• Journal of the Society of Disaster Information
• /
• v.20 no.1
• /
• pp.20-31
• /
• 2024

Purpose: Research and development of high-strength concrete enables high-rise buildings and reduces the self-weight of the structure by reducing the cross-section, thereby reducing the thickness of beams and slabs to build more floors. A large effective space can be secured and the amount of reinforcement and concrete used to designate the base surface can be reduced. Method: In terms of field construction and quality, the effect of reducing the occurrence of drying shrinkage can be confirmed by studying the combination of low water bonding ratio and minimizing bleeding on the concrete surface. Result: The ease of site construction was confirmed due to the high self-charging property due to the increased fluidity by using high-performance water reducing agents, and the advantage of shortening the time to remove the formwork by expressing the early strength of concrete was confirmed. These experimental results show that the field application of ultra-high-strength concrete with a design standard strength of 100 MPa or higher can be expanded in high-rise buildings. Through this study, we experimented and evaluated whether ultra-high-strength concrete with a strength of 130 MPa or higher, considering the applicability of high-rise buildings with more than 120 floors in Korea, could be applied in the field. Conclusion: This study found the optimal mixing ratio studied by various methods of indoor basic experiments to confirm the applicability of ultra-high strength, produced 130MPa ultra-high strength concrete at a ready-mixed concrete factory similar to the real size, and tested the applicability of concrete to the fluidity and strength expression and hydration heat.

• Journal of the Microelectronics and Packaging Society
• /
• v.31 no.2
• /
• pp.23-27
• /
• 2024

In this study, the time-dependent warpage behavior caused by the viscoelastic properties of prepreg in a printed circuit board (PCB) was analyzed by finite element method (FEM). The accurate viscoelastic properties of the prepreg were measured by stress relaxation test, which were then incorporated into constructed warpage analysis model. When the PCB was subjected to repeated thermal cycles, the warpage of the PCB was restored to its initial state when only the elastic properties of the prepreg were considered, but when the viscoelastic properties were also considered, the warpage was not restored and permanent warpage change occurred. The warpage analysis for three different types of prepreg was conducted to compare their mechanical reliability, and the results showed that materials with elastic properties dominating over viscoelastic properties experienced less warpage, resulting in better mechanical reliability.

• Food Science and Preservation
• /
• v.31 no.4
• /
• pp.612-622
• /
• 2024

We examined the physicochemical properties and microbial safety of Enoki mushrooms during storage at 5℃ for 9 weeks, with different packaging containers that are corrugated, Al-coated, and without packaging (control). The weight change of Enoki mushrooms in the different containers due to moisture loss was 1.9%, 0.9%, 0.6% for control, corrugated, and Al-coated packaging, respectively. The degree of browning rapidly increased as the storage period increased in the control sample. However, corrugated and Al-coated packaging suppressed the browning degree. The changes of color L-, a-, and b-vlaues were minimal changes in Al-coated packaging. There was no significant difference in the total amino acids, polyphenol oxidase, and peroxidase in corrugated packaging and Al-coated packaging, regardless of the storage period. The microbial growth such as total aerobic bacteria, yeast, and mold of Enoki mushroom during the storage period, were significantly suppressed in Al-coated packaging samples as compared to the control and corrugated packaging. In conclusion, Al-coated packaging has beneficial effects such as preventing moisture loss, maintaining browning degree, inhibiting oxidative enzyme reaction, and ensuring microbial safety of Enoki mushrooms during the storage period. Al-coated packaging is considered effective for extending the shelf-life and improving the storage and distribution of mushrooms.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.39 no.7
• /
• pp.1030-1037
• /
• 2010

