• 플랜트 저널
• /
• 제4권3호
• /
• pp.60-65
• /
• 2008

Power plant industry has been developed at high-capacity, high-technology, and innovation. Steam turbine became the most useful equipment that dominate more than 50% of all the world electricity production. And developed new materials of the turbine blade and extended length of the turbine last blade brought reform in steam turbine performance upgrade. In this paper, when do partial load driving in high-capacity steam turbine, optimum driving method found whether there is something. In operating steam turbine, there is a lot of loss from secondary wake and throttle of the 1st stage nozzle by the biggest leading factor that load fluctuation affects in high-pressure steam turbine performance. Effect of internal efficiency by 1 stage nozzle is the biggest here, but here fluid flow and flow analysis were not yet examined closely definitely. So, Analyzed design data and acceptance performance test result to applying subcritical pressure drum type 560 MW, supercritical-pressure once through type 500 MW, and 800 MW steam turbines actually. In conclusion, at partial load driving, partial arc admission(PAA) is more efficient than full arc admission(FAA) efficiency. This is judged by because increase being proportional with gross energy of stream that is pressure - available energy if pressure of stream that is flowed in to the turbine increases, available energy becomes maximum and turbine efficiency improves. Therefore, turbine performance is that preview that first stage performance fell if decline is serious in partial load because first stage performance changes according to load.

• 한국지반환경공학회 논문집
• /
• 제11권9호
• /
• pp.27-38
• /
• 2010

모형실험과 유한요소법에 의한 수치해석을 통하여 측방변형지반 속에 설치된 매설관에 작용하는 측방토압을 관찰하였다. 모형실험에서는 모형지반 속에 매설관을 설치한 후 모형지반에 측방변형이 발생될 수 있게 모형실험기를 제작하여 실제 지반에서의 상황을 시뮬레이션하였다. 이 모형실험기는 지반의 변형속도를 여러 가지로 조절할 수 있게 제작하였다. 여러 가지 직경과 형상의 매설관에 대하여 실험을 실시함으로써 이들 요인이 측방토압에 미치는 영향을 조사하였다. 모형실험결과 연약지반의 측방유동으로 인하여 매설관에 작용하는 측방하중은 연약지반의 측방변형속도가 빠를수록 크게 작용하였다. 순간재하 조건에 의한 수치해석 결과는 지반변형속도가 중간 정도 빠르기인 0.3mm/min에서 1.0mm/min 사이의 지반변형속도의 조건에서 실시한 모형실험 결과와 유사하였다. 대부분의 모형실험결과 지반변형량이 작은 시점에서 측방하중의 제1항복이 발생하며 이때까지 탄성변형거동을 보이다가 제2항복에 이르기까지 하중이 한 동안 수렴되는 소성거동을 보였다. 지반변형이 계속하여 증가하면 측방하중도 다시 증가하여 압축거동을 보였다. 그러나 빠른 지반변형속도에서의 실험 결과에서는 항복하중에 도달한 후 수렴과정이 없이 계속하여 하중이 증가하였음을 볼 수 있다. 매설관의 직경이 클수록 측방유동 연약지반 속에 설치된 매설관에 작용하는 측방하중의 크기와 하중증가 속도가 컸으며 초기지반변형에서는 측방하중이 매설관의 직경 및 형상의 영향을 적게 받지만 지반변형량이 증가함에 따라 그 영향이 크게 나타났다.

• Tribology and Lubricants
• /
• 제9권2호
• /
• pp.22-28
• /
• 1993

The experimental investigation on the inlet pressure of a large tilting pad journal bearing is studied. The continuous distribution of the film pressure and film thickness are measured along with the shaft speed and bearing load for various flow rates. Considerably large inlet pressure is observed at the entrance of each pad, especially lower pads. The inlet pressure increases with the increase of shaft speed as well as bearing load, but it is almost independent on the folw rate and the oil supply temperature. Because of the inlet pressure, the upper pads always keep up slight wedge film shape which are almost parallel to the journal surface, and spragging is not observed in the upper pads with no preload.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.1020-1025
• /
• 2004

This research reviews the characteristics of earth pressure incurred by GRS-RW mainly used in the railroad design in order to resist large lateral load caused by train and additional load induced by facilities such as noise barrier fences, electric poles, etc. The results of test shows the existence of arching effect that horizontal earth pressure increases in the backfill while earth pressure applying to the wall reduced under GRS-RW system. In both cases, unreinforced wall and GRS-RW system, the coefficient of earth pressure (K) is about 0.4 at the rest. However, after lateral displacement occurs, the earth pressure nearly reduce down to zero under GRS-RW system while the earth pressure decreases up to 0.12 in case of unreinforced retaining wall.

• 드라이브 ㆍ 컨트롤
• /
• 제17권1호
• /
• pp.21-26
• /
• 2020

The load characteristics of a piston pump holder due to the squeeze effect are influenced by the surface shape and gap thickness of the holder (cradle). Therefore, the pressure distribution and the load capacity of the piston pump holder due to the squeeze effect are studied by using the CFD software and the surface shape and gap thickness of the piston pump holder are considered. In order to verify the accuracy of numerical results, the load capacities of a circular plate holder are numerically studied, and the accuracy of numerical results is verified by comparing with the theoretical results. Also, the pressure distribution and load capacity of the rectangular plate holder of a piston pump are obtained by using the CFD software. The results show that the load capacity of the square plate holder with grooves is slightly higher at a low gap thickness, but the effects of the number and arrangement of grooves on the load capacity of the holder are weak. We conclude that the load capacity and the maximum pressure are slightly affected due to the existence of grooves on the holder surface, and the fluid storing effect of the holder surface grooves during the operation is likely to prevent the dry-sticking phenomenon.

