• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.223-228
• /
• 2007

In this paper, Wideband antenna using E-shaped stacked patches has been designed and fabricated for 4th generation mobile communication(IMT-Advanced) AccessPoint application. E-shaped patch was miniature and brodband by made the movement route of current long. And inductive of coaxial probe compensates capacitive by slot. Therefore we fabricated to improve the bandwidth of proposed antenna. The E-shaped single patch antenna has an impedance bandwidth of about 13%(510[MHz]), By adding a second patch at the top of the first patch a bandwidth of 56%(2060[MHz]). The final fabricated antenna could have a good return loss(Return loss ${\leq}-10dB$) and a high gain(over 9.6dBi) at the range of 3.23 ${\sim}$ 5.29 [GHz].

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.5
• /
• pp.87-92
• /
• 2003

In rocket systems, somtimes special devices or equipments are installed near the nozzle exit area where high temperature and pressure combustion gas flows. To pretect these subsystems from severe thermal environment, it is necessary to have accurate thermal data measured from the experimental liquid rocket firing test. Test variables were combustion pressure (200, 300, 400 psi) and mixture ratio (1.5, 2.0, 2.5) and quartz was used as a heat probe. Measurement technique used in this research can be also applied to measure the radiative heat flux inside the combustion chamber which is important imput data for the liquid rocket regenerative cooling system design.

• Journal of Biomedical Engineering Research
• /
• v.30 no.6
• /
• pp.503-509
• /
• 2009

The development of technology has led to ubiquitous health care service, which enables many patients to receive medical services anytime and anywhere. For the ubiquitous health care environment, real-time measurement of biomedical signals is very important, and the medical instruments must be small and portable or wearable. So, such devices have been developed to measure biomedical signals. In this study, we develop the biomedical monitoring device which is sensing the PPG signal, one of the useful signal in the field of ubiquitous healthcare. We design a watch-like biomedical signal monitoring system without a finger probe to prevent the user's inconvenience. This system obtains the PPG from the radial artery using a sensor in the wrist band. But, new device developed in this paper is easy to get the motion artifacts. So, we proposed new algorithm removing the motion artifacts from the PPG signal. The method detects motion artifacts by changing the degree of brightness of the light source. If the brightness of the light source is reduced, the PPG pulses will disappear. When the PPG pulses have disappeared completely, the remaining signal is not the signal that results from the changing blood flow. We believe that this signal is the motion artifact and call it the noise reference signal. The motion artifacts are removed by subtracting the noise reference signal from the input signal. We apply this algorithm to the system, so we can stabilize the biomedical monitoring system we designed.

• Archives of Plastic Surgery
• /
• v.47 no.4
• /
• pp.365-370
• /
• 2020

The ability to directly harvest thin and superthin perforator flaps without jeopardizing their vascularity depends on knowledge of the microsurgical vascular anatomy of each perforator within the subcutaneous tissue up to the dermis. In this paper, we report our experience with ultrahigh-frequency ultrasound (UHF-US) in the preoperative planning of thin and superthin flaps. Between May 2017 and September 2018, perforators of seven patients were preoperatively evaluated by both ultrasound (using an 18-MHz linear probe) and UHF-US (using 48- and 70-MHz linear probes). Thin flaps (two cases) and superthin flaps (five cases) were elevated for the reconstruction of head and neck oncologic defects and lower limb traumatic defects. The mean flap size was 6.5×15 cm (range, 5×8 to 7.5×23 cm). No complications occurred, and all flaps survived completely. In all cases, we found 100% agreement between the preoperative UHF-US results and the intraoperative findings. The final reconstructive outcomes were considered satisfactory by both the surgeon and the patients. In conclusion, UHF-US was found to be very useful in the preoperative planning of thin and superthin free flaps, as it allows precise anticipation of very superficial microvascular anatomy. UHF-US may represent the next frontier in thin, superthin, and pure skin perforator flap design.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.35 no.1
• /
• pp.67-75
• /
• 1993

This study is to analyze both root growth and soil moisture extraction pattern during the growing period of upland crops with respect to soybean, redpepper, sesame. Field and lysimeter tests were conducted under 12 treatments of soil moisture level by the San Cristobal experimental design(1981) and 3 soil type(sand, sandy loam, silty loam) for 4 years('87-'90) at the experimental plot of Rural Development Administration located in Suwon. The results of this study are summarized as follows : 1.For soybean, redpepper and sesame, root growth in dry soil was better than that in wet soil and it could be expressed as a sin function in terms of time. Maximum root depth was about 55cm, 44cm, 40cm respectively. 2.The average soil moisture extraction pattern for soybean, redpepper and sesame were 61.4%, 62.8%, 79.5% for zone l(0-l5cm). 25.5%, 27.1%, 18.3%, for zone 2(15-30cm).11.4%, 9.8%, 2.3% for zone 3(30-45cm), 1.7%, 0.3%, 0.04% for zone 4(45-60cm) respectively. This means that Zone 1 would be the dominant zone in irrigation scheduling. 3.With respect to soybean, the soil moisture extraction pattern(SMEP) was varied somewhat according to the erent maintenance of soil moisture level. The average SMEP for high maintenance of soil moisture was 46%, 29%, 17%, 8%, for middle maintenance of soil moisture was 43%, 29%, 17%, 11 % and for low maintenance of soil moisture was 40%, 28%, 20%, 12%, respectively. 4.With respect to soybean, the soil moisture in the upper layer was distinctly consumed more than that in the lower layer for clay loam soil and the soil moisture of all layers was consumed evenly for sand soil. The SMEP for sandy loam soil showed a middle result compared with the above 2 soil types.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.436-436
• /
• 2011

