• 펄프종이기술
• /
• 제35권2호
• /
• pp.12-17
• /
• 2003

The effects of wet pressing and drying conditions on the disintegration and physical properties of paper were investigated in order to get the basic information on the resistance of paper for aqueous solution during converting processes. Wet pressing of unbeaten bleached softwood kraft pulp increased WRV at the range of grammage investigated. The increase of WRV with grammage at low wet pressing pressure(50 psi) was obvious, while it was not significant at higher wet pressing pressure(110 psi). The changes of WRV by drying were affected by the grammage and wet pressing pressure. The poorer disintegration of sheet, the higher wet pressing pressure and drying temperature. Although the strength properties were increased with the grammage, wet pressing pressure and drying temperature, results showed different trend from those of beaten pulp.

• 한국분말재료학회지
• /
• 제1권2호
• /
• pp.159-166
• /
• 1994

The variation of the microstructures and the mechanical properties with varying vacuum hot pressing temperature and pressure was investigated in PyM processed 20 vol%) SiCw/ 2124Al composites. As increasing the vacuum hot pressing temperature, the aspect ratio of whiskers and density of composites increased due to the softening of 2124Al matrix with the increased amount of liquid phase. The tensile strength of composite increased with increasing vacuum hot pressing temperature up to $570^{\circ}C$ and became saturated above $570^{\circ}C$, To attain the high densification of composites above 99%, the vacuum hot pressing pressure was needed to be above 70 MPa. However, the higher vacuum hot pressing pressure above 70 MPa was not effective to increase the tensile strength due to the reduced aspect ratio of SiC whiskers from damage of whiskers during vacuum hot pressing. A phenomenological equation to predict the tensile strength of $SiC_w$/2124AI composite was proposed as a function including two microstructural parameters, i.e. density of composites and aspect ratio of whiskers. The tensile strength of $SiC_w$/2124AI were found more sensitive to the porosity than other P/M materials due to the higher stress concentration and reduced load transfer efficiency by the pores locating at whisker/matrix interfaces.

• 한국분말재료학회지
• /
• 제12권4호
• /
• pp.255-260
• /
• 2005

Direct solid state synthesis by hot pressing has been applied in order to produce high efficiency $Zn_4Sb_3$ bulk specimens. Single phase $Zn_4Sb_3$ with 98.5% of theoretical density was successfully produced by direct hot pressing of elemental powders containing 1.2 at.% excess Zn. Thermoelectric properties as a function of temperature were investigated from room temperature to 600 K and compared with results of other studies. Transport properties at room temperature were also evaluated. Thermoelectric properties of single phase $Zn_4Sb_3$ materials produced by direct synthesis were measured and are comparable to the published data. Direct solid state synthesis by hot pressing provides a promising processing route in this material.

• 대한기계학회논문집A
• /
• 제24권3호
• /
• pp.735-742
• /
• 2000

Densification behaviors of mixed metal powder under high temperature were investigated. Experimental data of mixed copper and tool steel powder with various volume fractions of Cu powder were obtained under hot isostatic pressing and hot pressing. By mixing the creep potentials of McMeeking and co-workers and of Abouaf and co-workers originally for pure powder, the mixed creep potentials with various volume fractions of Cu powder were employed in the constitutive models. The constitutive equations were implemented into a finite element program (ABAQUS) to compare with experimental data for densification of mixed powder under hot isostatic pressing and hot pressing. Finite element calculations by using the creep potentials of Abouaf and co-workers agreed reasonably well with experimental data, however, those by McMeeking and co-workers underestimate experimental data as observed in the case of pure metal powders.

• 대한기계학회논문집A
• /
• 제32권4호
• /
• pp.333-339
• /
• 2008

Densification behavior of copper powder was investigated to study the effect of an aluminum mold under warm pressing. The low flow stress of an aluminum mold is appropriate to apply hydrostatic stress to powder compacts during compaction under high temperature. The suggested powder metallurgy process is very useful under high temperature since copper powder compacts have higher relative density over axial stress of 100 MPa and show more homogeneity as compared with conventional warm pressing. Elastoplastic constitutive equation proposed by Shima and Oyane was implemented into a finite element program (ABAQUS) for densification behavior under warn pressing by using a metal mold. Finite element results agreed well with experimental data for densification and deformation of copper powder compacts in the mold.

