• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.3
• /
• pp.114-118
• /
• 2011

We report on the growth and characterization of nano and micro scale GaN structures selectively grown on the vertex of hexagonal GaN pyramids. $SiO_2$ near the vertex of hexagonal GaN pyramids was removed by optimized photolithgraphy process and followed by a selective growth of nano and micro scale GaN structures by metal organic vapor phase epitaxy (MOVPE). The pyramidal GaN nano and micro structures which have crystal facets of semi-polar {1-101} facets were formed only on the vertex of GaN pyramids and the size of the selectively grown nano and micro GaN structures was easily controlled by growth time. As a result of TEM measurement, Reduction of threading dislocation density was conformed by transmission electron microscopy (TEM) in the selectively grown nano and micro GaN structures. However, stacking faults were newly developed near the edge of $SiO_2$ film because of the roughness and nonuniformity in thickness of the $SiO_2$ film.

• Asian-Australasian Journal of Animal Sciences
• /
• v.28 no.12
• /
• pp.1713-1720
• /
• 2015

The present work describes experiments undertaken to evaluate the usefulness of selected physicochemical indices of semen, cell membrane integrity and sperm chromatin structure for the assessment of boar semen sensitivity to processes connected with pre-insemination procedures. The experiments were carried out on 30 boars: including 15 regarded as providers of sensitive semen and 15 regarded as providers of semen that is little sensitive to laboratory processing. The selection of boars for both groups was based on sperm morphology analyses, assuming secondary morphological change incidence in spermatozoa as the criterion. Two ejaculates were manually collected from each boar at an interval of 3 to 4 months. The following analyses were carried out for each ejaculate: sperm motility assessment, sperm pH measurement, sperm morphology assessment, sperm chromatin structure evaluation and cell membrane integrity assessment. The analyses were performed three times. Semen storage did not cause an increase in the incidence of secondary morphological changes in the group of boars considered to provide sperm of low sensitivity. On the other hand, with continued storage there was a marked increase in the incidence of spermatozoa with secondary morphological changes in the group of boars regarded as producing more sensitive semen. Ejaculates of group I boars evaluated directly after collection had an approximately 6% smaller share of spermatozoa with undamaged cell membranes than the ejaculates of boars in group II ($p{\leq}0.05$). In the process of time the percentage of spermatozoa with undamaged cell membranes decreased. The sperm of group I boars was characterised with a lower sperm motility than the semen of group II boars. After 1 hour of storing diluted semen, the sperm motility of boars producing highly sensitive semen was already 4% lower ($p{\leq}0.05$), and after 24 hours of storage it was 6.33% lower than that of the boars that produced semen with a low sensitivity. Factors that confirm the accuracy of insemination male selection can include a low rate of sperm motility decrease during the storage of diluted semen, low and contained incidence of secondary morphological changes in spermatozoa during semen storage and a high frequency of spermatozoa with undamaged cell membranes.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.13-20
• /
• 2008

This paper describes the design of low power 12bit Digital-to-Analog Converter(D/A Converter) using Pseudo-Segmentation method which shows the conversion rate of 80MHz and the power supply of 1.8V with 0.18um CMOS n-well 1-poly 6-metal process for advanced wireless communication system. Pseudo-segmentation method used in binary decoder consists of simple parallel buffer is employed for low power because of simpler configuration than that of thermometer decoder. Also, using deglitch circuit and swing reduced drivel reduces a switching noise. The measurement results of the proposed low power 12bit 80MHz CMOS D/A Converter shows SFDR is 66.01dBc at sampling frequency 80MHz, input frequency 1MHz and ENOB is 10.67bit. Integral nonlinearity(INL) / Differential nonlinearity(DNL) have been measured ${\pm}1.6LSB/{\pm}1.2LSB$. Glich energy is measured $49pV{\cdot}s$. Power dissipation is 46.8mW at 80MHz(Maximum sampling frequency) at a 1.8V power supply.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.1-6
• /
• 2008