A fresh juice has become a new functional food available for dieting and health. However, the shelf-life of vegetable juice is very short because of the absence of heat pasteurization process. To elongate the shelf-life of vegetable juices, such as Angelica keiskei and Brassica loeracea var. acephala, the changes of microbiological, chemical and sensory property by UV irradiation were investigated. The total aerobic bacterial numbers of A. keiskei and B. loeracea var. acephala vegetable juices were $3.2{\times}10^5$ and $7.0{\times}10^4\;CFU/mL$, respectively, after wring process. However, the numbers were $3.6{\times}10^3{\sim}9.7{\times}10^3$ and $3.7{\times}10^3{\sim}2.7{\times}10^4\;CFU/mL$ after UV treatment on wring juice, and this lower microbial number was maintained during storage. The number of coliform bacteria also reduced significantly by UV treatment, and the bactericidal effect was higher when the flow rate is slower. The increase of lightness and yellowness, and decrease of redness were observed after treatment of UV on both vegetable juices, but the differences were not significant between flow rates. The ascorbic acid contents of vegetable juices were reduced by UV irradiation regardless of flow rate, and storage. Overall acceptance in sensory analysis revealed that there was no significant difference between the control and vegetable juice irradiated UV at 0 days, but sample with UV treatment showed higher score at 3 days. Therefore, UV treatment on vegetable juice can elongate the shelf-life without any problems in flavor and color.

• Archives of design research
• /
• v.19 no.1 s.63
• /
• pp.253-262
• /
• 2006

Research of color has been developed and also has raised consumer desire through changing from a tool to pursue curiosity or beauty to a tool creating effects in the 20th century. People have been interested in colors as a dynamic expression of results since the color TV appeared. The meaning of colors has been recently diversified as the roles of colors became important to the emotional aspects of design. While auto colors have developed along with such changes of the times, black led the color trend during the first half of the 20th century from 1900 to 1950, a transitional period of economic growth and world war. Since then, automobile production has increased apace with the rapid economic growth throughout the world and automobiles became the most expensive item out of the goods that people use. Accordingly, increasing production induced facility investment in mass production and a technology leveling was achieved. Auto manufacturing processes are very complicated, auto makers gradually recognized that software changes such as to colors or materials was an easier way for the improvement of brand identity as opposed to hardware changes such as the mechanical or design components of the body. Color planning and development systems were segmented in various aspects. In the segmentation issue, pigment technology and painting methods are important elements that have an influence on body colors and have a higher technical correlation with colors than in other industries. In other words, the advanced mixture of pigments is creating new body colors that have not existed previously. This diversifies the painting structure and methods and so maximizes the transparency and depth of body colors. Thus, body colors that are closely related to technical factors will increase in the future and research on color preferences by region have been systemized to cope with global competition due to the expansion and change of auto export regions.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.12
• /
• pp.1102-1139
• /
• 2002

A review on the papers published in the Korean Journal of Air-Conditioning and Refrigerating Engineering in 2000 and 2001 has been done. Focus has been put on current status of research in the aspect of heating, cooling, ventilation, sanitation and building environment. The conclusions are as follows. (1) Most of fundamental studies on fluid flow were related with heat transportation of facilities. Drop formation and rivulet flow on solid surfaces were interesting topics related with condensation augmentation. Research on micro environment considering flow, heat, humidity was also interesting for comfortable living environment. It can be extended considering biological aspects. Development of fans and blowers of high performance and low noise were continuing topics. Well developed CFD technologies were widely applied for developing facilities and their systems. (2) Most of papers related with heat transfer analysis and heat exchanger shows dealt with convection, evaporation, and channel flow for the design application of heat exchanger. The numerical heat transfer simulation studies have been peformed and reported to show heat transfer characteristics. Experimental as well as numerical studies on heat exchanger were reported, while not many papers are available for the system analysis including heat exchanger. (3) A review of the recent studies on heat pump system shows that performance analysis and control of heat pump have been peformed by various simulations and experiments. The research papers on multi-type heat pump system increased significantly. The studies on heat pipe have been examined experimently for change of working characteristics and strut lure. Research on the phase change has been carried out steadily and operation strategies of encapsulated ice storage tank are reported experimentally in several papers. (4) A review of recent studies on refrigeration/air conditioning system have focused on the system performance and efficiency for new alternative refrigerants. Evaporation and condensation heat transfer characteristics are investigated for tube shapes and new alternative refrigerants. Studies on components of refrigeration/air conditioning system are carried to examine efficiency for various compressors and performance of new expansion devices. In addition to thermophysical properties of refrigerant mixtures, studies on new refrigerants are also carried out, however research works on two-phase flow seemed to be insufficient. (5) A review of the recent studies on absorption cooling system indicates that heat and mass transfer phenomena have been investigated to improve absorber performance. Various experimental data have been presented and several simulation models have been proposed. A review of the recent studies on duct and ventilation shows that ventilation indices have been proposed to quantify the ventilation performance in buildings and tunnels. Main efforts have been focused on the applications of ventilation effectiveness in practice, either numerically using computational fluid dynamics or experimentally using tracer gas techniques. (6) Based on a review of recent studies on indoor thermal environment and building service systems, research issues have mainly focused on many innovative ideas such as underfloor air-conditioning system, personal environmental modules, radiant floor cooling and etc. Also, the new approaches for minimizing energy consumption as well as improving indoor environmental conditions through predictive control of HVAC systems, various activities of building energy management and cost-benefit analysis for economic evaluation were highlighted.

