• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.2
• /
• pp.158-165
• /
• 2008

The carbon dioxide properties change sharply near the critical or pseudo-critical point in the heat transfer processes. The reduction in turbulent, convective heat transfer parameters observed in some supercritical data and in experiments with common gases can be due to property variation, acceleration, buoyancy or combinations of these phenomena, depending on the conditions of the applications. In this study, the measurement for the secondary flow driven by buoyancy was carried out on the supercritical carbon dioxide turbulent flows in the different boundary condition with the constant mass flow rate. The available measuring techniques were used to clarify the behaviour of any supercritical fluid. Laser Doppler Velocimeter (LDV) and a special device was used to measure the secondary velocity and turbulent characteristics of the supercritical flows.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.2
• /
• pp.213-217
• /
• 2008

The objective of this research is to investigate the leaching characteristics of unregulated heavy metals such as Ni, Zn, Ba, Be, Sb, Se, V in specified waste. 108 waste samples which were taken from the representative facilities emitting hazardous substances, were analyzed. The rate of leaching of heavy metal was measured using an official test method. From the results, wastewater treatment sludge and dust contained much Ni, and Zn was detected in all samples. Dust and waste catalyst producted from petroleum-refining process tended to reveal V in high concentration. Ba, Be, Sb, Se showed low concentration, but require additional analyses of waste generated at different industries.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.17 no.6
• /
• pp.731-737
• /
• 2007

In this paper, we propose a system for analyzing nutrition status based on hierarchical fuzzy inference approach, where the hierarchical fuzzy approach used to analyze the transition process on the nutritional status from an obesity degree, the previous nutritional status, and the eating pattern with an individual. Moreover we discussed about the selection method of fuzzy membership intervals of the next layer to improve the reliability of inference results in hierarchical fuzzy system, where their intervals are modified by using statistical information of the defuzzified results obtained from the previous layer. To show the effectiveness of this system, we evaluated the nutritional status from the information of anthropometric measurement, biochemical test, and INQ on 113 people over the age of 65, and also analyzed their nutritional status.

• Journal of Information Technology Applications and Management
• /
• v.14 no.1
• /
• pp.1-20
• /
• 2007

IT outsourcing becomes one of the important shills for managing diverse and complex information systems, SIA is considered as an one of the success factors for the successful outsourcing management. Since it helps to establish common goal and provides better visibility of trends and performance, the SLA process must go beyond mere measurement to include a methodology for the ongoing management of service levels, and for the continuous improvement of service activities, functions and processes. Despite SLA is one of the most important skills for the successful outsourcing, few studies have been conducted for academic as well as practical purpose. For this reason, The objective of this study is to develop an SLA's maturity model and empirically demonstrate how SLA's maturity level affects its Performance through SLA's maturity model. The major contributions of this study are in two areas. This study contributes to academicians as well as practitioners. First, from the academic perspectives this study tries investigating the maturity level of the SLA based on empirical data. Second, practitioners can self-test their firms' maturity level using the proposed model. The results of this study show that the SLA's maturity level affected positively SLA's performance. It is founded that the SLA's maturity level had a significant impact on SLA's performance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.10
• /
• pp.1467-1474
• /
• 2004

In this study, a new damage identification method for beam-like structures with a fatigue crack is proposed. which does not require comparative measurement on an intact structure but require several measurements at different level of excitation forces on the cracked structure. The idea comes from the fact that dynamic behavior of a structure with a fatigue crack changes with the level of the excitation force. The 2$^{nd}$ spatial derivatives of frequency response functions along the longitudinal direction of a beam are used as the sensitive indicator of crack existence. Then, weighting function is employed in the averaging process in frequency domain to account for the modal participation of the differences between the dynamic behavior of a beam with a fatigue crack at the low excitation and one at the high excitation. Subsequently, a damage index is defined such that the location and level of the crack may be identified. It is shown from the analysis of vibration measurements in this study that comparison of frequency response characteristics of a beam with a single fatigue crack at different level of excitation forces enables an effective detection of the crack.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.86-89
• /
• 2002