In this paper, millimeter-wave broadband MHEMT (Metamorphic High Electron Mobility Transistor) cascode amplifiers were designed and fabricated. The $0.1{\mu}m$ InGaAs/InAlAs/GaAs MHEMT was fabricated for cascode amplifiers. The DC characteristics of MHEMT are 670 mA/mm of drain current density, 588 mS/mm of maximum transconductance. The current gain cut-off frequency($f_T$) is 139 GHz and the maximum oscillation frequency($f_{max}$) is 266 GHz. To prevent oscillation of the designed cascode amplifiers, a parallel resistor and capacitor were connected to the drain of common gate device. By using the CPW (Coplanar Waveguide) transmission line, the cascode amplifier was designed and matched for the broadband characteristics. The designed amplifier was fabricated by the MHEMT MMIC process that was developed through this research. As the results of measurement, the amplifier was obtained 3 dB bandwidth of 50.37 GHz between 20.76 to 71.13 GHz. Also, this amplifier represents the S21 gain with the average 7.07 dB gain in bandwidth and the maximum gain of 10.3 dB at 30 GHz.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.128-135
• /
• 2013

This paper presents a high dimming ratio Power-LED driver IC with high power which is capable of controlling LEDs. In order to accomplish a high dimming ratio LED driver, the preloading inductor current methodology is proposed for the power stage of the proposed method to achieve the fast transient response time during the Power-LED load switching. The information containing the current flowing on the LEDs can be utilized to predict the amount of the current on the inductor. The minimum LED current rising time of existing high dimming ratio Power-LED driver is limited by $3{\mu}s$, however that of the proposed high dimming ratio Power-LED driver is reduced about 1/10. The LED driver is implemented with 0.35um 60V BCDMOS 2-poly 4-metal process. The measurement results show that the proposed LED driver system features the minimum rising time as small as 240ns at the dimming frequency of 1KHz with a 12V of input voltage, nine white LEDs and 353mA of LED current. The LED rising time and power conversion efficiency of the chip are measured to be 240ns and 93.72%, respectively.

• The Journal of Engineering Geology
• /
• v.26 no.1
• /
• pp.51-61
• /
• 2016

New building methods are needed to aid increased inner-city redevelopment and industrial construction. A particular area of improvement is the efficient use of cut slopes, with the minimization of associated problems. A retaining wall of precast panels can resist the horizontal earth pressure by increasing the shear strength of the ground and reinforcing it through contact with the panels. Precast panels allow quick construction and avoid the problem of concrete deterioration. Other problems to be solved include the digging of borrow pits, the disposal of material cut from the slope, and degradation of the landscape caused by the exposed concrete retaining wall.This study suggest the methods of improvement of an existing precast panel wall system by changing the appearance of the panels to that of natural rock and improving the process of adhering the panel to a vertical slope. The panels were tested in the laboratory and in the field. The laboratory test verified their specific strength and behavior, and the field test assessed the panels' ground adherence at a vertical cutting. Reinforcement of the cutting slope was also measured and compared with the results of 3D numerical analysis. The results of laboratory test, identified that the shear bar increase the punching resistance of panel. And as a results of test construction, identified the construct ability and field applicability of the panel wall system adhered to in-situ ground. In addition to that, extended measurement and numerical analysis, identified the long-term stability of panel wall system adhered to in-situ ground.

• Journal of Korean Society of Disaster and Security
• /
• v.12 no.3
• /
• pp.59-67
• /
• 2019

In this study, the UAV (Unmammed Aerial Vehicle) was applied for the photogrammetry of the construction site and the safety management of steel pipe scaffold. The research site is a temporary facility for building reinforcement on Samcheok Campus of Kangwon National University. The installation condition of the steel pipe scaffold was investigated, and the pillar distance, the beam distance and the wale distance were surveyed. As a result, it was found that the beam distance of the scaffold in the longitudinal direction was in good agreement with the standard, but the pillar distance and the wale distance were found to be less than the standard. Three-dimensional data can be used in drone shooting to enable three-dimensional measurement, so that it is possible to measure facilities hidden or located inside other facilities. Through the drone shooting, the condition of the site can be quickly recorded and the surveying can be carried out without interfering with the work of the field personnel. Although the installation of the temporary structure must be strictly observed to ensure the safety of the workers, it is found that the installation standards are still neglected in the field. In order to prevent this practice, it was thought that the legal system should be supplemented so that it could be checked periodically by using UAV in the field process management.

