• Journal of Technologic Dentistry
• /
• v.31 no.4
• /
• pp.9-15
• /
• 2009

The purpose of this study was to observe the change of mechanical property and microstructure in porcelain fused to gold alloy by heat treatment. PFG alloys are composed with Au-Pd-Ag alloy of the additional elements with indium, tin and copper. Specimens were tested in hardness using vicker,s micro-hardness tester and the surface micro structural changes were analysed by SEM and EDS. The results were as fellows: 1. The vickers hardness showed highest in Au-Pd-Ag alloy of the additional element with tin. 2. By hardening-oxiding result, the vicker,s hardness increased in additional element with tin but there was no significant difference in additional elements with indium and copper. 3. The surface oxide layer of Au-Pd-Ag alloy with added indium and tin increased but there was small change in additional element with copper. 4. The elements of indium and tin increased with increasing heat treatment in the surface alloy.

• Korea-Australia Rheology Journal
• /
• v.16 no.4
• /
• pp.175-182
• /
• 2004

Colloidal coating solution was prepared to enhance the hydrophilic property of the film surface. Water and ethanol were used as the dispersion media and (glycidoxypropyl) trimethoxysilane (GPS) as a binder in the colloidal silica coatings. Ethylene diamine was added to the colloidal silica solution as the curing agent. The colloidal silica solution was regarded as a hard-sphere suspension model with low volume fraction of the silica particles. Rheological properties of the silica suspensions modified with GPS have been investigated as a function of pH and concentration. The acidic solution showed high viscosity change by fast hydrolysis reaction and adsorption of the organic binders on the surface of silica particles. However, the hydrolysis was slow at the basic condition and the binders combined with themselves by condensation. The viscosity change was smallest at pH 7. The viscosity increased with the curing time after adding ethylenediamine, and the increase of viscosity at low pH was higher than that at high pH. The hydrophilic properties of the coating film were investigated by the contact angle of water and film surface. The smallest contact angle was shown under the strong acidic condition of pH 2.

• Journal of the Korean Magnetics Society
• /
• v.15 no.3
• /
• pp.198-201
• /
• 2005

We investigated the effects of organic additives on the properties of nickel-copper thin films prepared by electroplating. Compared with thin films fabricated by pure electrolyte only, the films utilizing organic additives show different crystalline orientations. With no alteration of plating conditions simply adding the organic materials changed the composition of copper and nickel. The concentration of nickel could be varied to $65-95\%$ depending on the species and concentration of the additives. The change of material property has contributed to the increase or decrease of the magnetoresistance.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.12
• /
• pp.4987-5014
• /
• 2015

The bilinear pairing, also known as Weil pairing or Tate pairing, is widely used in cryptography and its properties help to construct cryptographic schemes for different applications in which the security of the transmitted data is a major concern. In remote login authentication schemes, there are two major requirements: i) proving the identity of a user and the server for legitimacy without exposing their private keys and ii) freedom for a user to choose and change his password (private key) efficiently. Most of the existing methods based on the bilinear property have some security breaches due to the lack of features and the design issues. In this paper, we develop a new scheme using the bilinear property of an elliptic point and the biometric characteristics. Our method provides many features along with three major goals. a) Checking the correctness of the password before sending the authentication message, which prevents the wastage of communication cost; b) Efficient password change phase in which the user is asked to give a new password after checking the correctness of the current password without involving the server; c) User anonymity - enforcing the suitability of our scheme for applications in which a user does not want to disclose his identity. We use BAN logic to ensure the mutual authentication and session key agreement properties. The paper provides informal security analysis to illustrate that our scheme resists all the security attacks. Furthermore, we use the AVISPA tool for formal security verification of our scheme.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.499-504
• /
• 2006

To improve the quality of coating paper, many areas, such as the manufacturing process of inorganic pigment for the coating, the property change of coating color, the surface design of coating pigment and the productivity of coated paper, were studied. In this study the physical properties and printability of coated paper were compared with the coating pigment to modify the surface of large particle and the coating pigment to mix together the large and small particles. After the coating color was mixed under the same conditions in order that the coating color has the same printability, the printability change caused by the surface modification of coating color was investigated. With the surface SEM of coated paper, the efficiency of the surface modification of coating pigment was investigated. The physical property and printability of coated paper, in addition to the physical properties of coating color, were compared and evaluated. Also, the efficiency of printability was evaluated, changing the mixing condition.

