• Korean Journal of Plant Resources
• /
• v.35 no.6
• /
• pp.796-804
• /
• 2022

The demand for Chelidonium majus L. subsp. asiaticum H. Hara is expected to increase due to its pharmacological properties such as antibacterial, antioxidant, and anti-inflammatory effects. However, an effective propagation system for this species has not yet been established. This study was conducted to analyze the seed dormancy and germination characteristics of C. majus L. subsp. asiaticum H. Hara native to Korea and establish a mass propagation system. The dormancy type was primarily classified by analyzing the general information of the collected seeds. The seed dormancy breaking was investigated by comparing the effects of cold stratification (0, 2, 4, 8, 10, or 12 weeks) with warm stratification (S, summer temperature, 25/15℃) and intermediate temperature stratification (A, autumn temperature, 15/10℃) of alternating temperature stratification (S12-A4 or S12-A8 weeks). After dormancy break, 500 mg/L GA₃ and GA₄₊₇ treatment replaced cold stratification and improved seed germination. The results of this study are expected to provide basic data for future seed propagation and mass propagation by analyzing the dormancy and germination characteristics of C. majus L. subsp. asiaticum H. Hara seeds.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.1
• /
• pp.54-60
• /
• 2001

This study is to investigate the mechanical properties and the fatigue crack propagation of fire resistance steel for frame structure as the chemical composition was changed by addition of N, B and rolled end temperature was varied. We used two kinds of specimen, the one is parallel and the other is perpendicular to the rolling directions. As rolled end temperature increased, volume fraction of ferrite and pearlite decreased, but volume fraction of baintie and grain size increased. Micro-hardness decreased as rolled end temperature increased, but tensile and yield strength increased. Volume fraction of ferrite and pearlite decreased by addition of N. But volume fraction of bainite, tensile and yield strength increased. Microstructure was changed to martensite by addition of B, and tensile and yield strength increased. Fatigue life of TL direction specimen was shorter than that of LT direction specimen. There was no significant effect to fatigue crack propagation rate by addition of N and changing rolling condition, but fatigue life was increased by addition of B.

• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.74-75
• /
• 1998

The present study employs weak shock theory and bio-heat transfer function to predict the temperature rise due to nonlinear propagation of high amplitude ultrasound. The theory shows that, for the focused ultrasound which is assumed to have an gaussian beam profile and has the focal intensity of $1000W/cm^2$, the temperature rise of liver tissue exposed for 1 second to the energy lost during nonlinear propagation goes up to about $30^{\circ}C$. This indicate that it is necessary to consider the nonlinear propagation induced heating enhancement when setting exposure condition of high intensity focused ultrasound used for cancer thermotherapy.

• Nuclear Engineering and Technology
• /
• v.55 no.6
• /
• pp.2053-2068
• /
• 2023

Following a loss of coolant accident (LOCA), prestressing concrete containment vessels (PCCVs) may experience high thermal load as well as internal pressure. The high temperature stress would increase the risk of premature damage to the containment, which reduces the safety margin during the increasing internal pressure. However, current investigations cannot clearly address the issues of thermal-pressure coupling effect on damage propagation and thus safety of the containment. Thus, this paper offers three simple and powerful damage parameters to differentiate the severity of damage of the containment. Moreover, despite of the temperature action severely threatening the pressure performance of the containment, the research regarding the improvement of the resistant performance of the containment is quite scarce. Therefore, in this paper, a comprehensive comparison of damage propagation and mechanism between conventional and fiber-reinforced concrete (FRC) containments is performed. The effects of fiber characteristics parameters on damage propagation of structures following the LOCA are also specifically revealed. It is found that the proposed damage indices can properly indicate state of damage in the containment body and the addition of fiber can be used to obviously mitigate the damage propagation in PCCV considering the thermal-pressure coupling.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.198-207
• /
• 1998

To determine the effect of temperature and microstructure on the fatigue crack propagation behavior in Ti-3Al-2.5V alloy, experimental investigations have been carried out with the specimens of different temperatures and different volume fractions of prime $\alpha$-phase. The temperatures employed were room temperature, 20$0^{\circ}C$, 30$0^{\circ}C$ and 40$0^{\circ}C$ under the same frequency of 20Hz. To obtain the different volume fractions of the primary $\alpha$-phase, specimens were solution-treated at $\alpha$+$\beta$ and above the $\beta$ region. From the experimental results, following conclusions were obtained. (1) ΔKth was observed to increase with the less volume fraction of the primary $\alpha$-phase. (2) As the temperature increased. (3) Microstructures having more primary $\alpha$-phase showed higher strength at the high temperatures.

