• Magazine of the Korean Society of Agricultural Engineers
• /
• v.38 no.3
• /
• pp.70-81
• /
• 1996

Solutions of geotechnical engineering problems require predictions of deformation and stresses during various stages of loading. Powerful numerical methods are available to make such predictions even for complicated problems. To get accurate results, realistic stress-strain relationships of soils are dependent on a number of factors such as soil type, density, stress level and stress path. Attempts are continuously being made to develope analytical models for soils incorporating all such factors. Isotropic compression-expansion test and a series of drained conventional triaxial tests with several stress path for Baekma river sand were performed to investigate stress-strain and volume change characteristics of Lade's single work hardening model dependant on the stress path. In order to predicted of stress-strain and volumetric strain behavior were determined the values of parameters for the mode by the computer program based on the regression analysis. Predicted stress-strain behavior of triaxial compression tests and optional stress path tests for increasing confining pressure with parameters obtained conventional triaxial compression tests agreed with several test results but the prediction results for decreasing confining pressure reduced triaxial compression tests make a little difference with test results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.12
• /
• pp.1140-1147
• /
• 2013

In this paper, The path loss model of Air Traffic Control(ATC) telecommunication radio channel has been studied at the Incheon International Airport(IIA) Cargo Terminal. We measured one frequency among VHF channel bands. The transmitting site was located at different locations with different heights. The transmitting site radiated the Continuous Wave(CW). The propagation measurement was taken using the moving vehicle equipped with receiver and antenna. The transmitting power, frequency and antenna height are the same as the current operating condition. The path loss exponent and intercept parameters were extracted by the basic path loss model and hata model. The path loss exponent at IIA Cargo terminal area were 3.67 and 3.39 respectively in first and second transmitting sites. The deviation of prediction error is 14.42 and 10.38. The new path loss equation at the IIA Cargo terminal area was also developed using the derived path loss parameters. The new path loss was compared with other models. This result will be helpful for the ATC site selection and service quality evaluation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.5
• /
• pp.988-995
• /
• 2009

One of the most popular services of Telematics is a shortest path finding from a starting point to a destination. In this paper, a dynamic shortest path finding system with forecasting result of traffic flow in the future was developed and various experiments to verify the performance of our system using real-time traffic information has been conducted. Traffic forecasting has been done by a prediction system using Bayesian network. It searched a dynamic shortest path, a static shortest path and an accumulated shortest path for the same starting point and destination and calculated their travel time to compare with one of its real shortest path. From the experiment, over 75%, the travel time of dynamic shortest paths is the closest to one of their real shortest paths than one of static shortest paths and accumulated shortest paths. Therefore, it is proved that finding a dynamic shortest path by applying traffic flows in the future for intermediated intersections can give more accurate traffic information and improve the quality of services of Telematics than finding a static shortest path applying by traffic flows of the starting time for intermediated intersections.

• Journal of Communications and Networks
• /
• v.11 no.4
• /
• pp.337-349
• /
• 2009

In this paper, we introduce a novel mobility model for mobile sinks in which the sinks move towards randomly distributed destinations, where each destination is associated with a mission. The novel mobility model is termed the random mobility with destinations. There have been many studies on mobile sinks; however, they merely support two extreme cases of sink mobility. The first case features the most common and general mobility, with the sinks moving randomly, unpredictably, and inartificially. The other case takes into account mobility only along predefined or determined paths such that the sinks can gather data from sensor nodes with minimum overhead. Unfortunately, these studies for the common mobility and predefined path mobility might not suit for supporting the random mobility with destinations. In order to support random mobility with destination, we propose a new protocol, in which the source nodes send their data to the next movement path of a mobile sink. To implement the proposed protocol, we first present a mechanism for predicting the next movement path of a mobile sink based on its previous movement path. With the information about predicted movement path included in a query packet, we further present a mechanism that source nodes send energy-efficiently their data along the next movement path before arriving of the mobile sink. Last, we present mechanisms for compensating the difference between the predicted movement path and the real movement path and for relaying the delayed data after arriving of the mobile sink on the next movement path, respectively. Simulation results show that the proposed protocol achieves better performance than the existing protocols.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.9
• /
• pp.765-772
• /
• 2013

In this paper, we studied the path loss model of Air Traffic Control(ATC) telecommunication radio channel at the Incheon International Airport(IIA) concourse area. We measured wave propagation characteristics on the two frequencies among VHF/UHF channel bands. The transmitting site radiated the Continuous Wave(CW). The propagation measurement was taken using the moving vehicle equipped with receiver and antenna. The transmitting power, frequency, and antenna height are the same as the current operating condition. The path loss exponent and intercept parameters were extracted by the basic path loss model and hata model. The path loss exponents at Concourse area were 3.1/3.13 and 3.01/3.38 respectively in 128.2MHz and 269.1MHz. The deviation of prediction error is 2.77/3.17 and 4.01/3.66. The new path loss equation at the Concourse area was also developed using the derived path loss parameters. The new path loss model was compared with other models. This result will be helpful for the ATC site selection and service quality evaluation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.11
• /
• pp.763-770
• /
• 2022

In an environment where multiple drones are operated, collisions can occur when path points overlap, and collision avoidance in preparation for this is essential. When multiple drones perform multiple tasks, it is not appropriate to use a method to generate a collision-avoiding path in the path planning phase because the path of the drone is complex and there are too many collision prediction points. In this paper, we generate a path through a commonly used path generation algorithm and propose a collision avoidance method using speed profile optimization from that path segment. The safe distance between drones was considered at the expected point of collision between paths of drones, and it was designed to assign a speed profile to the path segment. The optimization problem was defined by setting the distance between drones as variables in the flight time equation. We constructed the constraints through linearize and convexification, and compared the computation time of SQP and convex optimization method in multiple drone operating environments. Finally, we confirmed whether the results of performing convex optimization in the 20 drone operating environments were suitable for the multiple drone operating system proposed in this study.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.5 s.96
• /
• pp.541-548
• /
• 2005

The research deals with the prediction and the measurement of electromagnetic wave propagation in rectangular shaped tunnels at f=2.65 GHz. The received power level was measured in the straight and the curved tunnel by using a spectrum analyzer and Satellite DMB mobile phone. Thus we have gotten the data for two cases, the straight and the curved tunnel whose radius is 300m. In addition, the prediction of wave propagation was conducted based on the ray-launching method, in same tunnel where measurement was performed. A good agreement of the measured and the predicted path loss could be confirmed. The measured path loss shows a marked difference in propagation loss: the path-loss exponent, 3.21, and 3.98, for a straight and a curved tunnel, respectively. The reason that path-loss exponent is high in a curved tunnel is that there is no direct wave but only the reflected waves, which attenuates rapidly with distance due to multiple reflections. Also the predicted path loss shows path loss exeponent, 3.2 and 3.95, for a straight and a curved tunnel which are similar to the simulation results.

• Journal of Korean Society of Transportation
• /
• v.27 no.5
• /
• pp.209-221
• /
• 2009

Travel time estimation under given traffic conditions is important for providing drivers with travel time prediction information. But the present expressway travel time estimation process cannot calculate a reliable travel time. The objective of this study is to estimate the path travel time spent in a through lane between origin tollgates and destination tollgates on an expressway as a prerequisite result to offer reliable prediction information. