• Journal of the Korean Wood Science and Technology
• /
• 제12권2호
• /
• pp.10-19
• /
• 1984

The $3{\times}3{\times}30$ ($cm^3$) sized lumbers of Populus alba-grandulosa L. were treated with four fire-retardant solutions of ammonium sulfate, monoammonium phosphate, diammonium phosphate and aluminium chloride for 1, 15, 30, and 60 minutes and 1, 3, and 7 days. Thereafter they were air-dried and burned at high temperature about $1,800^{\circ}C$ and for short time of five minutes. This study estimated the relationship between absorbed chemical amounts and rate of weight loss or residual bending strength of these burned lumbers. The results were as follows: 1) In absorption amount of fire-retardant chemicals, diammonium phosphate showed the largest, aluminium chloride the smallest, but monoammonium phosphate and ammonium sulfate showed similar level. 2) The absorption amount of chemicals was decreased with the increase of specific gravity in the same species except aluminium chloride. 3) The rate of weight loss was decreased as the absorption amount of chemicals increased, especially monoammonium phosphate was most effective. 4) The MOR value of the residual bending strength was increased as the absorption amount of chemicals increased and especially monoammonium phosphate showed the most efficient effect. 5) Aluminium chloride showed more striking increase of MOR value of residual bending strength with the increase of absorption amount than any other chemical, therefore its MOR value was similar to the maximum MOR value of the most effective monoammonium phosphate. 6) The correlation between weight loss and MOR value of the residual bending strength was negative and aluminium chloride showed the most striking negative relation, but the others showed similar trends. 7) The correlation between work to proportional limit and absorption amount of chemicals was positive and the degree of increase in work to proportional limit was most in aluminium chloride, and the next, in monoammonium phosphate and diammonium phosphate in turn. 8) The correlation between work to maximum load and absorption amount of chemicals showed positive and diammonium phosphate revealed the best result and aluminium chloride showed better results than other two chemicals.

• Journal of the Korean Wood Science and Technology
• /
• 제33권5호통권133호
• /
• pp.7-12
• /
• 2005

The objective of this study is to estimate the mechanical behavior in bending and the anatomical changes of wood under several deflection rates. Sample specimens of water-saturated Japanese cedar (Cryptomeria japonica) were stressed to rupture under several deflection rates. Mechanical properties of wood such as modulus of elasticity, modulus of rupture and stress at proportional limit, and anatomical changes affected by deflection rates were estimated. Microscopic observations on compression side of the test specimens when the specimen was loaded to rupture were carried out by the SEM (scanning electron microscopy). The results are summarized as follows: 1. The mechanical properties of wood were affected by variations of the deflection rates. The modulus of elasticity (MOE), modulus of rupture (MOR) and stress at proportional limit were in proportion to the logarithm of deflection rates. 2. The deflection of wood at rupture in bending increased as deflection rates decreased. 3. The variations of the microscopic deformations of sample specimens were closely related to the deflection of wood at rupture. In case of largely deflected wood by maximum bending load, severe and abundant microscopic deformations were observed.

• 농업과학연구
• /
• 제48권3호
• /
• pp.597-606
• /
• 2021

Due to the characteristics of the farmland in Korea, forward and reverse shift is the most used. The fatigue of farmers is caused by forward and reverse shifting with a manual transmission. Therefore, it is necessary to improve the convenience of forward and backward shifting. This study was a basic study on the development of a current control system for forward and reverse shifting of agricultural tractors using proportional control valves and a controller. A test bench was fabricated to evaluate the current control accuracy of the control system, and the stability of the controller was evaluated through CPU (central processing unit) load measurements. A controller was selected to evaluate the stability of the proportional valve controller. The stability evaluation was performed by comparing and analyzing the command current of the controller and the actual current measured. The command current was measured using a CAN (controller area network) communication device and DAQ (data acquisition). The actual current was measured with a current probe and an oscilloscope. The control system and stability evaluation was performed by measuring the CPU load on the controller during control operations. The average load factor was 12.27%, and when 5 tasks were applied, it was shown to be 70.65%. This figure was lower than the CPU limit of 74.34%, when 5 tasks were applied and was judged to be a stable system.

• Journal of the Korean Wood Science and Technology
• /
• 제31권2호
• /
• pp.84-91
• /
• 2003

본 연구에서는 3 수종(이태리 포플러, 소나무, 굴참나무재)을 공차별(0, 0.15, 0.3, 0.45 mm)로 초산비닐 수지와 레소시놀-페놀 공축합 수지를 이용하여 접합 제작하였다. 휨시험에서 핑거공차에 따라서 검출되는 AE와 휨강도성능 특성을 살펴본 결과는 다음과 같았다. 레소시놀재의 AE파 발생시기가 초산재보다 빨랐으며, 레소시놀재의 AE파 사상총수는 하중의 증가와 함께 계속적으로 증가하였으며 총발생 사상총수도 초산재보다 휠씬 많이 나타났다. 또한, 레소시놀재의 AE파 사상총수는 낮은 하중에서도 많은 개수가 발생하였다. 비례한도 내에서도 레소시놀 접착제를 사용한 경우에는 많은 AE파가 검출되었다. 따라서 레소시놀 접착제로 접착한 핑거 접합재의 휨시험으로부터 얻은 AE 신호는 핑거공차에 따른 접합재의 강도 예측이나 보증에 이용 가능할 것으로 판단되었다.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.7-12
• /
• 2003

