• Journal of the Korean Society of Safety
• /
• v.13 no.2
• /
• pp.22-29
• /
• 1998

The natural convection cooling of simulated electronic chips located on a printed circuit board(PCB) has been studied by Computer Aided Engineering(CAE). In CAE, 3-dimensional finite element model of simulated electronic chip was made to accomplish heat transfer analysis at each design stage of a printed circuit boards for thermal optimization. The simulated electronic chips are installed protrudent from the plate about 3mm. The materials the plates are epoxy and aluminum. The results show that the chip with relatively high heat generation rates should not be close to each other. It is found, as well that cooling effect for the aluminum plate is superior to the epoxy plate and location of maximum temperature is significantly influenced by the structure variation of PCB. In developing PCB and electronic chips, it's recommended that CAE is very useful to estimate to the distribution of temperature.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.321-325
• /
• 2007

Recently, demands on thin multi-layer printed circuit boards(PCB) have been rapidly increased with broad spread of personal portable digital appliances such as multi-media. In case of mobile phone, however, the fact that PCBs have low flexural strength might cause defects. The purpose of this study is to improve the flexural strength by substituting the well-known GFRP(glass fiber reinforced plastic) for CFRP(carbon fiber reinforced plastic). Firstly, finite element simulation was carried out using ABAQUS to find out a unique CFRP layer that has a role to sustain the applied forces mainly in PCB. Secondly, three point bending tests were conducted with the newly designed CFRP PCB model to verify the improvement of the flexural strength. Consequently, it is shown that PCB layered with the CFRP on both outer sides of the board can be used to improve the flexural strength effectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.8
• /
• pp.26-40
• /
• 2000

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.193-197
• /
• 2001

This study was carried out to recover gold, silver and other valuable metals from the printed circuit boards (PCB) of waste computers. PCB samples were crushed to under 1mm by a shredder and initially separated into 30% conducting and 70% non-conducting materials by an electrostatic separator. The conducting materials, which contained the valuable metals, were then used as the feed material for magnetic separation where it was found that 42% was magnetic and 58% non- magnetic. The non-magnetic materials contained 0.227mg/g Au and 0.697mg/g Ag. Further leaching of the non-magnetic component using 2.0M sulfuric acid and 0.2M hydrogen peroxide at 85$^{\circ}C$ extracted more than 95% copper, iron, zinc, nickel and aluminium. Au and Ag were not extracted in this solution, however, more than 95% of Au and 100% of Ag were selectively leached with a mixed solvent (0.2M ammonium thiosulfate, 0.02M copper sulfate, 0.4M ammonium hydroxide). Finally, the residues were reacted with a NaCl solution to leach out Pb while sulfuric acid was used to leach out Sn. Recoveries reached 95% and 98% in solution, respectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.8
• /
• pp.76-85
• /
• 2003

In this paper, a technical method for removing the solder from PCBs has been proposed to simplify the pulverizing process and to get higher quality of materials for recycling of the electronic parts in the Printed Circuit Boards (PCBs). There are several techniques to remove the solder from PCB, such as physical and chemical method, vibration, suction and blowing and so on. Among them, the suction technique turned out the best method by investigation. In the suction method, there are three variables for removing the solder. They are a temperature of the thermal wire, a velocity of moving PCB and a gap between PCB and thermal wire. To find the optimal variables for the system, an experiment has been conducted by a trial and error method. The optimal variables were found $220^{\circ}C$ of temperature, 11.58mm/s of velocity, 10mm of gap (A gap between suction hole and bottom of PCBs is 5mm). The result of the experiment shows that 50% of the solder were removed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.78-81
• /
• 2002

Printed Circuit Boards for satellite are composed of multi-layered copper plate and glass epoxy. Each copper layer have the complicated and different pattern to operate correctly for its mission. Especially. copper layer give effect on the PCB stiffness seriously. But It can make more complicate to predict the exact stiffness of PCB. In KOMPSAT-2 program, too many type of PCB are used for each electronic unit, and they have different type of pattern of copper layer. Solar array regulator has two type of PCB and it will be considered for this study. In this study. we calculate the PCB board stiffness of KOMPSAT-2 SAR unit considering the concept of simplified representative volume element. It will be correlated with the test results under KOMPSAT-2 vibration environmental condition to increase the reliability of this study.

• Proceedings of the IEEK Conference
• /
• 2003.07e
• /
• pp.2375-2378
• /
• 2003

In manufacture of printed circuit boards, one important issue is precisely to measure the three-dimensional shape of the solder paste silk-screened prior to direct surface mounting of chips. This paper presents the 3D shape reconstruction of solder paste using the optical triangulation method based on structured light or slit beam and the measurement algorithm for height, volume. area, and coplanarity on component pads from the 3D range image. Futhermore, statistical process control function is incorporated for process capability analysis.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1272-1278
• /
• 2009

The cancellation method of P/G(power/ground) plane resonances which are generated between the power plane and the ground plane in a 4-layer PCB(Printed Circuit Boards) with a via-hole for the improvement of the RE(Radiated Emission) characteristic is presented. The validity of the proposed method was confirmed from simulation and measurement of performances of signal transmission characteristic, intensities of edge-radiation and radiated emission of PCB with a via-hole.

• IE interfaces
• /
• v.13 no.2
• /
• pp.195-203
• /
• 2000

This paper considers the problem of sequencing printed circuit boards(PCBs) on an automatic surface mount device(SMD) placement machine in order to minimize total setup time. Since the total set of component feeders needed by all boards cannot be loaded simultaneously on the magazine, the setup must be made between two successive boards in the sequence. It is assumed that the setup time depends on the number of component feeders to be replaced in the magazine. An important characteristic is that each feeder occupies a different number of slots in the magazine. This problem is equivalent to travelling salesman problem(TSP) except that the distances between two cities, that is, the setup times between two boards, are not known in advance. So, TSP-based heuristics with new distance functions are presented and their performances are compared through various test problems. Computational results indicate that our heuristics outperform existing methods.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1992.10a
• /
• pp.141-146
• /
• 1992

본 연구에서는 먼저 낙하 충격을 받는 전자 제품을 수학적인 모델링을 행하 므로서 낙하 충격시 제품이 받게되는 충격력을 정량화하였고, 전자 제품내 많은 부품들의 낙하충격에 대한 동특성해석의 일환으로 핵심 부품인 PCB(printed circuit board)를 해석하였다. PCB 해석을 위하여 유한요소법을 사용하였고, PCB에 작용하는 half-sine pulse의 속도 변화에 다른 가속도 응 답 및 최대 충격가속도, 주기의 변화에 다른 PCB의 가속도 응답을 해석하였 다. 제시된 해석 기법은 낙하충격에 대비한 적절한 electric component의 layout및 최적의 PCB 취부조건등의 결정을 가능케 함으로써, 설계단계에서 낙하 충격을 고려한 PCB설계가 될 수 있도록 그 활용 방안을 제시하였고 반복된 낙하충격 실험을 줄일 수 있으므로 경비 절감 및 개발 소요기간도 절감할 수 있다.