• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.2
• /
• pp.177-183
• /
• 2008

The typical heat-resisting rotor steels such as 2.25CrMo, 9CrMo and 12CrW steel were experimentally studied in order to understand their materials degradation under high temperature and pressure during the long-term service, and then use the basic studies for the structural health monitoring. In order to monitor the materials degradation, it was conducted by the isothermal aging for 2.25CrMo steel, creep-fatigue for 9CrMo steel and creep for 12Cr steel with the incremental step test. The ultrasonic wave properties, electrical resistivity and coercivity were interpreted in relation to microstructural changes at each material and showed strong sensitivity to the specific microstructural evolution.

• Tunnel and Underground Space
• /
• v.27 no.5
• /
• pp.324-332
• /
• 2017

In this paper, a numerical analysis of one-dimensional viscous fluid flow in a rock joint using UDEC code is performed to evaluate the effect of design parameters on injection performance. We consider injection pressure, fluid compressibility, time dependence of yield strength and viscosity of injected grout fluid, and mechanical deformation of joint as the design parameters, and penetration length and flow rate of injection are investigated as the injection performance. Numerical estimations of penetration length and flow rate were compared to analytical solution and were well comparable with each other. We showed that cumulative injection volume can be over-estimated by 1.2 times than the case that the time-dependent viscosity evolution is not considered. We also carried out a coupled fluid flow and mechanical deformation analysis and demonstrated that injection-induced joint opening may result in the increment of cumulative volume by 4.4 times of that from the flow only analysis in which joint aperture is kept constant.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.1
• /
• pp.49.2-49.2
• /
• 2017

Star forming dwarf galaxies in various environments are attractive objects for investigating the environmental effects on chemical evolution of dwarf galaxies. Using SDSS DR7 spectroscopic data and GALEX ultraviolet (UV) imaging data, we study the chemical properties of star forming dwarf galaxies in various environments of the Virgo cluster, Ursa Major group, and field. We derived gas-phase abundance, galaxy mass, and UV specific star formation rate (sSFR) of subsample, early-type (ETD) and late-type star forming dwarf (LTD) galaxies, which are divided by visually classified galaxy morphology. We found no O/H enhancement of LTDs in cluster and group environments compared to the field, implying no environmental dependence of the mass-metallicity relation for LTDs. LTDs in the Virgo cluster and Ursa Major group have similar sSFR at a given galaxy mass, but they exhibit systematically lower sSFR than those in isolated field environment. We suggest that LTDs in the Virgo cluster are an infalling population that was recently accreted from the outside of the cluster. We found that ETDs in the Virgo cluster and Ursa Major group exhibit enhanced O/H compared to those in the field. However, no distinct difference of N/O of galaxies between different environments. The chemically evolved ETDs in the Virgo cluster and Ursa Major group also show similar mass-sSFR relation, but systematically lower sSFR at a fixed galaxy mass compared to the field counterparts. We suggest that ETDs in the Virgo cluster and Ursa Major group have evolved under the similar local environments. We also discuss the evolutionary path of ETDs and LTDs with respect to the environmental effects of ram pressure stripping and galaxy interaction/merging.

• Advances in concrete construction
• /
• v.9 no.6
• /
• pp.537-545
• /
• 2020

In order to reduce the usage of cement slurry in grouting engineering and consume the tunnel excavation waste soil, a new geopolymeric grouting material (GGM) was prepared by combine completely weathered granite (CWG) and blast-furnace slag (BFS), which can be applied to in-situ grouting treatment of completely weathered granite strata. The results showed CWG could participate in the geopolymerization process, and GGM slurry has the characteristics of short setting time, high flowability, low viscosity, high stone rate and high mechanical strength, and a design method of grouting pressure based on viscosity evolution was proposed. By adjusted the content of completely weathered granite and alkali activator concentration, the setting time of GGM were ranged from 5 to 30 minutes, the flowability was more than 23.5 cm, the stone rate was higher than 90%, the compressive strength of 28 days were 7.8-16.9 MPa, the porosity were below 30%. This provides a novel grouting treatment and utilizing excavated soil of tunnels in the similar strata.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.3
• /
• pp.275-285
• /
• 2003

A visualization study on the effect of forcing amplitude in tone-excited jet diffusion flames has been conducted. Visualization techniques are employed using optical schemes. which are a light scattering photography. Flame stability curve is attained according to Reynolds number and forcing amplitude at a fuel tube resonant frequency. Flame behavior is globally grouped into two from attached flame to blown-out flame according to forcing amplitude: one sticks the tradition flame behavior which has been observed in general jet diffusion flames and the other shows a variety of flame modes such as the flame of a feeble forcing amplitude where traditionally well-organized vortex motion evolves, a fat flame. an elongated flame. and an in-burning flame. Particular attention is focused on an elongation flame. which is associated with a turnabout phenomenon of vortex motion and on a reversal of the direction of vortex roll-up. It is found that the flame length with forcing amplitude is the direct outcome of the evolution process of the formed inner flow structure. Especially the negative part of the acoustic cycle under the influence of a strong negative pressure gradient causes the shapes of the fuel stem and fuel branch part and even the direction of vortex roll-up to dramatically change.