We give pressure stimulation into organic thin films and then manufacture a device under the accumulation condition that the state surface pressure is 10[mN/m]. In processing of a device manufacture, we can see the process is good from the change of a surface pressure for organic thin films and transfer ratio of area per molecule. The structure of manufactured device is Au/Poly-${\gamma}$ Benzyl $_D$-Glutamate/Al and Au/Poly-${\gamma}$ Benzyl $_D$-Glutamate/Au; the number of accumulated layers is 1, 3, 5 and 7. Also, we then examined of the MIM device by means of I-V. The I-V characteristic of the device is measured from 0 to +2[V]. We determined electrochemical measurement by using cyclic voltammetry with a three-electrode system. LB film accumulated by monolayer on an ITO. In the cyclicvoltammetry, An Ag/AgCl reference electrode, a platinum wire counter electrode and LB film-coated ITO working electrode measured in $LiBF_4$ solution, stable up to 0.9V vs. Ag/AgCl.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.201-202
• /
• 2009

ZnO:Al transparent conductive films for solar cells were deposited on the glass substrates at room temperature by facing target sputtering (FTS) method. The sputtering targets were 100 mm diameter disks of 2w.t..%. AZO and Zn metal. ZnO:Al thin films were deposited as a function film thickness. A base pressure was $2{\times}10^{-6}$torr, and a working pressure was 1mTorr. The properties of thin films on the structural, electrical and optical properties of the deposited films were investigated using a four-point probe (Chang-min), an X-ray diffraction (Rigaku), a Hall Effect measurement (Ecopia), an UV/VIS spectrometer (HP) and a $\alpha$-step (Tencor). The lowest resistivity of film was $5.67{\times}10^{-4}[{\Omega}-cm]$ at 500nm. The average transmittance of over 80% was seen in the visible range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.7
• /
• pp.611-617
• /
• 2006

We report the preparation of N doped, p-type ZnO films by post-annealing in $NH_3$ ambient. The properties were examined by XRD, Hall-effect measurement, PL, and SIMS. ZnO films showed better crystallinity and electron concentration of $10^{15}-10^{17}/cm^3$ with post-annealing in $NH_3$ ambient. These films were converted to p-type ZnO by activation thermal annealing process at $800^{\circ}C$ under $N_2$ ambient. The electrical properties of the p-type ZnO showed a hole concentration of $1.06\times10^{16}/cm^3$, a mobility of $15.8cm^2/V{\cdot}s$, and a resistivity of $40.18\Omega{\cdot}cm$. The N doped ZnO films showed a strong photoluminescence peak at 3.306 eV at 13 K, which is closely related to neutral acceptor bound excitons of the p-type ZnO:N. In the SIMS spectra, the incorporation of nitrogen was confirmed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.05a
• /
• pp.73-76
• /
• 1995

In this study, the slab waveguide was fabricated using potassium-nitride(KNO$_3$) or silver-nitride (AgNO$_3$) molten sources by ion-exchange process. The effective refractive indices of waveguide were measured by Prism-Coupling method. and The characteristics of waveguide(mode dispersion, effective diffusion depth. surface refractive index, diffusion coefficient, and refractive index profile etc,) were investigated by WKB method, In the case of potassium ion-exchange, the computer calculation showed that the refractive index profile of waveguide followed Gaussian function, the surface refractive index increased with ion-exchange time and the effective diffusion depth increased a little as ion-exchange time increased, while the surface refractive index of silver ion-exchanged waveguide decreased with ion-exchange time because of the ion depletion on the surface of waveguide, and the effective diffusion depth seriously with ion-exchange tim. Double ion-exchanged waveguide was fabricated by performing silver ion-exchange after potassium ion-exchange. Double ion-exchanged waveguide had a tight mode binding force since the surface refractive index was larger than single step ion-exchanged waveguide.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.198-204
• /
• 2001

The shot peening is largely used for a surface treatment of metallic components where small spherical pellets called shots are blasted onto the surface with velocities up to 100 m/s. This treatment leads to improvement of fatigue behavior due to the developed compressive residual stresses, and so it has gained widespread acceptance I the automobile and aerospace industries. The residual stress profile on surface layer depends on the parameters of shot peening, which are, shot velocity, shot diameter, coverage, impact angle, material properties etc. and the method to confirm this profile is the measurement by X-ray diffractometer only. Despite the importance to automobile ad aerospace industries, little attention has been devoted to the accurate modelling of the process. In this paper, the simulation technique is applied to predict the magnitude ad distribution of the residual stress and plastic deformation caused by shot peening with the help of the finite element analysis.