• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.30 no.6
• /
• pp.319-325
• /
• 2018

This study conducted an experimental investigation on oscillatory behavior of the hydraulic jump roller. Based on the similarity of the hydraulic jump and tidal bore, the behavior of the front face of hydraulic jump with increasing downstream water depth was studied focusing on profile and fluctuation. In this study, for statistical approach, the ensemble averaging was applied to obtain relevant front profile and compared with the time averaging. The front profile gets mildly sloped and the fluctuation of the starting point of hydraulic jump decreases as the downstream water depth increases.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.150.1-150.1
• /
• 2014

Showerhead is used as a main part in the semiconductor equipment. The face plate flatness should remain constant and the cleaning performance must be gained to keep the uniformity level of etching or deposition in chemical vapor deposition process. High operating temperature or long period of thermal loading could lead the showerhead to be deformed thermally. In some case, the thermal deformation appears very sensitive to showerhead performance. This paper describes the methods for robust design using computational fluid dynamics. To reveal the influence of the post distribution on flow pattern in the showerhead cavity, numerical simulation was performed for several post distributions. The flow structure appears similar to an impinging flow near a centered baffle in showerhead cavity. We took the structure as an index to estimate diffusion path. A robust design to reduce the thermal deformation of showerhead can be achieved using post number increase without ill effect on flow. To prevent the showerhead deformation by heat loading, its face plate thickness was determined additionally using numerical simulation. The face plate has thousands of impinging holes. The design key is to keep pressure drop distribution on the showerhead face plate with the holes. This study reads the methodology to apply to a showerhead hole design. A Hagen-Poiseuille equation gives the pressure drop in a fluid flowing through such hole. The assumptions of the equation are the fluid is viscous-incompressible and the flow is laminar fully developed in a through hole. An equation can be expressed with radius R and length L related to the volume flow rate Q from the Hagen-Poiseuille equation, $Q={\pi}R4{\Delta}p/8{\mu}L$, where ${\mu}$ is the viscosity and ${\Delta}p$ is the pressure drop. In present case, each hole has steps at both the inlet and the outlet, and the fluid appears compressible. So we simplify the equation as $Q=C(R,L){\Delta}p$. A series of performance curves for a through hole with geometric parameters were obtained using two-dimensional numerical simulation. We obtained a relation between the hole diameter and hole length from the test cases to determine hole diameter at fixed hole length. A numerical simulation has been performed as a tool for enhancing showerhead robust design from flow structure. Geometric parameters for the design were post distribution and face plate thickness. The reinforced showerhead has been installed and its effective deposition profile is being shown in factory.

• The korean journal of orthodontics
• /
• v.30 no.3 s.80
• /
• pp.367-375
• /
• 2000

If a mandibular prognathic patient has an extremely unnatural anteroposterior and vertical maxilla or keen esthetical perception for facial profile, orthognathic surgery must be performed along with orthodontic treatment, which alone cannot provide satisfactory results in this case. Esthetical improvement becomes an important factor in the satisfaction level of the patient's treatment result, but an attempt to objectively measure beauty holds many problems. Therefore, in the end, the patient submits the final esthetical evaluation based on his/her subjective viewpoint. Because Korean people have a tendency to prefer the facial appeareance of westerners, they favor an oval shaped face over the traditional round face. This research was conducted in response to the complaints raised by patients who claim that their face had become more round from widening of facial width after the orthognathic surgery for manidibular prognathism than before the surgery. The following results were obtained on the changes in facial appearance and patient satisfaction level by analyzing the skull P-A analysis of total of 14 patients (8 male and 6 female) who underwent orthognathic surgery primarily chief complaint for manidibular prognathism and from their responses on questionnaires. These results are to be used in the research on the pre- and post- operative changes in facial height and width from orthognatic surgery. 1. Three ($21.4\%$) of 14 patients said that their face had widened. 2. The A group showed no change in mandibular width but B group showed a 0.7mm reduction. The facial width increased by 0.45mm and 0.66mm in groups A and B, respectively, after the orthognathic surgery 3. After the surgery the facial length changed by an 0.52mm increase in upper facial height , 1.19mm reduction in lower facial height, and 0.7mm reduction in mandibular height in group A. In group B group, there was a 0.67mm reduction in upper facial height, 3.66mm reduction in lower facial height, and 5mm reduction in mandibular height. 4. In reference to facial width, the facial height showed $1.5\%$ reduction in group A and $3.6\%$ reduction in group B after the surgery. 5. In reference mandibular height-to-facial width ratio, there was a $1.3\%$ reduction in group A, and $4.4\%$ reduction in group B after the surgery. 6. In reference to the mandibular height-to-width ratio, there was a $1.3\%$ reduction in group A and $4.3\%$ reduction in group B after the surgery. 7. Although the change in the facial width due to surgery can be ignored, sufficient explanation should be Provided to the patient before surgery on the fact that the face can appear to be relatively wide because of the reduced facial length as result of the surgery.

