of aramid and aramid/nylon hybrid ATY increased with a larger nozzle diameter. The tenacity and initial modulus of aramid and hybrid ATY linearly decreased with a larger nozzle diameter; in addition, the breaking strain increased with the nozzle diameter. The dry and wet thermal shrinkage of hybrid ATY increased with a larger nozzle diameter from 0.6 mm to 1 mm and then decreased at a nozzle diameter of 1.2 mm (which seems to be a critical diameter). The wet and dry thermal shrinkage of aramid/nylon hybrid ATY are influenced by the nylon part of the hybrid yarns because the wet and dry thermal shrinkages of aramid ATY are less than 0.2%. The instabilities of aramid and aramid/nylon hybrid ATY were not influenced by the air jet nozzle diameter; however, they increased with the linear density of ATY.