• Applied Biological Chemistry
• /
• v.48 no.2
• /
• pp.132-139
• /
• 2005

The major obstacle in the popularization of Chungkookjang is the short shelf-life of $2{\sim}3$ months and some problems concerning storage including the growth of molds even in the products even within shelf-life. To solve these problems we conducted a research to improve its storage by using the vacuumed packaging and sanitary method through seed culture, innoculation and sterilization. For the optimization of storage time, temperature and sterilization temperature, we measured viable cell numbers of bacteria and fungi, amount of gas outbreak and contents of amino type nitrogen and monitored these experimental results by response surface methodology of SAS program, so that we could observe the quality changes of Chungkookjang during shelf-life. Especially fungi, which are the biggest troublemaker in Chungkookjang shelf-life, couldn't be detected from the generally and vacuum-packed samples; also, viable cell numbers were highly influenced by sterilization temperature and in vacuum-packed samples. In the case of vacuum-packed samples, amount of gas outbreak was highly influenced by sterilization temperature of its storage conditions and it was higher in generally packed samples as compared to vacuum-packed samples even at any storage conditions. The changes of pH in generally and vacuum-packed samples were highly influenced by the storage temperature. As the temperatures of storage and sterilization were higher and the storage time was longer, so the amount of gas outbreak was accordingly lower. These results showed that amino type nitrogen contents in generally and vacuum-packed samples were systematically influenced by the temperature, storage time and sterilization temperature. Also the result showed that the change of amino type nitrogen contents during storage was less in vacuum-packed samples than in general ones. Based on the above results, we can produce Chungkookjang products with extended shelf-life of as far as 6 months without any quality change using sanitary manufacturing method, vacuumed packaging condition, sterilization in $70^{\circ}C$ for 60 minutes and storage under $10^{\circ}C$ during shelf-life. According to this research, we have the possibility to greatly increase the goods value of Chungkookjang by developing the manufacture processing and packaging.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.2
• /
• pp.169-181
• /
• 2007