• Journal of the Korean Wood Science and Technology
• /
• 제25권1호
• /
• pp.50-55
• /
• 1997

This study was carried out to utilize old newspaper(ONP) and paper sludge more effectively, and also to elucidate the influences of pressing conditions on the medium density fiberboard(MDF) properties. MDFs were made from ONP and low grade of paper sludge by wet process with change of pressing time, temperature and pressure. MDFs of ONP were more affected by pressing conditions, especially pressing pressure, but temperature and pressing time were also important. According to mixing paper sludge to ONP tensile and bending strength of MDF were decreased, but density and dimensional stability were improved. These results indicated that some physical properties of MDF can be improved by paper sludge and it is possible to use it in MDF.

• 한국가구학회지
• /
• 제20권5호
• /
• pp.490-503
• /
• 2009

The objective of this work was to investigate the mechanism of heat transfer in hot-pressing process for MDF manufacturing by reference study. Firstly, general heat transfer theory was studied. The numerical analysis of heat transfer in hot-pressing process was studied on temperature profile, moisture profile, physical properties between moisture and board. The mechanism of heat and moisture transfer inside of board was analyzed by conduction, convection, radiation and diffusion of bound water in wood cell walls. Especially, the change of core temperature as hot press time was important factor to setup hot-pressing schedule in MDF manufacturing.

• 대한기계학회논문집A
• /
• 제21권1호
• /
• pp.73-82
• /
• 1997

High temperature densification behaviors of alumina powder compacts were investigated under hot pressing and hot isostatic pressing. An alumina part of valve-head shape was fabricated under hot pressing and its forming process was simulated by finite element calculation. an alumina powder compact encapsulated by a stainless steel container was also densified under hot isostatic pressing. Inhomogeneous deformations during hot isostatic pressing due to the canning effect were observed experimentally and predicted by finite element analysis.

• 한국재료학회지
• /
• 제15권7호
• /
• pp.473-479
• /
• 2005

Thermoelectric $Zn_4Sb_3$ alloys were synthesized by a conventional powder metallurgy process consisting of solid state reaction and hot pressing. Single phase $Zn_4Sb_3$ was successfully produced by the annealing of cold compact starting with the mixed elemental powders, and subsequent hot pressing yielded single phase bulk specimens without microcracks. Phase transformations in this alloy system during synthesis were investigated using XRD, SEM and EDS. Thermoelectric properties as a function of temperature were investigated from room temperature to 600 K and compared with results of analogue studies. Transport properties at room temperature were also evaluated. Thermoelectric properties of single phase $Zn_4Sb_3$ materials produced by this process are comparable to the published data. Synthesis by solid state reaction and hot pressing offers a potential processing route to produce a bulk $Zn_4Sb_3$.ٓ

• Journal of the Korean Wood Science and Technology
• /
• 제46권2호
• /
• pp.132-142
• /
• 2018

An elephant digests only around 30~45% of what it consumes; therefore the undigested material mainly passes as intact fibres. Elephant food is usually composed of grass, leaves, twigs, bark, fruit and seed pods. This research aimed to utilize the elephant dung fibers as material for composite board and citric acid as a bonding agent. Citric acid contents in this research were set at 0 wt% (binderless composite board), 10 wt%, 20 wt%, and 30 wt% based on dry weight particles, while the target density was set at $0.8g/cm^3$. Pressing temperatures were set at $180^{\circ}C$ and $200^{\circ}C$ with the pressing time was 10 minutes. Physical and mechanical properties tests were then performed according to Japanese Industrial Standard A 5905. The result showed that elephant dung fibers could be used as potential materials for composite board. Addition of citric acid and pressing temperature significantly increased the quality of composite board. Infrared analysis indicated that the presence of ester linkages much higher with the increasing of citric acid content and pressing temperature. The optimum properties of composite board made from elephant dung fibers could be achieved at pressing temperature of $200^{\circ}C$ and a citric acid content of 20 wt%.