• Journal of Navigation and Port Research
• /
• v.31 no.7
• /
• pp.597-603
• /
• 2007

A predictive controller can solve a control problem related to a disturbance-dominant system such as roll stabilization of a ship in waves. In this paper, a predictive controller is developed for a fin stabilizer. Future wave-induced moment is modeled simply using two typical regular wave components for which six parameters are identified by the recursive Fourier transform and the least squares method using the past time series of the roll motion. After predicting the future wave-induced moment, optimal control theory is applied to discover the most effective command fin angle that will stabilize the roll motion. In the results, wave prediction performance is investigated, and the effectiveness of the predictive controller is compared to a conventional PD controller.

• Journal of Power Electronics
• /
• v.13 no.6
• /
• pp.1016-1023
• /
• 2013

Predictive current control offers the potential for achieving more precise current control with a minimum of distortion and harmonic noise. However, the predictive method is difficult to implement and has a greater computational burden. This paper introduces a theoretical analysis and experimental verification for an improved predictive current control technique applied to single phase grid connected voltage source inverters (VSI). The proposed technique has simple calculations. An ATmega1280 microcontroller board is used to implement the proposed technique for a simpler and cheaper control system. To enhance the current performance and to obtain a minimum of current THD, an improved tri-level PWM switching strategy is proposed. The proposed switching strategy uses six operation modes instead of four as in the traditional strategy. Simulation results are presented to demonstrate the system performance with the improved switching strategy and its effect on current performance. The presented experimental results verify that the proposed technique can be implemented using fixed point 8-bit microcontroller to obtain excellent results.

• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.497-508
• /
• 2019

The predictive speed control (PSC) strategy can realize the simultaneous control of speed and current by using one cost function. As a model-based control method, the performance of the PSC is vulnerable to model mismatches such as load torque disturbances and parameter uncertainties. To solve this problem, this paper presents a robust predictive speed control (RPSC) strategy for surface-mounted permanent magnet synchronous motor (SPMSM) drives. The proposed RPSC uses extended state observers (ESOs) to estimate the lumped disturbances caused by load torque changes and parameter mismatches. The observer-based prediction model is then compensated by using the estimated disturbances. The introduction of ESOs can achieve robustness against predictive model uncertainties. In addition, a modified cost function is designed to further suppress load torque disturbances. The performance of the proposed RPSC scheme has been corroborated by experimental results under the condition of load torque changes and parameter mismatches.

• Journal of Korea Multimedia Society
• /
• v.19 no.1
• /
• pp.1-9
• /
• 2016

In this paper, we propose a method of measuring bone mineral density in a peripheral-type clinical X-ray CT using a phantom, and we propose a method of classifying osteoporosis using bone mineral density and bone structure parameters together. It segments the trabecular bone region and cortical bone region for the six sections of the phantom and calculates the average HU value of the segmented regions. By using these values, it derives an expression converting HU value to bone mineral density. It segments trabecular bone of 1 cm region in the end part of distal radius and extracts the bone mineral density and structural parameters for the trabecular bone region. We extracted bone mineral density and structural parameters for the 18 subjects each of normal and osteoporotic group. We carried out classification experiments using three classification methods; SAD, SVM, ANN. The sensitivity, specificity, accuracy, positive predictive value, negative predictive value, likelihood ratio of the classification was improved in the order of ANN, SVM and SAD. Also, The sensitivity, specificity, accuracy, positive predictive value, negative predictive value, likelihood ratio of the classification was improved when we use the bone mineral density and structural parameters together.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.179-189
• /
• 2019

Four-quadrant converters (4QCs) are widely used as AC-DC power conversion interfaces in many areas. A control delay commonly exists in the digital implementation process of 4QCs, especially for high power 4QCs with a low switching frequency. This usually results in alternating current distortion, increased current harmonic content and system instability. In this paper, the control delay is divided into a computation delay and a PWM delay. The impact of the control delay on the performance of a 4QC is briefly analyzed. To obtain a fundamental value of AC current that is as accurately as possible, a specific sampling method considering the PWM pattern is introduced. Then a current predictive control based on a modified z-transform is proposed, which is effective in reducing the control delay and easy in terms of digital implementation. In addition, it does not depend on object models and parameters. The feasibility and effectiveness of the proposed predictive current control method is verified by simulation and experimental results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.1
• /
• pp.9-16
• /
• 2018

Predictive control is a very practical method that obtain the current input that minimizes the future errors of the reference command and state by use of the predictive model of the controlled object, and can also consider the constraints of the state and input. Although there have been studies in which predictive control is applied to mobile robots, performance has not been optimized as various control parameters for determining control performance have been arbitrarily specified. In this paper, we apply the genetic algorithm to the trajectory tracking control of a mobile robot with input constraints in order to minimize the trajectory tracking errors through control parameter tuning, and apply the quadratic programming Hildreth method to reflect the input constraints. Through the computer simulation, the superiority of the proposed method is confirmed by comparing with the existing method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.5
• /
• pp.415-421
• /
• 2014

This study proposes a model-based predictive control for interleaved multi-phase DC/DC converters. The power values necessary to adjust the output voltage in the succeeding are predicted using a converter model. The output power is controlled by selecting the optimal duty cycle. The proposed method does not require controller loops and modulators for converter switching. This method can control the converter by calculating the optimal duty cycle, which minimizes the error between the reference and actual output voltage. The effectiveness of the proposed method is verified through simulations and experiments.

• Proceedings of the KIEE Conference
• /
• 2000.11d
• /
• pp.621-623
• /
• 2000

In this paper, the effective design method of the predictive controller using fuzzy neural networks(FNNs) is presented for the Intelligent control of chaotic nonlinear systems. In our design method of controller, predictor parameters are tuned by the error value between the actual output of a chaotic nonlinear system and that of a fuzzy neural network model. And the parameters of predictive controller using fuzzy neural network are tuned by the gradient descent method which uses control error value between the actual output of a chaotic nonlinear system and the reference signal. In order to evaluate the performance of our controller, it is applied to the Duffing system which are the representative continuous-time chaotic nonlinear systems and the Henon system which are representative discrete-time chaotic nonlinear systems.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.344-349
• /
• 1990

Under the assumption that process input/output data are sufficiently rich to allow reasonable plant identification, a long-range predictive control method for SISO bilinear plant is derived. In order to ensure offset-free behaviour of the control method, a new bilinear CARIMA model with variable dead-time is introduced. Furthermore, to extend the maximum output prediction horizon, the future predicted outputs in the bilinear term are assumed to be equal to the known future set-points. With a classical recursive adaptation algorithm, the proposed control scheme is capable of stable control of bilinear plants with variable parameters, with variable dead-time, and with a model order which changes instantaneously. Several simulation results demonstrate the characteristics of the proposed bilinear model predictive control method.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.1
• /
• pp.1-5
• /
• 2020

In this paper, a predictive maintenance of the robot trouble using the machine learning method, so called MT(Mahalanobis Taguchi), was studied. Especially, 'MD(Mahalanobis Distance)' was used to compare the robot arm motion difference between before the maintenance(bearing change) and after the maintenance. 6-axies vibration sensor was used to detect the vibration sensing during the motion of the robot arm. The results of the comparison, MD value of the arm motions of the after the maintenance(bearing change) was much lower and stable compared to MD value of the arm motions of the before the maintenance. MD value well distinguished the fine difference of the arm vibration of the robot. The superior performance of the MT method applied to the prediction of the robot trouble was verified by this experiments.