Recently, spintronic devices with submicron structures are widely investigated to take advantage of their unique micromagnetic properties. In this work, we study the temperature dependence of exchange bias in bilayer anti-dot arrays made by depositing Co (40 nm)/Ni (5 nm) ferromagnetic bilayer on Si substrate to form anti-dot arrays with a diameter $1{\mu}m$. The anti-dot patterning was done only for the upper Co layer, while the Ni underlayer was kept unperforated. The temperature dependences of magnetoresistance (MR) and exchange bias were studied along magnetic easy and hard axes. The in-plane MR measurements were performed using a physical-property measurement system (PPMS ; Quantum Design Inc.) at various temperatures. The standard in-line four-point probe configuration was used for the electrical contacts. As temperature was varied, the MR data were obtained in which in-plane field (H=3 kOe) was applied in the directions along the hard and the easy axes with respect to the lattice plane. The temperature dependences of magnetic anisotropy and exchange bias were also studied along the magnetic easy and hard axes. As temperature decreases, the single peak splits into two peaks. While no exchange bias was observed along the magnetic easy axis, the exchange bias field steadily increased with decreasing temperature along the magnetic hard axis. These results were interpreted in connection with the magnetic anisotropy and the effect of the anti-dots in pinning domain wall motion along the respective direction.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.257-264
• /
• 2007

In this paper, we have designed and fabricated a wide-band and high gain antenna which can integrate a standard of IEEE 802.1la$(5.15\sim5.25\;GHz,\;5.25\sim5.35\;GHz,\;5.725\sim5.825\;GHz)$. We inserted a parallel dual slot into a rectangular patch to have wide-band, and we offset an element of capacitance from the slot by using coaxial probe feeding method. We also designed a converter of $\lambda_g/4$ impedance with taper type line so that wide-band impedance can be matched easily. We finally designed structure with $2\times2$ array in order to improve the antenna gain, and the final fabricated antenna could have a good return loss(Return loss$\leq$-10 dB) and a high gain(over 13 dBi) at the range of $5.01\sim5.95\;GHz(B/W\doteqdot940\;MHz)$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03a
• /
• pp.11-11
• /
• 2010

In order to design for nano structured materials with enhanced thermoelectric properties, the alloys in the pseudo-binary $Bi_2Te_3$-PbTe system were investigated for their micro structure and thermal properties. For this synthesis the liquid alloys were cooled by water quenching method. The micro structure images were taken by using electron probe micro analyzer (EPMA). Dendritic and lamellar structures were clearly observed with the variation in the composition ratio between $Bi_2Te_3$ and PbTe. It was confirmed that a metastable compounds is $PbBi_2Te_4$ in the The $Bi_2Te_3$-PbTe system. The change in the composition increasing $Bi_2Te_3$ ratio causes to change structure from dendritic to lamellar. Seebeck coefficient of alloys 5 which the mixture rate of $Bi_2Te_3$ is 83% was measured as the highest value. In contrast, the others decreased by increasing $Bi_2Te_3$. n-type characteristics was observed at all condition except alloy 6 which $Bi_2Te_3$ ration is 91%. The power factors of all samples were calculated with Seebeck coefficient and resistivity. Also the thermal conductivity was measured by using laser flash analyzer (LFA). In this work, the microstructures and thermal properties have been measured as a function of ratio of $Bi_2Te_3$ in the $Bi_2Te_3$-PbTe system.

• Nuclear Engineering and Technology
• /
• v.45 no.7
• /
• pp.847-858
• /
• 2013

Since 2001, a series of five irradiation test campaigns for atomized U-Mo dispersion fuel rods, KOMO-1, -2, -3, -4, and -5, has been conducted at HANARO (Korea) in order to develop high performance low enriched uranium dispersion fuel for research reactors. The KOMO irradiation tests provided valuable information on the irradiation behavior of U-Mo fuel that results from the distinct fuel design and irradiation conditions of the rod fuel for HANARO. Full size U-Mo dispersion fuel rods of 4-5 $g-U/cm^3$ were irradiated at a maximum linear power of approximately 105 kW/m up to 85% of the initial U-235 depletion burnup without breakaway swelling or fuel cladding failure. Electron probe microanalyses of the irradiated samples showed localized distribution of the silicon that was added in the matrix during fuel fabrication and confirmed its beneficial effect on interaction layer growth during irradiation. The modifications of U-Mo fuel particles by the addition of a ternary alloying element (Ti or Zr), additional protective coatings (silicide or nitride), and the use of larger fuel particles resulted in significantly reduced interaction layers between fuel particles and Al.

• Journal of the Institute of Convergence Signal Processing
• /
• v.16 no.4
• /
• pp.156-161
• /
• 2015

In this paper, a dual-polarized multi-band multi-layer antenna for a vehicle, which operates in the GPS, bluetooth, and DSRC bands, was implemented. The antenna was designed as a multi-layer structure, and a FR4-epoxy substrate with =4.4 and =1.6mm was used. GPS and DSRC antennas have circular polarized characteristics, and a single probe feeding method was applied. Simulated results by Ansys HFSS v11 was compared with the measured ones. The size of the optimally designed antenna is $67mm{\times}67mm{\times}4.8mm$, -10dB bandwidth of the anatenna was measured to be 820MHz, 127MHz, and 862MHz in each band, and 3dB AR bandwidth of the antenna was simulated to be 19MHz and 110MHz in GPS and DSRC bands. The results confirmed that suggested system satisfies the system requirements.