• Current Optics and Photonics
• /
• v.3 no.3
• /
• pp.243-247
• /
• 2019

We have developed a compact, wavelength-selectable, Q-switched Nd:YAG laser at mid ultraviolet for chemical warfare agent detection. The fundamental wave at 1064 nm is delivered by a pulsed solid state laser incorporating with a square-type Nd:YAG rod in a resonator closed by two crossed Porro prisms for environmental reliability. The output energy at 213 nm ($5{\omega}$) and 266 nm ($4{\omega}$) by ${\chi}^{(2)}$ process in the sequentially disposed BBO crystals are measured to be 6.8 mJ and 15.1 mJ, respectively. The output wavelength is selected for $5{\omega}$ and $4{\omega}$ by a motorized wavelength switch. The energy ratio of the $5{\omega}$ to the $4{\omega}$ is varied from 0.05 to 0.85 by controlling the phase matching temperature of the nonlinear crystal for sum-frequency generation without change of the output pulse parameters.

• Computers and Concrete
• /
• v.30 no.1
• /
• pp.9-17
• /
• 2022

This paper discusses the effect of high temperatures (T_s) on the compressive strength and stress-strain curve of recycled fine aggregate concrete (RFAC), based on the experimental results. A total of 90 prisms (100 mm×100 mm×300 mm) were tested. The results show that the compressive strength and elastic modulus of RFAC specimens decreased significantly with increasing T values. As T increased, the strain corresponding to peak stress decreased first when T<200℃ and then increased afterwards. With increasing T values, the stress-strain curves became flat gradually, the peak stress dropped gradually, and ε_p decreased when T<200℃ and increased in the T range of 400-800℃. A stress-strain relations for RFAC exposed to high T_s is proposed, which agree quite well with the test results and may be used to practical applications.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_1
• /
• pp.1001-1010
• /
• 2023

To solve the problem that photovoltaic panels can not harvest electrical energy at a cloudy day and night, a floating solar thermoelectric generator (FSTEG, hereafter) is studied. The FSTEG is consisted of a dome shaped Fresnel lens to condense solar energy, a thermoelectric module connected with a heat sink to keep temperature difference, a floating system simulating a wavy ocean and an electrical circuit for energy storage. The dome shaped Fresnel lens was designed to have 29 prisms and its optical performance was evaluated outdoors under natural sunlight. Four thermoelectric modules were electrically connected and its performance was evaluated. The generated energy w as stored in a Li-ion battery by using a DC-DC step-up converter. For the application of ocean environment, the FSTEG was covered by the dome shaped Fresnel lens and sealed to float in a water-filled reservoir. The harvested energy shows a potential and a method that the FSTEG is suitable for the energy generation in the ocean environment.

• Current Optics and Photonics
• /
• v.8 no.1
• /
• pp.56-64
• /
• 2024

In response to the current situation where general methods cannot effectively compensate for the phase delay of ordinary optical mixers, a multi-layer spatial beam-splitting optical mixer is designed using total reflection triangular prisms and polarization beam splittings. The phase delay is generated by the wave plate, and the mixer can use the existing parallel plates in the structure to individually compensate for the phase of the four output beams. A mixer model is established based on the structure, and the influence of the position and orientation of the optical components on the phase delay is analyzed. The feasibility of the phase compensation method is simulated and analyzed. The results show that the mixer can effectively compensate for the four outputs of the optical mixer over a wide range. The mixer has a compact structure, good performance, and significant advantages in phase error control, production, and tuning, making it suitable for free-space coherent optical communication systems.

• Journal of Korean Ophthalmic Optics Society
• /
• v.19 no.4
• /
• pp.527-532
• /
• 2014

Purpose: The matching of the optical center and the pupil center was measured by photographs in wearing glasses. In this study, the influences of the induced prism by the mismatching are studied. Methods: 74 subjects (148 eyes) who were spectacles wearer were participated in this study. The mean age was $29.19{\pm}12.22$ years (range 19-55 years). The facial photographs of subjects were taken while wearing spectacles. The matching of the corneal reflected image and optical center of the spectacle lens in the horizontal deviations, and the vertical deviations were measured by the observation of the photo image. The prisms induced in accordance with various frame type were calculated from the mismatching deviations. Results: The binocular horizontal deviations were $1.55{\pm}1.70mm$ for the metal frame, $1.71{\pm}2.21mm$ for the clings type plastic frame, and $1.15{\pm}1.38mm$ for the plastic frame. In the horizontal direction induced prism, the ratio over the tolerance was 23%. The ratio were the 17.6% at the BI prism, and 5.4% at the BO prism. The binocular vertical deviation comparisons were $3.93{\pm}1.91mm$ for the metal frame, $5.79{\pm}1.93mm$ for the clings type plastic frame, and 1$6.01{\pm}2.94mm$ for the plastic frame. In the vertical direction induced prism, the ratio over the tolerance was 44.6%. Based on the refraction power, the ratio were 12.2% at -0.25${\leq}-3.00$, and 32.4% at -3.00${\leq}-12.00D$. Conclusions: The induced prisms in the horizontal direction were much in the BI prism. The binocular vertical deviations of the glasses.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.7
• /
• pp.435-443
• /
• 2017