Statement of problem: Titanium is well known as a proper metal for the dental restorations, because it has an excellent biocompatibility, resistance to corrosion, and mechanical property. However, adhesion between titanium and dental porcelains is related to the diffusion of oxygen to the reaction layers formed on cast-titanium surfaces during porcelain firing and those oxidized layers make the adhesion difficult to be formed. Many studies using mechanical, chemical and physical methods to enhance the titanium-ceramic adhesion have been actively performed. Purpose: This study meant to comparatively analyse the adhesion characteristics depending on different titanium surface coatings after coating the casts and wrought titanium surfaces with Au and TiN. Material and method: In this study, the titanium specimens (CP-Ti, Grade 2, Kobe still Co. Japan) were categorized into cast and wrought titanium. The wrought titanium was cast by using the MgO-based investment(Selevest CB, Selec). The cast and wrought titanium were treated with Au coating($ParaOne^{(R)}$., Gold Ion Sputter, Model PS-1200) and TiN coating(ATEC system, Korea) and the ultra low fusing dental porcelain was fused and fired onto the samples. Biaxial flection test was done on the fired samples and the porcelain was separated. The adhesion characteristics of porcelain and titanium after firing and the specimen surfaces before and after the porcelain fracture test were observed with SEM. The atomic percent of Si on all sample surfaces was comparatively analysed by EDS. In addition, the constituents of specimen surface layers after the porcelain fracture and the formed compound were evaluated by X-ray diffraction diagnosis. Result: The results of this study were obtained as follows : 1. The surface characteristics of cast and wrought titanium after surface treatment(Au, TiN, $Al_2O_3$ sandblasting) were similar and each cast and wrought titanium showed similar bonding characteristics. 2. Before and after the biaxial flection test, the highest atomic weight change of Si component was found in $Al_2O_3$ sandblasted wrought titanium(28.6at.% $\rightarrow$ 8.3at.%). On the other hand, the least change was seen in Au-Pd-In alloy(24.5at.% $\rightarrow$ 9.1at.%). 3. Much amount of Si components was uniformly distributed in Au and TiN coated titanium, but less amount of Si's was unevenly dispersed on Al2O3 sandblasting surfaces. 4. In X-ray diffraction diagnosis after porcelain debonding, we could see $Au_2Ti$ compound and TiN coating layers on Au and TiN coated surfaces and $TiO_2$, typical oxide of titanium, on all titanium surfaces. 5. Debonding of porcelain on cast and wrought titanium surface after the biaxial flection is considered as a result of adhesion deterioration between coating layers and titanium surfaces. We found that there are both adhesive failure and cohesive failure at the same time. Conclusion: These results showed that the titanium-ceramic adhesion could be improved by coating cast and wrought titanium surfaces with Au and TiN when making porcelain fused to metal crowns. In order to use porcelain fused to titanium clinically, it is considered that coating technique to enhance the bonding strength between coating kKlayers and titanium surfaces should be developed first.

• Journal of Intelligence and Information Systems
• /
• v.24 no.3
• /
• pp.89-117
• /
• 2018

The Korean companies are intensifying competition with not only domestic companies but also foreign companies in globalization. In this environment, it is essential activities not only for large companies but also Small and Medium Enterprises (SMEs) to get and develop the core competency. Particularly, SMEs that are inferior to resources of various aspects, such as financial resources etc., can make innovation through effective R&D investment. And then, SMEs can occupy a competency and can be survive at the environment. Conventionally, the method of "self-development" by using only the internal resources of the company has been dominant. Recently, however, R&D method through cooperation, also called "Open Innovation", is emerging. Especially SMEs are relatively short of available internal resources. Therefore, it is necessary to utilize technology and resources through cooperation with external companies(such as joint development or contract development etc.) rather than self-development R&D. In this context, we confirmed the effect of SMEs' factors on sales in Korea. Specifically, the factors that SMEs hold are classified as 'Technical characteristic', 'Company competency', and 'R&D activity' and analyzed how they influence the sales achieved as a result of R&D. The analysis was based on a two-year statistical survey conducted by the Korean government. In addition, we confirmed the influence of the factors on the sales according to the R&D method(Self-Development vs. Open Innovation), and also observed the influence change in 29 industrial categories. The results of the study are summarized as follows: First, regression analysis shows that twelve factors of SMEs have a significant effect on sales. Specifically, 15 factors included in the analysis, 12 factors excluding 3 factors were found to have significant influence. In the technical characteristic, 'imitation period' and 'product life cycle' of the technology were confirmed. In the company competency, 'R&D led person', 'researcher number', 'intellectual property registration status', 'number of R&D attempts', and 'ratio of success to trial' were confirmed. The R&D activity was found to have a significant impact on all included factors. Second, the influence of factors on the R&D method was confirmed, and the change was confirmed in four factors. In addition, these factors were found that have different effects on sales according to the R&D method. Specifically, 'researcher number', 'number of R&D attempts', 'performance compensation system', and 'R&D investment' were found to have significant moderate effects. In other words, the moderating effect of open innovation was confirmed for four factors. Third, on the industrial classification, it is confirmed that different factors have a significant influence on each industrial classification. At this point, it was confirmed that at least one factor, up to nine factors had a significant effect on the sales according to the industrial classification. Furthermore, different moderate effects have been confirmed in the industrial classification and R&D method. In the moderate effect, up to eight significant moderate effects were confirmed according to the industrial classification. In particular, 'R&D investment' and 'performance compensation system' were confirmed to be the most common moderating effect by each 12 times and 11 times in all industrial classification. This study provides the following suggestions: First, it is necessary for SMEs to determine the R&D method in consideration of the characteristics of the technology to be R&D as well as the enterprise competency and the R&D activity. In addition, there is a need to identify and concentrate on the factors that increase sales in R&D decisions, which are mainly affected by the industry classification to which the company belongs. Second, governments that support SMEs' R&D need to provide guidelines that are fit to their situation. It is necessary to differentiate the support for the company considering various factors such as technology and R&D purpose for their effective budget execution. Finally, based on the results of this study, we urge the need to reconsider the effectiveness of existing SME support policies.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.2E
• /
• pp.30-45
• /
• 2001

