• 기술혁신학회지
• /
• 제7권1호
• /
• pp.1-20
• /
• 2004

In this paper, we try to explore the nature of open source software development process. The process involves peculiar characteristics which seem to defy the traditional economic reasoning for technology policy. Based upon the comparative case study of open source software development process with the two innovation processes adopted from literature on economic history, we argue that technology policy should strike the balance between provision of innovation incentives and voluntary disclosure of information.

• 전기학회논문지P
• /
• 제65권2호
• /
• pp.142-150
• /
• 2016

This paper developed new manufacture process technology of slim type flexible flat lighting product used lower power white LED. Flexible flat lighting is applied to letter sign lighting, traffic lighting, interior wall lighting, flat lighting, aquarium back lighting, wreath light etc. Main manufacture process technology were developed drawing software for electronics circuit, inkjet electronic circuit pattern and inkjet white ink coating. For pattern printing it was utilized for piezoelectonic inkjet head printing technology. Also high vacuum pressure laminating technology was waterproofing for LED flat lighting protection. Hence, form process technology we were manufactured for flexible flat lighting product of the power 12 W, input voltage 48 V and plane size $480{\times}480mm$. It acquired a these validity from experiment results.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.363-366
• /
• 2004

KAERI is developing the Advanced Spent Fuel Conditioning Process (ACP) as a pre-disposal treatment process for spent fuel. In this process, the management process must operate in intense radiation fields as well as in a high temperature. Therefore, remote maintenance has played a significant role in this process. Hence suitable remote handling and maintenance technology needs to be developed along with the design of the process concepts. To do this, we developed the digital mockup for the ACP. The digital mockup provides the capability of verifying the remote operability of the process without fabrication of the process equipment. In other words, by applying virtual reality to the remote maintenance operation, a remote operation task can be simulated in the digital mockup. Through utilizing this graphic simulation in this digital mockup, general guidelines can be established for designing equipment intended for remote handling and maintenance. Also, the designer of the equipment that must be remotely maintained should ensure that there is adequate access to the process equipment. The graphic simulator will substantially reduce the cost of the develo363pment of the remote handling and maintenance procedure as well as the process equipment.

• 한국주조공학회지
• /
• 제40권2호
• /
• pp.34-42
• /
• 2020

The effects of the initial balancing pressure, filling pressure and maximum build-up pressure on the casting characteristics of the thick-wall thickness casting during the counter-pressure casting process were investigated. Water model experiment and a computer simulation were carried out to evaluate the characteristics during the filling and solidification stages in counter-pressure casting (CPC); as a reference, the low-pressure casting (LPC) process was used. The average dendrite cell size decreased with an increase in the solidification rate and maximum build-up pressure. A turbulent flow occurred during the filling stage of the LPC process, resulting in the formation of inner gas, while a lamellar flow pattern dominated during the CPC process and was more evident with an increase in the initial balancing pressure, improving the mechanical properties of the castings.

• Archives of Metallurgy and Materials
• /
• 제65권4호
• /
• pp.1255-1259
• /
• 2020

This paper aims to investigate the microstructural evolution and mechanical properties of hot-deformed AlMg4 alloys with Mn, Fe, and Si as the main impurities. For this purpose, solidification behavior and microstructural evolution during hot-rolling and heat-treatment processes are investigated by using theoretical calculations and experimental characterization. The crystallization and morphological transformation of intermetallic Al₃Fe, Al₆Mn, and Mg₂Si phases are revealed and discussed in terms of the variation in chemical composition. Following a homogenization heat-treatment, the effect of heat treatment on the intermetallic compounds is also investigated after hot-rolling. It was revealed that the Mg₂Si phase can be broken into small particles and spherodized more easily than the Al₃Fe intermetallic phase during the hot-rolling process. For the Mn containing alloys, both yield and ultimate tensile strength of the hot-rolled alloys increased from 270 to 296 MPa while elongation decreased from 17 to 13%, which can be attributed to Mn-containing intermetallic as well as dispersoid.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.641-644
• /
• 2008

Traditional LTPS TFT needs additional LDD process to decrease leakage current. However the fabrication process is no suitable for PI substrate. Additional laser multi-irradiation will damage the poly-Si to cause the TFT electrical degrade. Therefore we propose the simplified process to activate the $N^+$ and $N^-$ at the same time.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The 8th Asian Symposium on Precision Forging ASPF
• /
• pp.107-114
• /
• 2003

Although cross rolling process has many advantages in forging a joint shaft, an automotive component of front axle unit, subsequent process is necessary to straighten its bending during forging process. In this paper the bending minimization of the joint shaft was studied to eliminate such an additional process. First of all, a characteristic diagram was used to find out factors affecting the bending of the shaft. Also design of experiments was utilized for estimating the influence of those factors. It was found that the phase angle, which is the difference in starting positions between upper and lower dies, was important to minimize the bending of joint shaft and die cooling is necessary to diminish the distribution of bending.

• 산업경영시스템학회지
• /
• 제15권26호
• /
• pp.77-84
• /
• 1992

This paper constructs Croup Technology process-based learning curve model adjusted to a Group Technology environment which accounts for shared learning that occurs when multiple products utilize some of the same process steps. Through this constructed model, the estimated times and productivity of labor calculated by the Group Technology process-based learning curve model are compared with those generated by employing product-based 1 earning curve model. For sensitivity analysis of the model, the impact of learning rate and the ordered production quantity on the ratio differences between Group Technology process-based learning curve model and product-based learning curve model are examined. These results indicate the critical importance of employing Group Technology process-based learning curve model when a process spans multiple products.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1002-1003
• /
• 2006

This research mainly focuses on the development of sinter brazing technology for improving the process related to belt pulley made by sinter hardening. As the machine process of belt pulley takes up more than half of the total manufacturing hours, we propose changing the process to pulley groove brazed and bonded with pulley disc by applying sinter brazing to belt pulley. With the new process, the belt pulley is expected to reduce manufacturing cost to 70% of the original process by applying the sinter brazing technology; and the belt pulley bound by sinter brazing only loses 10% bonding strength compared with the original process.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2005년도 추계 총회 및 학술발표회
• /
• pp.231-233
• /
• 2005