• Journal of the Korean Society of Safety
• /
• v.16 no.1
• /
• pp.18-24
• /
• 2001

The fatigue crack growth behavior of the SA516/70 steel which is used for pressure vessels was examined experimentally at room temperature, $-60^{\circ}C$,$-80^{\circ}C$ and $-100^{\circ}C$ with stress ratio of R=0.05, 0.1 and 0.3. Fatigue crack propagation rate da/dN related with stress intensity factor range ${\Delta}K$ was influenced by stress ratio in stable of fatigue crack growth (Region II) with an increase in ${\Delta}K$. The resistance of fatigue crack growth at low temperature is higher compared with that at room temperature, which is attributed to the extent of plasticity-induced by compressive residual stress according to the cyclic loads. Fractographic examinations reveal that the differences of the fatigue crack growth characteristics between room and low temperatures are mainly explained by the crack closure and the strengthening due to the plasticity induced and roughness induced.

• Journal of the Korean Institute of Gas
• /
• v.14 no.3
• /
• pp.8-13
• /
• 2010

Hydrogen is expected to become a new, clean source of energy for the next generation. Therefore, many studies have investigated the characteristics of the hydrogen flame. However, because the hydrogen flame has high temperature, the flame does not emit visible light, and the flame propagates at a high velocity, investigating its characteristics is difficult. In the present study, in order to simultaneously examine the flame temperature and flame propagation velocity of hydrogen/air mixtures, ultra fine thermocouples with diameters of 12.7, 25.4, and 50.8 ${\mu}m$ are utilized. The results show that it is possible to detect the arrival time of the flame. Due to the temperature compensation with the time constants of thermocouples, it is also possible to estimate the flame temperature.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.11a
• /
• pp.80-87
• /
• 2001

The fatigue crack growth behavior of the SA516/60 steel which is used for pressure vessels was examined experimentally at room temperature $25^{\circ}C, -30^{\circ}C, -60^{\circ}C, -80^{\circ}C, -100^{\circ}C$ and -l2$0^{\circ}C$ with stress ratio of R=0.05, 0.1 and 0.3. Fatigue crack propagation rate da/dN related with stress intensity factor range ΔK was influenced by stress ratio in stable of fatigue crack growth (Region II) with an increase in ΔK. The resistance of fatigue crack growth at low temperature is higher compared with that at room temperature, which is attributed to the extent of plasticity-induced by compressive residual stress according to the cyclic loads. Fractographic examinations reveal that the differences of the fatigue crack growth characteristics between room and low temperatures are mainly explained by the crack closure and the strengthening due to the plasticity induced and roughness induced.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.1
• /
• pp.173-179
• /
• 1997

The high temperature fatigue tests were performed using the specimens taken from Cr-Mo-V steel, widely used as thermal power plant turbine materials for examination fatigue behavior of materials in power plants which have been operated for long periods. The fatigue tests at high temperature were performed at the various temperature and applied stress. The results obtained are summarized as follows : The fatigue crack length increases and the fatigue life decreases with temperature and applied stress according to the same number of stress cycle. The fatigue crack propagation and the fatigue life were much influenced by temperature and applied stress.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.7
• /
• pp.1398-1407
• /
• 1992

The prediction of heat loss during laminar flame propagation was carried out by measurement of gas pressure and visualization of flame propagation in the constant volume combustion chamber. And to validate the prediction, the instantaneous temperature at wall of combustion chamber was also measured. Consequently, it was found that heat loss was increased according to increasing of maximum flame travel distance, but rate of heat loss for heat release during laminar flame propagation was nearly constant. And heat loss depends on heat transfer area which was contacted the wall by burned gas regardless to spark plug location.