This study considers the environmental factors affecting propagation loss and sonar performance in the continental regions of the East Coast Sea of Korea. Water mass distributions appear to change dramatically in a few weeks. Simple calculation with the case when the NKCW (North Korean Cold Water) develops shows that the difference in propagation loss may reach in the worst up to 10dB over range 5km. Another factor, an eddy, has typical dimensions of 100-200km in diameter and 150-200m in thickness. Employing a typical eddy and assuming frequency to be 100Hz, its effects on propagation loss appear to make lower the normal formation of convergence zones with which sonars are possible to detect long-range targets. The change of convergence zones may result in 10dB difference in received signals in a given depth. Thermal fronts also appear to be critical restrictions to operating sonars in shallow waters. Assuming frequency to be 200Hz, thermal fronts can make 10dB difference in propagation loss between with and without them over range 20km. An observation made in one site in the East Coast Sea of Korea reveals that internal waves may appear in near-inertial period and their spectra may exist in periods 2-17min. A simulation employing simple internal wave packets gives that they break convergence zones on the bottom, causing the performance degradation of FOM as much as 4dB in frequency 1kHz. An acoustic experiment, using fixed source and receiver at the same site, shows that the received signals fluctuate tremendously with time reaching up to 6.5dB in frequencies 1kHz or less. Ambient noises give negative effects directly on sonar performance. Measurements at some sites in the East Coast Sea of Korea suggest that the noise levels greatly fluctuate with time, for example noon and early morning, mainly due to ship traffics. The average difference in a day may reach 10dB in frequency 200Hz. Another experiment using an array of hydrophones gives that the spectrum levels of ambient noises are highly directional, their difference being as large as 10dB with vertical or horizontal angles. This fact strongly implies that we should obtain in-situ information of noise levels to estimate reasonable sonar performance. As one of non-stationary noise sources, an eel may give serious problems to sonar operation on or under the sea bottoms. Observed eel noises in a pier of water depth 14m appear to have duration time of about 0.4 seconds and frequency ranges of 0.2-2.8kHz. The 'song'of an eel increases ambient noise levels to average 2.16dB in the frequencies concerned, being large enough to degrade detection performance of the sonars on or below sediments. An experiment using hydrophones in water and sediment gives that sensitivity drops of 3-4dB are expected for the hydrophones laid in sediment at frequencies of 0.5-1.5kHz. The SNR difference between in water and in sediment, however, shows large fluctuations rather than stable patterns with the source-receiver ranges.