• 한국주조공학회지
• /
• 제22권5호
• /
• pp.257-264
• /
• 2002

Effects of Ca content on the refinement of primary Si of Aluminum B390 alloy have been examined. Ca was found to have an effect on the refinement of primary Si particle. Primary Si particle size has been refined as Ca content of the melts decreased and cooling rate increased. A control of Ca content by the addition of $CuCl_2$ to the melt was the most efficient in the refinement of primary Si particles. The minimum size of primary Si particles in this study was $15.0\;{\mu}m$ when a residual content of Ca element in the alloy was 5ppm, Primary Si particle size was refined as primary Si crystallization temperature increased, which was attributed to the decrease of Ca content in the melts.

• 한국주조공학회지
• /
• 제18권6호
• /
• pp.541-549
• /
• 1998

Microstructural characteristics of hypereutectic Al-Si alloys during reheating at semi-solid temperature have been investigated. The size and morphology of primary Si particles in wedge-type mold-cast ingot has been compared with hot-rolled sheet and Si particulate reinforced Al composite. Effects of P and Sr addition on the morphological changes of primary Si particles have been also investigated. Observation of the solidification microstructures of the wedge-type mold-cast ingot at different cooling rates showed that alloying elements such as P and Sr affect the morphology of Si particles, especially in the area solidified at a slow cooling rate. Negligible change in the size of primary crystals was observed after reheating experiment, but ${\alpha}-halo$ formed around the Si particles and fine particles of Si precipitated in the surrounding area of the Si particles. In addition, there seemed to be no coarsening with increasing of holding time and the region of ${\alpha}-halo$ being decreased. Nucleation and recrystallization was accelerated with addition of alloying elements during hot rolling resulting in a decrease of primary Si particle size. In the case of extruded specimens, morphological change of primary Si particles was not observed after reheating. No ${\alpha}-halo$ formation was observed in Si reinforced Al composite because of the oxide film formed on the Si particles which acted as a diffusion barrier between substrate and the primary Si particles.

• 소성∙가공
• /
• 제13권7호
• /
• pp.608-613
• /
• 2004

Mechanical properties of hypereutectic Al-Si alloy are influenced by the size and distribution of primary Si. To investigate the effects of P addition and holding time, hypereutectic Al-Si alloys with various amount of P content were produced in the lab. Then, the size and distribution of primary Si were examined respectively. Mechanical properties of hardness, tensile strength and wear resistance were analyzed in conjunction with the microstructural variations in alloys.

• 열처리공학회지
• /
• 제18권3호
• /
• pp.157-163
• /
• 2005

Effects of refinement of primary Si and residual stress on the mechanical properties of Aluminum B.390 alloy have been examined. Calcium was found to have an effect on the size of primary silicon particles. Primary silicon particle was refined as Ca content decreased. Refinement of primary Si particles led to an improvement in mechanical properties of the alloy; increase of elongation was prominent, above all. By the increase of compressive residual stress in the matrix alloy, tensile strength increased but elongation decreased.

• 한국주조공학회지
• /
• 제24권2호
• /
• pp.85-93
• /
• 2004

Mechanical property of hypereutectic Al-Si alloy is changed according to size and distribution of primary Si. Consequently, the study on the refinement for primary Si is progressed for a long time. But such effect of refinement comes out fading phenomena with the lapse of time. Therefore, this study investigated the optimum condition of primary Si refinement for hypereutectic Al-Si alloy. And we observed various primary Si size with P's fading phenomena. The experiment results were as follows. For experiment of primary Si refinement, we made hypereutectic Al-Si alloy with various amounts of P addition. As a result of experiment, we obtained the fine microstructure at 0.01wt.%P. And the optimum condition of P addition, for preventing from growth of primary Si by P fading, is estimated 0.1wt.%P.