• Journal of the Korean Wood Science and Technology
• /
• v.19 no.4
• /
• pp.52-61
• /
• 1991

In this paper, the difference of the property of absorption and desorption for five species in semi-steady state are studied. The species used are listed in Table 1 and the dimension of specimen was $8\times8{\times}T$(Tangential direction)cm and tested in various conditions. A change of average moisture content with time were measured in each cycles. The results obtained are summarized as follows. When the relative humidity in air was maximum or minimum, the distribution of moisture In wood of all specimens were illustrated by exponential curves of decrease or increased from lace 10 center of wood. From the consideration of coefficient of decrease(C), the amount of moisture change of spruce was larger than the others. The pheonomenon was considered no relation to the specific gravity in air dry, but the wood structures. The velocity of the absorption and desorption for species decreased in the order spruce(Picea sitchensis) neodobam(Fagus crenata), solsong(Tsuga heterophylla), meranti(Shorea sp.) and kaesoo(Cercidiphyllum japoicum). In case of constant temperature and water vapor pressure is changed. the amount of absorbed moisture was larger than that of constant water vapor pressure and temperature vaned. In this fact, it is considered that the property of sorption of wood is strongly influenced by vapor pressure gradient than temperature gradient.

• Proceedings of the KIEE Conference
• /
• 2003.07a
• /
• pp.384-386
• /
• 2003

Striking in change that present our country is much by electricity industry reform and the Korea Electric Power Corporation is deciding power distribution system reliability indices every year but power distribution system for reliability evaluation and establishment of investment program are consisting punily. If consider efficient inflection of resources and hereafter power distribution division that is limited for target achievement of schedule level service evaluation and reliability side in operation of the power distribution system, can expect efficient practical use of the power distribution property if gains in electrical side about these change and most suitable investment way consist because there is necessity of electric power plan establishment of area electric power distribution place of business unit. This paper consider proper reliability level and maximum effect through quantitative analysis to gain electrical gains of the power distribution system in reliability side depending on trend DB(Data Base) of data of electric power system composition appliance in this treatise and apply data administration and reliability rate analysis that serve to decide most suitable investment precedence to supply of electric power property to power distribution system present investment algorithm.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2236-2241
• /
• 2008

The surface heat flux of nuclear fuel rod is the most important factor which can affect safety of reactor and fuel. If fuel rod surface heat flux exceeds the CHF(${\underline{C}}ritical$ ${\underline{H}}eat$ ${\underline{F}}lux$), fuel can be damaged. In case of double cooled annular fuel, which is under developing, contains two coolant channels. Therefore, a generated heat in the fuel pellet can move to inner or outer channel and heat flow direction is decided by both sides heat resistance which varied by dimension and material property change which caused by temperature and irradiation. The new program(called DUO) was developed. For the calculation of surface heat flux, a both sides convection by inner/outer coolant, s gap temperature jump and conduction in the fuel are modeled. Especially, temperature and time dependent fuel dimension and material property change are considered during the iteration. A sample calculation result shows that the DUO program has sufficient performance for annular fuel thermal hydraulics design.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.6
• /
• pp.293-299
• /
• 2004

In this paper, thermal and mechanical properties of electric epoxy with water aging were discussed. We made elastic epoxy specimen adding a ratio of 0〔phr〕20〔phr〕, 35〔phr〕 and 53〔phr〕 with modifier to existing epoxy. We studied mechanical property of elastic resin after absorption in water from 0 to 484 hours. As a result, diffusion factor of elastic epoxy showed 20-21${\times}$10$^{-4}$ $\textrm{mm}^2$/s and general epoxy showed 9.5${\times}$10$^{-4}$ $\textrm{mm}^2$/s. Elastic property increased linearly according to addiction and decreased according to water absorption. Tensile strength was reduced according to addition. It was affected by water absorption of micro-void of elastic epoxy. Hardness inclined to decrease after increasing according to absorbed time. In water-absorption state, it was experimented a change of heat flow by temperature of elastic epoxy and change of thermal expansion coefficient. DSC (Differential Scanning Calorimetry) and TMA (Thermomechanical Analysis) equipments were used to measure Tg. A temperature ringe of DSC was from -0($^{\circ}C$) to 200($^{\circ}C$). One of TMA was from -0($^{\circ}C$) to 350($^{\circ}C$). In addition, we investigated structural analysis of water absorbed specimen using SEM (Scanning Electron Microscope).

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1305-1306
• /
• 2006

A monolayer assembly of anthracene-viologen linked thiol ($AMVC_{8}SH$) was fabricated on a gold electrode by self-assembly method. Structural property of the self-assembled monolayers (SAMs) was carried out by optical and electrochemical method. Firstly, we investigated PL spectrum and UV/visible absorption for the optical properties in solution state. Secondly, we determined the characteristics of charge transfer in different electrolyte solutions by electrochemical quartz crystal microbalance (EQCM). From the data, the PL spectrum and UV/visible absorption were observed and the well-defined shape peaks were nearly equal charges during redox reactions and existed to an excellent linear relationship between the scan rates and existed to currents. The mass change was determined during redox reaction. The mass change behavior of SAMs was not only governed by the mobility of the ion in the viologen but the valence of the ion in the electrolyte solution.