Mixture formation in the cylinder of a lean bum engine has been observed by Laser Induced Fluorescence technique. XeCl laser (308nm) was used to produce a laser sheet. 3-pentanone has been added to iso-octane fuel to produce fluorescence, the intensity of which is proportional to the concentration of the fuel. The laser sheet was introduced through the piston window and the fuel distribution in the vertical plane was observed through a side window. Comparison has been made for the cases of selected fuel injection timing as 0, 360, 405, and 450 CA. For the case of 0 and 360 CA injection, uniform fuel distribution in the combustion chamber has been obtained at the ignition time which is favorable for the high load mode. And the late injection cases, 405 and 450 CA, revealed the stratified formation of rich mixture around the spark plug. That extends the lean misfire limit and reduces cyclic variation in the low load mode.

• 한국공간구조학회논문집
• /
• 제4권3호
• /
• pp.103-109
• /
• 2004

본 논문은 조합하중을 받는 공간구조물의 안정경계를 파악하는 것이다. 구조물에 작용하는 독립된 여러 가지 하중벡터는 기본이 되는 하중 모드와 하중매개 변수를 이용하여 나타내고, 독립된 하중 매개변수에는 비례관계를 설정함으로서 하나의 하중변수에 의해 하중을 부여한다. 구조물의 좌굴하중 즉 임계점은 평형조건이 불안정이 되는 극한점과 분기점으로 분류되고, 가장 낮은 하중이 좌굴하중으로 정의된다. 본 논문에서는 기하학적 비선형 문제를 해석하기 위한 수치해석법으로는 호장법과 뉴턴-랩슨법을 이용하였으며, 본 해석을 통하여 안정경계를 파악함은 물론 좌굴모드 및 좌굴하중을 명확히 규명하였다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 봄 학술발표회논문집
• /
• pp.85-91
• /
• 2000

The smallest value of the load when the equilibrium condition becomes to be unstable is defined as the buckling load. The primary objective of this paper is to analyse stability boundaries for star dome under combined loads and is to investigate the iteration diagram under the independent loading parameter In numerical procedure of the geometrically nonlinear problems, Arc Length Method and Newton-Raphson iteration method is used to find accurate critical point(bifurcation point and limit point). In this paper independent loading vector is combined as proportional value and star dome was used as numerical analysis model to find stability boundary among load parameters and many other models as multi-star dome and arches were studied. Through this study we can find the type of buckling mode and the value of buckling load.

• Journal of the Korean Wood Science and Technology
• /
• 제19권3호
• /
• pp.35-44
• /
• 1991

In this study, thickness 40mm glulams were composed of thickness 5mm, 10mm Quercus laminas and Pinus koraiensis laminas to study on the effect of load variation on transition of neutral axis of laminated veneer lumber(LVL). The transition of neutral axis was examined by strain variation, which was checked by strain gauge. amplifier, recorder, and strain meter. The elasticity of glulam was estimated by E = $\Sigma(E_i\;I_ i)$/I and this estimated elasticity values were compared with the elasticity values of glulam in bending. The result obtained can be summarized as follows: 1. The location of neutral axis of glulam was effected by glulam composition methods 2. The neutral axis did not shift by load variation within proportional limit. 3. The estimated elasticity of glulam by E = $\Sigma(E_i\;I_ i)$/I showed much lower value than the elasticity of glulam in bending.

• Journal of the Korean Wood Science and Technology
• /
• 제13권4호
• /
• pp.67-72
• /
• 1985

To improve the bending strength of sawdustboard, verious resin contents of 10, 13, 16, and 19% were applied to the thin shell (face layer) composed with wire net or not. The shell effect of sawdust and wire net composition formed with core sawdustboard were evaluated. Forcusing on the effects of wire net composition and noncomposition including a comparison with chipboard and veneer complyboard, bending properties (Modulus of rupture (MOR), Modulus of elasticity (MOE), Stress at proportional limit ($S_{pl}$). Work to maximum load ($W_{ml}$))were analyzed and discussed. 1. In modulus of rutpute, veneer comply was the highest (621.5 kg/$cm^2$), and next decreasing order was wire net composition (159.1 kg/$cm^2$), chipboard (81.75 kg/$cm^2$), and wire net noncomposition (76.21 kg/$cm^2$) as in modulus of elasticity, work to maximum load, except for stress at proportional limit. 2. The highly significant effects were shown in both wire net composition and noncomposition, at the same time wire net composition exceeded two times of noncomposition throughout resin contents in bending properties. Chipboard was similar to the mean or 16% resin content in noncomposirion. 3. Every board in wire net composition above 10% resin content was beyond 100 kg/$cm^2$ in MOR, minimum allowable strength for structural use according to KS F 3104. In conclusion, the feasibility for improving the bending strength of weak sawdustboard by wire net composed shell was offered.

• 대한기계학회논문집
• /
• 제13권3호
• /
• pp.472-478
• /
• 1989

본 연구에서는 FRP의 파괴인성평가를 위한 기초적인 자료를 얻기 위하여 FRP 중에서도 널리 사용되고 있는 SMC재를 준비하고 3점 굽힘시험을 실시하여 노치선단에서의 손상거동 및 균열진전저항유선으로부터 안정파괴개시점을 검토하였다.