• 열처리공학회지
• /
• 제19권1호
• /
• pp.20-29
• /
• 2006

Wear behaviour of B.390 aluminum alloy with different particle sizes of primary Si against a SM45C counterface was studied as a function of wear load and sliding velocity, using pin-on-disk apparatus under dry condition. The wear rate of specimen with fine primary Si particles showed increased wear resistance at high wear load, on the other side wear resistance of coarse primary Si particle size was improved at low wear load. As the compressive residual stress in the matrix increased remarkably by liquid nitrogen(LN) treatment, wear resistance of the LN treated specimen was more excellent than that of T6 treated specimen.

• 한국재료학회지
• /
• 제30권2호
• /
• pp.51-56
• /
• 2020

In this study, three kinds of metal chills such as SS400, AC4CH and brass, with different thicknesses of 40 ~ 80 mm, were applied for low pressure casting of Al-Si alloy to control cooling rate. The microstructural characteristics with increasing cooling rate were represented using factors including D₁, D₂, size of primary α phases and shape factor and size of eutectic Si. The tensile properties were investigated and additionally analyzed based on the microstructural characteristics. As the cooling rate increased, D₁, D₂, and sizes of primary α phases and eutectic Si apparently decreased and the shape factor of eutectic Si increased to over 0.8. The ultimate tensile strength (UTS) and yield strength (YS) increased with decreasing D₁, D₂, and size of primary α phases, while elongation increased with decreasing size of eutectic Si and concurrently increasing shape factor of eutectic Si. This indicated that the primary α phases and eutectic Si in Al-Si alloy were refined with increasing cooling rate, resulting in improvement of UTS and YS without sacrificing elongation. After the tensile test, preferential deformation of primary α phases was observed in the Al-Si alloy produced at higher cooling rates of more than 0.1 K/s.

• 한국주조공학회지
• /
• 제17권6호
• /
• pp.585-591
• /
• 1997

Hyper-eutectic Al-17.5wt%Si alloy bars of 25 mm in diameter were produced by horizontal continuous casting process. Effect of both casting speed and primary Si refiner (AlCuP) on microstructure and mechanical properties of the alloy have been investigated. With increasing a weight fraction of AlCuP, the average primary Si size decreased down to $20 {\mu}m$. On the contrary, there was no notable changes of microstructure and primary Si size according to the casting speed in the experimental range of this study, indicating that the cooling rate should be increased to optimize and refine microstructure and primary Si size. The experimental results including hardness, tensile strength and wear resistance tests of the processed alloy bars showed a good possibility to develop the high performance wear resistant Al-Si alloy.

• 소성∙가공
• /
• 제14권4호
• /
• pp.319-326
• /
• 2005

In this study, the nano-deformation behavior of semi-solid Al-Si alloy was investigated using a molecular dynamics simulation as a part of the research on the surface crack behavior in thixoformed automobile parts. The microstructure of the grain-size controlled Al-Si alloy consists of primary and eutectic regions. In eutectic regions the crack initiation begins with initial fracture of the eutectic silicon particles and inside other intermetallic phases. Nano-deformation characteristics in the eutectic and primary phase of the grain-size controlled Al-Si alloy were investigated through the molecular dynamics simulation. The primary phase was assumed to be single crystal aluminum. It was shown that the vacancy occurred at the zone where silicon molecules were.

• 한국산업융합학회 논문집
• /
• 제17권3호
• /
• pp.122-135
• /
• 2014

This paper was studied on the horizontal continuous casting of Al-xSi(x=10~15%) aluminum alloy. The experiments of the horizontal continuous casting was carried out by the horizontal continuous casting machine for various casting conditions and investigated on fracture types and mechanisms. Surface defect types for the horizontal continuous casting is also investigated. And the study was carried out that the horizontal continuous casting conditions such as casting temperature, cooling rate, and drawing speed affect the hardness and primary silicon size of Al-xSi(x=10~15%) aluminum rod bar. Casting temperature within this experiment conditions don't affect on the hardness of rod bar but the higher casting temperature is the smaller primary silicon size. The higher cooling rate and drawing speed have the higher hardness and the smaller primary silicon size.