• 한국재료학회지
• /
• 제30권12호
• /
• pp.693-700
• /
• 2020

Direct water quenching technique can be used in hot stamping process to obtain higher cooling rate compared to that of the normal die cooling method. In the direct water quenching process, setting proper water flow rate in consideration of material thickness and the size of the area directly cooled in the component is important to ensure uniform microstructure and mechanical properties. In this study, to derive proper water flow rate conditions that can achieve uniform microstructure and mechanical properties, microstructure and hardness distribution in various water flow rate conditions are measured for 3.2 mm thick boron steel sheet. Hardness distribution is uniform under the flow condition of 1.5 L/min or higher. However, due to the lower cooling rate in that area, the lower flow conditions result in a drastic decrease in hardness in some areas in the hot-stamped part, resulting in low martensite fraction. From these results, it is found that the selection of proper water flow rate is an important factor in hot stamping with direct water quenching process to ensure uniform mechanical properties.

• 대한두개안면성형외과학회지
• /
• 제16권3호
• /
• pp.151-153
• /
• 2015

Closed reduction is the treatment of choice for most nasal bone fractures. In this technique, the nasal bone cannot be directly visualized, proper reduction is confirmed by palpation of the bony contour. This confirmation-via-palpation is in most cases too uncomfortable or painful for patients, and this is the reason why most closed reductions of nasal bone fractures are performed under general anesthesia. Recently, ultrasonography has been adopted as a useful diagnostic method and operative adjunct. In this report, we report the use of ultrasonography as a means to provide palpation-less confirmation of proper reduction, which in turn allows for nasal bone reduction under local anesthesia.

• 산업기술연구
• /
• 제25권B호
• /
• pp.89-97
• /
• 2005

Application of proper orthogonal decomposition (POD) and continuous wavelet transform (CWT) is introduced to study wind speed and building roof pressures of flow separation region. In this study, a detailed analysis of the approach wind flow, wind-induced building pressure and the relation between the two fields was carried out using the POD technique and CWT analysis. The results show potential of the application of POD and CWT in characterization of spatio-temporal and spectral properties of the approach wind and its induced dynamic pressure events. Some of findings resulting from the application of this analysis can be summarized as follows: (1) The POD first principal coordinate of the roof pressure in the separated shear layer is closely correlated with the longitudinal component of oncoming flow. (2) The CWT analysis suggests that the extreme peak pressure in the separated shear layer is due to condensed large-scale eddy motions.

• Journal of Welding and Joining
• /
• 제21권1호
• /
• pp.66-71
• /
• 2003

The release of residual stress by mechanical loading and unloading is often performed in the fabrication of box structure fur steel bridge. The proper degree of loading and unloading is significant at release method of residual stress by mechanical loading because that degree is changed by material and geometric shape of welded structure. Therefore, the simulation model that could exactly analyze the release of residual stress by mechanical loading is to be necessary. In this study, the non-linear behavior of weldments under external loading and unloading, such as the decrease and increase of structure stiffness, was investigated by monitoring of nominal stress and strain. Tensile loading and unloading test and the proper degree of stress relaxation was measured by sectioning technique using strain gauge. Analysis model that is indispensable for the effective application of MSR method was established on the basis of test and measurement result.

• 한국지능정보시스템학회:학술대회논문집
• /
• 한국지능정보시스템학회 2001년도 The Pacific Aisan Confrence On Intelligent Systems 2001
• /
• pp.224-229
• /
• 2001

When a semiconductor package is assembled, various materials such as die attach adhesive, lead frame, EMC (Epoxy Molding Compound), and gold wire are used. For better preconditioning performance, the combination between the packaging materials by studying the compatibility of their properties as well as superior packaging material selection is important. But it is not an easy task to find proper packaging material sets, since a variety of factors like package design, substrate design, substrate size, substrate treatment, die size, die thickness, die passivation, and customer requirements should be considered. This research applies case-based reasoning(CBR) technique to solve this problem, utilizing prior cases that have been experienced. Our particular interests lie in building decision support model to aid the selection of proper die attach adhesive. The preliminary results show that this approach is promising.