• The korean journal of orthodontics
• /
• v.6 no.1
• /
• pp.25-32
• /
• 1976

The present study was performed to establish the cephalometric standards of Hellman dental age II C groups of Korean on the roentgenocephalometry. The subjects consisted of 26 males and 25 females with normal occlusion and acceptable profile. The major conclusions may be listed as follows: 1) The tables of standard deviation from the measurements were made. 2) All linear measurements of skeletal pattern in male were greater than in female with exception of the mandibular body length measurement. 3) The labial inclinations of the upper and lower incisors were greater in female than in male. 4) Vertical growth tendency of the face nab conformed in the late primary dentition as compared with the measurements of the mixed dentition.

• Journal of Korean Vacuum Science & Technology
• /
• v.3 no.2
• /
• pp.101-106
• /
• 1999

The main consideration factor to design a magnetron of the sputtering system for TFT-LCD metallization is high sheet resistance (Rs) uniformity which is provided by the high target erosion and high current efficiency. The present study has developed a rectangular magnetron for TFT-LCD to bve considered full target erosion and high film uniformity. After an aluminum-2 at.% and alloy target was installed in a magnetron source and the film was deposited on the glass of 600${\times}$720 mm, the Rs uniformity of the deposited film was measured as functions of the magnet tilt and magnet scanning configuration. And the target erosion profile was observed with the target voltage. When sputtered at 4mtorr and 10kW, the magnet tilt for the high Rs uniformity of 8.38% was 7mm. The plasma voltage at the dwell home and end for full-face target erosion, when scanned the magnetron was 120% compared to the mean voltage of the other area.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.2
• /
• pp.364-375
• /
• 2002

The purpose of this study is to identify the differences between married women's dissatisfaction towards imported and domestic clothing and to test the role of socioeconomic variables on dissatisfaction. Two-piece formal suit was selected as the item, and country of origin of imported suit was not controlled. Sample selection criteria included married women living in Seoul, Korea, between ages 30-59. The data were analysed using factor analysis, paired t-test, and one-way ANOVA. The results indicate, in the Korean clothing market, both international and Korean marketers should be prudent with their price policies and should implement differentiated marketing strategy based on their target market's demogrophic profile. Higher dissatisfaction towards domestic clothing in terms of most factors, under the rapidly globalizing market environment suggests the Korean marketers will be forced to face full-scale harsh competition from international marketers.

• The korean journal of orthodontics
• /
• v.12 no.2
• /
• pp.127-138
• /
• 1982

The present study was performed to establish the cephalometric norms and to study characteristics of craniofacial skeleton of Korean male and female with normal occlusion. The author studied and analyzed statistically vertical cephalometric measurements of the 52 adult male ranging in age from 18 to 26 years and 43 adult female ranging in age from 16 to 30 years with normal occlusion and acceptable profile. The results were as follows; 1. Cephalometric craniofacial norms and standard deviation chart were abtained about adult Korean male and female with normal occlusion. 2. Vertical dimensions of the craniofacial skeleton were larger in male than in female. 3. Lower face was more divergent in female than in male. 4. In simple correlation coefficients between vertical linear mesurements in male and female, high correlation were shown between ATFH and ALFH, PTFH and PLFH, ALFH and ALDH, PLFH and PLDH.

• The korean journal of orthodontics
• /
• v.28 no.6 s.71
• /
• pp.975-979
• /
• 1998

Our Goal of modified segmental osteotomy on maxilla accompanied by mandibular anterior subapical osteotomy was to get the best results from patients of bi-alveolar or bi-maxillary protrusion. In this study, cephalometric and photo (en face, profile) analysis have been compared to define the soft tissue change after surgery. Lip protrusion was efficiently reduced and nasolabial angle was much obtused. Although nose was a little widened, it was quite acceptable. Blood circulation on osteotomized segment was well maintained. This relatively simple methods could be successfully applied to many patients.

• Structural Monitoring and Maintenance
• /
• v.2 no.4
• /
• pp.339-355
• /
• 2015

Corrosion of prestressed concrete structures is one of the main challenges that engineers face today. In response to this national need, this paper presents the results of a long-term project that aims at developing a structural health monitoring (SHM) technology for the nondestructive evaluation of prestressed structures. In this paper, the use of permanently installed low profile piezoelectric transducers (PZT) is proposed in order to record the acoustic emissions (AE) along the length of the strand. The results of an accelerated corrosion test are presented and k-means clustering is applied via principal component analysis (PCA) of AE features to provide an accurate diagnosis of the strand health. The proposed approach shows good correlation between acoustic emissions features and strand failure. Moreover, a clustering technique for the identification of false alarms is proposed.

• Journal of the Korean Vacuum Society
• /
• v.14 no.4
• /
• pp.245-251
• /
• 2005

A high performance dual rocking magnet sputtering gun has been developed. The rocking magnet sputtering gun introduces full-face erosion by rapidly rocking the magnet in the region where the high plasma density is maintained. The newly developed dual rocking magnet sputtering gun whose target utilization was 77 percent achieved high performance in quality in the view of target utilization and target life-time comparing to the existing magnetron sputtering gun. The PIC-MCC target erosion simulation has been performed simultaneously. Comparing experimental target erosion profiles with simulated target erosion profiles, the simulation could estimate the tendency of the target erosion profiles but could not estimate an exact target erosion profile. If the simulation were improved more precisely, the cost reduction for the development of the multiple rocking magnet sputtering gun would be expected.