• Journal of Powder Materials
• /
• v.17 no.5
• /
• pp.365-372
• /
• 2010

The evolution of sinterability, microstructure and mechanical properties for the spark plasma sintered(SPS) Ti from commercial pure titanium(CP-Ti) was studied. The densification of titanium with 200 mesh and 400 mesh pass powder was achieved by SPS at $750{\sim}1100^{\circ}C$ under 10 MPa pressure and the flowing $H_2$+Ar mixed gas atmosphere. The microstructure of Ti sintered up to $800^{\circ}C$ consisted of equiaxed grains. In contrast, the growth of large elongated grains was shown in sintered bodies at $900^{\circ}C$ with the 400 mesh pass powder and the lamella grains microstructure had been developed by increasing sintering temperature. The Vickers hardness of 240~270 HV and biaxial strength of 320~340 MPa were found for the specimen prepared at $950^{\circ}C$.

• Composites Research
• /
• v.16 no.3
• /
• pp.1-8
• /
• 2003

Densification occurs by the inelastic flow of the matrix materials during the consolidation processes at high temperature for MMCs, and the results depend on many process conditions such as applied pressure, temperature and volume fraction of fiber and matrix materials. This is particularly important in titanium matrix composites since material failure may occur by either the applied conditions or microstructural parameters through the processes, and thus a generic model based on micro-mechanical approaches enabling the evolution of density over time to be predicted has been developed. The mode developed is then implemented into FEM so that practical process simulation has been carried out. Further the experimental investigation of the consolidation behavior of SiC/Ti-6Al-4V composites using vacuum hot pressing has been performed, and the results obtained are compared with the model predictions.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.3
• /
• pp.418-424
• /
• 2015

The chemical response of energetic materials is analyzed in terms of 1) the thermal decomposition under the thermal stimulus and 2) the reactive flow upon the mechanical impact, both of which give rise to an exothermic thermal runaway or an explosion. The present study aims at building a set of chemical kinetics that can precisely model both thermal and impact initiation of a heavily aluminized cyclotrimethylene-trinitramine (RDX) which contains 35% of aluminum. For a thermal decomposition model, the differential scanning calorimetry (DSC) measurement is used together with the Friedman isoconversional method for defining the frequency factor and activation energy in the form of Arrhenius rate law that are extracted from the evolution of product mass fraction. As for modelling the impact response, a series of unconfined rate stick data are used to construct the size effect curve which represents the relationship between detonation velocity and inverse radius of the sample. For validation of the modeled results, a cook-off test and a pressure chamber test are used to compare the predicted chemical response of the aluminized RDX that is either thermally or mechanically loaded.

• Tunnel and Underground Space
• /
• v.30 no.4
• /
• pp.335-358
• /
• 2020

We present a numerical model to simulate coupled hydro-mechanical behavior of fault using TOUGH-FLAC simulator. This study aims to develop a numerical method to estimate fluid injection-induced fault reactivation in low permeability rock and to access the relevant hydro-mechanical stability in rock as part of DECOVALEX-2019 Task B. A coupled fluid flow and mechanical interface model to explicitly represent a fault was suggested and validated from the applications to benchmark simulations and the field experiment at Mont Terri underground laboratory in Switzerland. The pressure build-up, hydraulic aperture evolution, displacement, and stress responses matched those obtained at the site, which indicates the capability of the model to appropriately capture the hydro-mechanical processes in rock fault.

• Korean Journal of Head & Neck Oncology
• /
• v.7 no.1
• /
• pp.24-34
• /
• 1991

Lymphangioma is a benign, growth of lymphatic tissue that is present at birth or develops in early childhood, which may cause serious alterations in growth and developmemt. The problems with facial lymphangioma is usually releated directly to their size and to the area of the face which is involved. The lesions themselves may range from small, localized blemishes to huge facial masses involving both soft tissue and underlying bone and causing great distortion and asymmetry. The facial bones are seldom involved, but the natutal evolution of an individual lesion often cannot be accurately predicted when the child is first seen. Any changes in the underlying facial bone could be due either to a direct growth of the lesion into the bone, or secondary to pressure of the lesion growing outside the bone itself. A case of cystic lymphangioma extending from the neck to the tongue is reported. A six-year-old female was admitted because of swelling of the tongue. At that time, the tongue reportedly reached the extraoral size of 7x5x2.5cm and a soft, diffuse swelling of left anterior neck was revealed. The removal of cystic mass including left neck dissection and partial glossectomy were undertaken. The another case of lymphangioma is located on mandibular cheek. A twenty nine-year-old male was admitted because of palpable mass of the left mandibular area and fissure of palate. The radical excision of mass with mandibulectomy of body were undertuken. Thus we reported such a rare case and reviewed the lymphangioma.