• 한국가시화정보학회지
• /
• 제3권2호
• /
• pp.57-62
• /
• 2005

The flow characteristics in a confined slot jet impinging on a flat plate were investigated by using cinematic Particle Image Velocimetry technique. The jet Reynolds number was varied from 250 to 1000 for a fixed jet-to-plate spacing of H/W=5. We found that the vortical structures in the shear layer are developed with increase of Reynolds number and that the jet becomes unsteady by the interaction of vortex pairs between 500 and 750 of Reynolds number. Vortical structures and their temporal evolution are verified by using proper orthogonal decomposition.

• 한국연소학회지
• /
• 제6권2호
• /
• pp.29-35
• /
• 2001

Unsteady numerical study has been conducted on combustion dynamics of a lean-premixed swirl-stabilized gas turbine swirl injector. A three-dimensional computation method utilizing the message passing interface (MPI) parallel architecture, large eddy simulation(LES), and proper orthogonal decomposition (POD) technique was applied. The unsteady turbulent flame dynamics are simulated so that the turbulent flame structure can be characterized in detail. It was observed that some fuel lumps escape from the primary combustion zone, and move downstream and consequently produce hot spots. Those flame dynamics coincides with experimental data. In addition, basis modes of the unsteady turbulent flame are characterized using proper orthogonal decomposition (POD) analysis. The flame structure based on odd basis modes is apparently larger than that of even ones. The flame structure can be extracted from the summation of the basis modes and eigenvectors at any moment.

• Structural Engineering and Mechanics
• /
• 제62권5호
• /
• pp.537-550
• /
• 2017

Structural sizing is a rewarding task due to its non-convex constrained nature in the design space. In order to provide both global exploration and proper search refinement, a hybrid method is developed here based on outstanding features of Evolutionary Computing and Teaching-Learning-Based Optimization. The new method introduces an observer phase for memory exploitation in addition to vector-sum movements in the original teacher and learner phases. Proper integer coding is suited and applied for structural size optimization together with a fly-to-boundary technique and an elitism strategy. Performance of the proposed method is further evaluated treating a number of truss examples compared with teaching-learning-based optimization. The results show enhanced capability of the method in efficient and stable convergence toward the optimum and effective capturing of high quality solutions in discrete structural sizing problems.

• ETRI Journal
• /
• 제35권6호
• /
• pp.1029-1037
• /
• 2013

This paper introduces a novel and fast synthesizing method for 3D motions of quadrupedal animals that uses only a small set of motion capture data. Unlike human motions, animal motions are relatively difficult to capture. Also, it is a challenge to synthesize continuously changing animal motions in real time because animals have various gait types according to their speed. The algorithm proposed herein, however, is able to synthesize continuously varying motions with proper limb configuration by using only one single cyclic animal motion per gait type based on the biologically driven Froude number. During the synthesis process, each gait type is automatically determined by its speed parameter, and the transition motions, which have not been entered as input, are synthesized accordingly by the optimized asynchronous motion blending technique. At the start time, given the user's control input, the motion path and spinal joints for turning are adjusted first and then the motion is stitched at any speed with proper transition motions to synthesize a long stream of motions.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2004년도 가을 학술발표회 논문집
• /
• pp.11-18
• /
• 2004

In this paper, an efficient model reduction scheme is presented for large scale dynamic systems. The method is founded on a modal analysis in which optimal eigenvalue is extracted from time samples of the given system response. The techniques we discuss are based on classical theory such as the Karhunen-Loeve expansion. Only recently has it been applied to structural dynamics problems. It consists in obtaining a set of orthogonal eigenfunctions where the dynamics is to be projected. Practically, one constructs a spatial autocorrelation tensor and then performs its spectral decomposition. The resulting eigenfunctions will provide the required proper orthogonal modes(POMs) or empirical eigenmodes and the correspondent empirical eigenvalues (or proper orthogonal values, POVs) represent the mean energy contained in that projection. The purpose of this paper is to compare the reduced order model using Karhunen-Loeve expansion with the full model analysis. A cantilever beam and a simply supported plate subjected to sinusoidal force demonstrated the validity and efficiency of the reduced order technique by K-L method.