• 한국강구조학회 논문집
• /
• 제16권4호통권71호
• /
• pp.453-461
• /
• 2004

국내에서는 아직 철골구조의 베이스플레이트에 대한 설계기준이 작성되어 있지 않으므로 외국 기준 및 자료들을 근거로 중심축하중을 받는 H형강 기둥아래의 베이스플레이트에 대한 ASD 설계식을 제안하고자 한다. 또한 제안된 설계식과 하중을 변화시키며 설계한 예제를 비교한 결과, 보통의 축력을 받을 때에는 플레이트 면이 위험단면 $0.95d{\times}0.8b_f$인 사각형 길이면에 고정시킨 외측캔틸레버 보와 H형강 기둥 내부3변고정 플레이트로 가정한 것 중 위험한 쪽으로 설계한다. 그리고 적은 축력을 받을 때에는 베이스플레이트의 위험단면 및 지압면은 웨브에 면한 기둥 플랜지 사이의 캔틸레버로 설계한다.

• Computers and Concrete
• /
• 제6권5호
• /
• pp.357-376
• /
• 2009

In the design of concrete columns, it is important to provide some nominal flexural ductility even for structures not subjected to earthquake attack. Currently, the nominal flexural ductility is provided by imposing empirical deemed-to-satisfy rules, which limit the minimum size and maximum spacing of the confining reinforcement. However, these existing empirical rules have the major shortcoming that the actual level of flexural ductility provided is not consistent, being generally lower at higher concrete strength or higher axial load level. Hence, for high-strength concrete columns subjected to high axial loads, these existing rules are unsafe. Herein, the combined effects of concrete strength, axial load level, confining pressure and longitudinal steel ratio on the flexural ductility are evaluated using nonlinear moment-curvature analysis. Based on the numerical results, a new design method that provides a consistent level of nominal flexural ductility by imposing an upper limit to the axial load level or a lower limit to the confining pressure is developed. Lastly, two formulas and one design chart for direct evaluation of the maximum axial load level and minimum confining pressure are produced.

• Structural Engineering and Mechanics
• /
• 제46권5호
• /
• pp.735-753
• /
• 2013

The wind load is always the dominant load of cooling tower due to its large size, complex geometry and thin-wall structure. At present, when computing the wind-induced response of the large-scale cooling tower, the wind pressure distribution is obtained based on code regulations, wind tunnel test or computational fluid dynamic (CFD) analysis, and then is imposed on the tower structure. However, such method fails to consider the change of the wind load with the deformation of cooling tower, which may result in error of the wind load. In this paper, the analysis of the large cooling tower based on the iterative method for wind pressure is studied, in which the advantages of CFD and finite element method (FEM) are combined in order to improve the accuracy. The comparative study of the results obtained from the code regulations and iterative method is conducted. The results show that with the increase of the mean wind speed, the difference between the methods becomes bigger. On the other hand, based on the design of experiment (DOE), an approximate model is built for the optimal design of the large-scale cooling tower by a two-level optimization strategy, which makes use of code-based design method and the proposed iterative method. The results of the numerical example demonstrate the feasibility and efficiency of the proposed method.

• Geomechanics and Engineering
• /
• 제14권1호
• /
• pp.61-69
• /
• 2018

The first part shows the optimal contact surface for T-shaped combined footings to obtain the most economical dimensioning on the soil (optimal area). This paper presents the second part of a new model for T-shaped combined footings, this part shows a the mathematical model for design of such foundations subject to axial load and moments in two directions to each column considering the soil real pressure acting on the contact surface of the footing with one or two property lines restricted, the pressure is presented in terms of an axial load, moment around the axis "X" and moment around the axis "Y" to each column, and the methodology is developed using the principle that the derived of the moment is the shear force. The classic model considers an axial load and a moment around the axis "X" (transverse axis) applied to each column, i.e., the resultant force from the applied loads is located on the axis "Y" (longitudinal axis), and its position must match with the geometric center of the footing, and when the axial load and moments in two directions are presented, the maximum pressure and uniform applied throughout the contact surface of the footing is considered the same. To illustrate the validity of the new model, a numerical example is presented to obtain the design for T-shaped combined footings subjected to an axial load and moments in two directions applied to each column. The mathematical approach suggested in this paper produces results that have a tangible accuracy for all problems.

• 대한기계학회논문집A
• /
• 제31권5호
• /
• pp.586-593
• /
• 2007

This paper proposes closed-form plastic limit load solutions for elbow with local wall thinning at extrados under internal pressure. This work was performed using 3-dimensional, small strain FE analyses based on elastic-perfectly plastic materials. The wide range of elbow and local wall thinning geometries are considered. For systematic analyses for effect of axial thinning extent on limit loads, two limiting cases are considered; a sufficiently long thinning, and the circumferential part-through surface crack. Then, the closed-form plastic limit load solutions for intermediate thinning are obtained by using result of two limiting cases. The effect of axial thinning extent for elbow on plastic limit load is highlighted by comparing with that for straight pipes. Although the proposed limit load solutions are developed for the case when local wall thinning exist in the center of elbow, it is also shown that they can be applied to the case when local wall thinning exists anywhere within elbow.