The Characteristics of the flowfields of a square prism having a small square prism were investigated by measuring of lift and drag on the square prism and visualizing the flowfield using PIV. The experimental parameters were the width ratios(H/B=0.2~0.6) of small square prisms to the prism width and the gap ratios (G/B=0~3) between the prism and the small square prism. The drag reduction rate of the square prism initially increased and then decreased with the G/B ratio for the same H/B ratio, and increased with the H/B ratio for the same G/B ratio. The maximum drag reduction rate of 98.0% was observed at H/B=0.6 and G/B=1.0. The lift reduction rate of the square prism was not affected by the width and gap ratios; the total average value was approximately 66.5%. In case of a square prism having a small square prism, the stagnation regions were represented in the upstream and downstream sides of the square prism.

• Journal of the Korea Computer Graphics Society
• /
• v.15 no.4
• /
• pp.1-11
• /
• 2009

In this paper, we present a prism-based mesh culling method to improve effectiveness of continuous collision detection which is a major bottleneck in a simulation using polygonal mesh models. A prism is defined based on two matching triangles between a sequence of times m a polygonal model. In order to detect potential colliding set(PCS) of prism between two polygonal models in a unit time, we apply the visibility test based on the occlusion query to two sets of prisms which are defined from two polygonal models in a unit time. Moreover, we execute the narrow band culling based on SAT(Separating Axis Test) to define potential colliding prism pairs from PCS of prisms extracted as a result of the visibility test. In the SAT, we examine one axis to be perpendicular to a plane which divides a 3D space into two half spaces to include each prism. In the experiments, we applied the proposed culling method to pairs of polygonal models with the different size and compared the number of potential colliding prism pairs with the number of all possible prism pairs of two polygonal models. We also compared effectiveness and performance of the visibility test-based method with those of the SAT-based method as the second narrow band culling. In an experiment using two models to consist of 2916 and 2731 polygons, respectively, we got potential colliding prism pairs with 99 % of culling rate.

• Korean Journal of Optics and Photonics
• /
• v.33 no.6
• /
• pp.295-302
• /
• 2022

In this paper, a wedge prism application method was studied to design a full-high-definition (FHD)-class high-resolution flexible endoscope. In the case of the conventional flexible endoscope optical system, the F number is made large or a liquid lens is applied to obtain the same imaging performance in a wide depth of field. However, there is a problem in that the diameter of the optical system increases because an additional light guide and equipment are required. To solve this problem, two wedge prisms were applied to the flexible endoscope optical system to adjust the image distance for each object distance. First, two wedge prisms were symmetrically placed on the designed endoscopic optical system. An image distance satisfying the target imaging performance according to each objective distance was derived. Next, the wedge prism decenter value for controlling the image distance was derived. By combining these two data, a wedge prism decenter value that satisfied the target imaging performance at each object distance was applied in multi configurations. As a result of the optimal design applied with the wedge prism, a target imaging performance of more than 20% of the modulation transfer function for a resolution of 178 cycles/mm was satisfied in the entire depth of field of 100 mm-7 mm.

• Computers and Concrete
• /
• v.21 no.3
• /
• pp.321-333
• /
• 2018

Flat-slabs, being a significant structural component, not only reduce the dead load of the structure but also reduce the amount of concrete required for construction. Moreover the use of recycled aggregates lowers the impact of large scale construction to nearby ecosystems. Recycled aggregate based concrete being a quasi-brittle material shows enormous cracking during failure. Crack growth in flat-slabs is mostly in sliding mode (Mode II). Therefore sufficient sections need to be provided for resistance against such failure modes. The main objective of the paper is to numerically determine the ultimate load carrying capacity of two self-similar flat-slab specimens and validate the results experimentally for the natural aggregate as well as recycled aggregate based concrete. Punching shear experiments are carried out on circular flat-slab specimen on a rigid circular knife-edge support built out of both normal (NAC) and recycled aggregate concrete (RAC, with full replacement). Uniaxial compression and bending tests have been conducted on cubes, cylinders and prisms using both types of concrete (NAC and RAC) for its material characterization and use in the numerical scheme. The numerical simulations have been conducted in ABAQUS (a known finite element software package). Eight noded solid elements have been used to model the flat slab and material properties have been considered from experimental tests. The inbuilt Concrete Damaged Plasticity model of ABAQUS has been used to monitor crack propagation in the specimen during numerical simulations.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.8
• /
• pp.677-684
• /
• 2007

In the Present Study, a 3-D viscous flow solver, based on unstructured hybrid meshses containing tetrahedra, prisms and pyramids, has been developed. A finite-volume discretization scheme is used for solving the compressible Navier-Stokes equations. A cell-vertex median dual volume is used for spatial discretization. The one-equation Spalart-Allmaras turbulence model has been adopted to evaluate the eddy viscosity. Validation were made by computing laminar and turbulent flows around a 3-D wing for steady flows and turbulent flows around an oscillating 3-D wing in harmonic motion for unsteady flows.