• Journal of the Semiconductor & Display Technology
• /
• v.16 no.4
• /
• pp.1-4
• /
• 2017

Encapsulation of organic based devices is essential issue due to easy deterioration of organic material by water vapor. Atomic layer deposition (ALD) is a promising solution because of its low temperature deposition and quality of the deposited film. Moisture permeation has a mechanism to pass through defects, Thin Film Encapsulation using inorganic / organic / inorganic hybrid film has been used as promising technology. $Al_2O_3$ / Polymer / $Al_2O_3$ multilayer film has shown excellent environmental protection characteristics despite of thin thicknesses of the films.

• International Journal of Advanced Culture Technology
• /
• v.10 no.4
• /
• pp.555-560
• /
• 2022

In this study, the insertion loss and phase delay according to the multi-layer structure radome parameters were analyzed using the boundary value solution approach, and the multi-layer structure and hexa mesh structures with low-loss electrical characteristics for the Ku-band transmission/reception frequency of 10.7 ~ 14.5 GHz were designed and manufactured. A hexa mesh was applied to minimize radio wave transmission and scattering, which lowered the transmittance refractive index according to the radio incident angle and minimized dielectric loss through high-density foam. Similar to the simulation result, the transmission loss obtained the gain in a specific receiving frequency band, and in the transmission frequency band, an excellent low loss characteristic was obtained with an insertion loss of 0.8dB or less. The results of this study can be used in radio transmission radomes of low-weight, low-cost end-system protection devices.

• Fire Science and Engineering
• /
• v.22 no.3
• /
• pp.188-193
• /
• 2008

Numerical simulation was carried out for a propane fire of mass transfer rate 3g/m^2-s$ on a 1m high vertical wall. The objectives of this study are to confirm the outcomes of evaluation of the simulator through simulation of natural convection, and to compare the results of the wall fire with those of previous studies. It was confirmed that the simulated boundary layer was laminar at C_s=0.2$ while it was turbulent at C_s=0.1$. The z direction velocity showed lack of turbulent mixing as seen in the natural convection case, and the profiles of temperature and velocities were in relatively good agreement with those of experiment and previous simulation. It was found that the air entrainment into the boundary layer was well predicted.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.2
• /
• pp.47-53
• /
• 2000

The fluxless wetting properties of TSM-coated glass substrate were evaluated by the wetting balance method. We could estimate the wettability of the TSM with new parameters obtained from the wetting balance test for one side-coated specimen. It was more effective in wetting to use Cu as a wetting layer and Au as a protection layer than to use Au itself as a wetting layer. The SnSb solder showed better wettability than SnAg, SnBi, and SnIn solders. The contact angle of the one side-coated glass substrate to the Pb-free solders could be calculated from the farce balance equation by measuring the static force and the tilt angle.

• Structural Engineering and Mechanics
• /
• v.50 no.4
• /
• pp.471-486
• /
• 2014

The number of explosive attacks on civilian structures has recently increased. Protection of structure subjected to blast load remains quite sophisticated to predict. The use of the pyramid cover system (PCS) to strengthen sandwich structures against a blast terror has great interests from engineering experts in structural retrofitting. The sandwich steel structure performance under the impact of blast wave effect is highlighted. A 3-D numerical model is proposed to study the PCS layer to strengthen sandwich steel structures using finite element analysis (FEA). Hexagonal core sandwich (XCS) steel panels are used to study structural retrofitting using the PCS layer. Field blast test is conducted. The study presents a comparison between the results obtained by both the field blast test and the FEA to validate the accuracy of the 3-D finite element model. The effects are expressed in terms of displacement-time history of the sandwich steel panels and pressure-time history effect on the sandwich steel panels as the explosive wave propagates. The results obtained by the field blast test have a good agreement with those obtained by the numerical model. The PCS layer improves the sandwich steel panel performance under impact of detonating different TNT explosive charges.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.4
• /
• pp.373-378
• /
• 2006