• Education of Primary School Mathematics
• /
• v.11 no.2
• /
• pp.121-139
• /
• 2008

This study analyzed problem presenting and solving activities in elementary school mathematics class to enhance insights of teachers in class for providing real meaning of learning. Following research problems were selected to provide basic information for improving to sound student oriented lesson rather than teacher oriented lessons. Protocols were made based on video information of 5th grade elementary school 'Na' level figure and measurement area 3. Congruence of figures, 4. Symmetry of figures, and 6. Areas and weight. Protocols were analyzed with numbering, comment, coding and categorizing processes. This study is an qualitative exploratory research held toward three teachers of 5th grade for problem solving activities analysis in problem presenting method, opportunity to providing method to solve problems and teachers' behavior in problem solving activities. Following conclusions were obtained through this study. First, problem presenting method, opportunity providing method to solve problems and teachers' behavior in problem solving activities were categorized in various types. Second, Effective problem presenting methods for understanding in mathematics problem solving activities are making problem solving method questions or explaining contents of problems. Then the students clearly recognize problems to solve and they can conduct searches and exploratory to solve problems. At this point, the students understood fully what their assignments were and were also able to search for methods to solve the problem. Third, actual opportunity providing method for problem solving is to provide opportunity to present activities results. Then students can experience expressing what they have explored and understood during problem solving activities as well as communications with others. At this point, the students independently completed their assignments, expressed their findings and understandings in the process, and communicated with others. Fourth, in order to direct the teachers' changes in behaviors towards a positive direction, the teacher must be able to firmly establish himself or herself as a teaching figure in order to promote students' independent actions.

• Korean Journal of Food Science and Technology
• /
• v.20 no.6
• /
• pp.820-826
• /
• 1988

The freezing point$(t_f)$, latent heat of freezing$({\triangle}\;H_f)$ and kinetic constant of fleering$(k_f)$ were determined from DSC thermogram at cooling rate $-2.5^{\circ}C/min{\sim}-10.0^{\circ}C/min$. The freezing point of various starches was decreased with an increase in cooling rate, and that of whole starches were lower than defatted starches. Changes of the latent heat of freezing was not observed at above cooling rate $-2.5^{\circ}C/min$. The latent heat of freezing$({\triangle}\;H_f)$ could be deduced as a function of water content(W) as follows: ${\triangle}\;H_f=0.700W-13.048$, (Kcal/kg) $(35%{\leqq}W{\leqq}70%)\;{\triangle}\;H_f=1.569W-73.861,\;(Kcal/kg)\;(W{\geqq}70%$) In the water content range $35{\sim}90$(wt %), the activation energy of various starches in freezing process was determined $126{\sim}270$ Kcal/mol.

• Korean Journal of Soil Science and Fertilizer
• /
• v.16 no.2
• /
• pp.168-178
• /
• 1983

Influence of several dehydration treatments on original structure and water behavior in the process of drying were investigated employing three hawaiian volcanic ash soils and four synthetic minerals. These three soils were developed under different rainfall condition and contained three different amount of amorphous materials in them. Measurement of water losses by oven drying at $105^{\circ}C$, $P_2O_5$ drying, freeze drying, and critical point drying revealed that more water losses were noted by oven drying than by three other drying techniques and the differences of water losses between oven and $P_2O_5$-drying were closely related to amoun: of amorphous materials in them, showing the order of Kaiwiki > Hilo > Kawaihae. This indicates that dehydration of amorphous materials by elevated temperature ($105^{\circ}C$) excluded water beyond that in the adsorbed (hygroscopic) state. The effect of dehydration treatments on initial structure was visualized by scanning electron microscopy. The micrographs showed that oven-and $P_2O_5$-dried samples formed into large mass of sub-angular blocky, dense, and closed crumbs, while the freeze dried and critical point dried samples resulted in less shrinkage, and small, fluffy and open spongy structure. However, critical point drying technique produced bulkier, softer, and greater open structure samples than even freeze drying. Additional Index Words: original structure, synthetic minerals, critical point drying, $P_2O_5$ drying. 1. This is a part of author's Ph.D. dissertation submitted to the University of Hawaii, Honolulu, Hawaii 96822 in 1979. 2. Professor of Agricultural Chemistry, Korea University.