• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.372-377
• /
• 2005

EMC(Electromagnetic Compatibility) is the ability of an electronic device that operates properly in its intended electromagnetic environment and not be a source of pollution to that environment. The designer anticipates EMC problems at beginning of the process and finds remaining problems in early prototype stages, and tests the final prototypes for EMC as thoroughly as possible. This is a more cost-effective method. In this paper, it analyzes EMC problems that were appeared in actual measurement of electric power control device and presents reduction technique of these problems.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.10
• /
• pp.1895-1902
• /
• 2011

This work was carried out for the measurement of vibration and rotation temperature using the optical emission spectroscopy of nitrogen second positive system in the small plasma torch. Among emissions $N_2$ SP systems, the emission of $N_2$ SP(0-0) was so strong. Emission peaks of SP system increased until the position of 12.5[mm] from the end of plasma torch, after that it decreased. However, vibration temperature decreased from 1540[K] to 1000[K] at the position of 12.5[mm]. In addition, rotational temperature was about 400[K] at the position of 10[mm] and it increased a little as much of 420[K] at 12.5[mm]. Consequently, the plasma torch discussed in this work is possible to apply in the surface treatment process under the low temperature.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.05a
• /
• pp.153-158
• /
• 2000

Flow visualization and PIV measurements were conducted to investigate the flow characteristics of multi-channel with inclination angle. The water flow seeded with tiny vegetable powder as tracers revealed details of flow field. The PIV measurement to acquire multi-point velocity data simulatneously was carried out at three space of plates for 5, 10, and 15mm with variation of inlet flow rates of $0.25m^3/h$ and <$0.5m^3/h.$ Experiment results show that space of plates acts a significant role in separating process.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.6
• /
• pp.743-749
• /
• 1985

In this study the usefulness of Gas Chromatograph for the measurement of engine exhaust gas composition was confirmed. It was found that the composition of standard gas which was used for the calibration of Gas Chromatograph should not be greatly different from that of exhaust gas. Although self-evident, it cannot be overemphasized that utmost attention should be paid to prevent even a minute amount of air being mixed into the gas throughout the sampling process.

• International Journal of Aeronautical and Space Sciences
• /
• v.3 no.2
• /
• pp.88-94
• /
• 2002

This paper describes attitude determination algorithm for the low earth orbit(LEO) spacecraft using stellar inertial sensors. The cascaded gyro/star tracker extended Kalman filter is constructed to fuse two sensor data. And then the smoothing of the measurement are proposed for an unreasonable jump of star tracker. The smoothing algorithm for the rejection of star tracker error jumps is designed by scalar adaptive filter. The proposed algorithms operate to process the measurement of gyro/star tracker Kalman filter, therefore, it is comparatively simple to apply these methods to other integration systems. Simulations to gyro/star tracker integrated system show that the proposed method is effective.

• Journal of Korea Technology Innovation Society
• /
• v.3 no.1
• /
• pp.139-153
• /
• 2000

The aim of this paper is to provide a new model to evaluate the quantitative value of technology(nonfinancial benefits). This new model is based on the technology stock(technology level) ac-quired in R&D process. The model can explain the quantitative relation between the technology stock(level) and the market value of technology as considering the R&D expenditure to acquire technologies above a certain level(>70%) in comparison with the advanced country and the cost to prevent the technology obsolescence. The value of non-destructive testing technology which is one of the electric power technology is measured quantitatively as a case study.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.307-315
• /
• 1993

A direct draft measurement system was developed based on the swingle tree- the rear component of the single-animal harnessing (or yoking) system . The prototype was made from a tube, on which four strain gages were attached. The pull of the draft animal through the flexible pull chains or ropes causes the beam to bend, The bending strain is sensed by the strain gages and the bridge converts this to a voltage signal. Counterweights keep the tube correctly oriented if the angle of pull changes , while end bearing follow the variations in the angle of pull. Hence, the voltage output is proportional to the draft. the device has highly linear response, acceptable sensitivity negligible error and hysteresis. It is suitable for electronic data acquisition, non-intrusive , easy to attach and detach and is reasonably priced.

• Journal of Korea Technology Innovation Society
• /
• v.2 no.2
• /
• pp.201-218
• /
• 1999

The article contains an introduction of possibility of applying Multi-Attribute Utility Theory(MAUT) for priority setting of R&D projects. MAUT is compared with AHP, which is widely used recently. These two techuiques are applied to set priorities of R&D projects In a Government-funded Research Institute. Six criteria are chosen from consultation with decision makers. They are composed of 1) validity as representative projects, 2) possibility of resource mobilization, 3) spillover effect of developed technologies, 4) possibility of success, 5) scope of participation and 6) clarity of research goal. To set priorities of R&D projects, SMART(Simple MultiAttribute Rating Technique) and DVM(Difference Value Measurement) out of many MAUT methods are used to design the utility function and to determine the weights among criteria. The aggregation model is additive on the assumption the criteria are independent. AHP executes pairwise comparisons for criteria and alternatives. From the results of the case study, the results and theoretical characteristics are compared.

• Journal of Information Technology Services
• /
• v.4 no.1
• /
• pp.41-55
• /
• 2005

In this research, we've studied to the software productivity and quality measures and metrics for raise UP the advanced software industry. For the purpose, we've studied relative research and reorganized 74 metrics. Reorganized 74 metrics were developed considering scalability, measurement and acquisition possibility and verified by software development experts. Finally, we've conducted a survey on the high measurement possibility metrics. Data were gathered from 20 software development project. It was found from the result need more efforts for the software development productivity improvement for advanced software industry.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.25 no.3
• /
• pp.56-65
• /
• 1997

This research was conducted to suggest some directions for desirable urban green space planning through 1) establishing a new classification system by examining the existing concept, problems and characteristics of green space and 2) defining the essence of green space environment and finding some analytical and evaluative methods through a clear establishment of functions, indicators of green space. In the research, measurements of the amount of green space was accompanied with measurements of green covered space, green volume, and the structure of greenery within the frame of vision. As result, three-dimensional measurement was possible, three-dimensional measurement was possible, which turned out to be more effective than the existing 2-dimensional measuring method. It is found that the ratio of green covered space is to proportional to the ratio of green volume in this study. Therefore in green space planning process it is desirable to consider the ratio of green volume all together.