We report on plasma damage free-sputtering technologies for organic light emitting diodes (OLEDs), organic thin film transistor (OTFT) and flexible displays by using a box cathode sputtering (BCS) method. Specially designed BCS system has two facing targets generating high magnetic fields ideally entering and leaving the targets, perpendicularly. This target geometry allows the formation of high-density plasma between targets and enables us to realize plasma damage free sputtering on organic layer without protection layer against plasma. The OLED with Al cathode prepared by BCS shows electrical and optical characteristics comparable to OLED with thermally evaporated Mg-Ag cathode. It was found that OLED with Al cathode layer prepared by BCS has much lower leakage current density ($1{\times}10^{-5}\;mA/cm^2$ at -6 V) than that $(1{\times}10^{-2}{\sim}-10^0\;mA/cm^2)$ of OLED prepared by conventional DC sputtering system. This indicates that BCS technique is a promising electrode deposition method for substituting conventional thermal evaporation and DC/RF sputtering in fabrication process of organic based optoelectronics.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.12
• /
• pp.6092-6115
• /
• 2017

This paper demonstrates a case for an end-to-end pure Application Security Layer for reliable and confidential communications within an Internet of Things (IoT) constrained environment. To provide a secure key exchange and to setup a secure data connection, Transport Layer Security (TLS) is used, which provides native protection against replay attacks. TLS along with digital signature can be used to achieve non-repudiation within app-to-app communications. This paper studies the use of TLS over the JavaScript Object Notation (JSON) via a The Constrained Application Protocol (CoAP) RESTful service to verify the hypothesis that in this way one can provide end-to-end communication flexibility and potentially retain identity information for repudiation. As a proof of concept, a prototype has been developed to simulate an IoT software client with the capability of hosting a CoAP RESTful service. The prototype studies data requests via a network client establishing a TLS over JSON session using a hosted CoAP RESTful service. To prove reputability and integrity of TLS JSON messages, JSON messages was intercepted and verified against simulated MITM attacks. The experimental results confirm that TLS over JSON works as hypothesised.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.53-54
• /
• 2005

We report on plasma damage free-sputtering technologies for organic light emitting diodes (OLEDs), organic thin rim transistor (OTFT) and flexible displays by using a box cathode sputtering (BCS) method. Specially designed BCS system has two facing targets generating high magnetic fields ideally entering and leaving the targets, perpendicularly. This target geometry allows the formation of high-density plasma between targets and enables us to realize plasma damage free sputtering on organic layer without protection layer against plasma. The OLED with top cathode prepared by BCS shows electrical and optical characteristics comparable to OLED with thermally evaporated Mg-Ag cathode. It was found that TOLED with ITO or IZO top cathode layer prepared by BCS has much lower leakage current density ($1\times10^{-5}$ mA/cm2 at -6V) than that ($1\times10^{-1}\sim10^{\circ}mA/cm^2$)of OLED prepared by conventional DC sputtering system. This indicates that BCS technique is a promising electrode deposition method for substituting conventional thermal evaporation and dc/rf sputtering in fabrication process of organic based optoelectronics.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.1-5
• /
• 2017

Encapsulation of organic based devices is essential issue due to easy deterioration of organic material by water vapor. Thin layer of encapsulation film is required to preserve transparency yet protecting materials in it. Atomic layer deposition(ALD) is a promising solution because of its low temperature deposition and quality of the deposited film. $Al_2O_3$ or $Al_2O_3/TiO_2/Al_2O_3$ multilayer film has shown excellent environmental protection characteristics despite of thin thicknesses of the films. $Al_2O_3/TiO_2/Al_2O_3$ multilayer and 1.5 dyad layer of $Al_2O_3/polymer/Al_2O_3$ deposited by ALD was measured to have water vapor transmittance rate(WVTR) well below the detection limit($5.0{\times}10^{-5}g/m^2day$) of MOCON Aquatran 2 equipment.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3060-3063
• /
• 1999

We made a multi-layer conveyor sterilizing system using UV rays to prolong a storage period of dried marine products. The system is composed of 5 layer conveyor belt of 3 m long each, thus 15 m long in total. It is designed to radiate UV rays for 10 minutes the dried marine products, and can process 300 kg/hour. Eight UV lamps of 30 cm long and 15 W of power with 254 nm wave length are installed in parallel, 15 cm high above in each belt, and 40 lamps in total. The whole system is covered by 1 mm thick metal plates to block the UV rays except a front side which is covered with 5 mm thick plastic plates coated with UV protection film to survey inside of the system. A sterile ratio is about 99.97% with 10 minutes sterilization using this system.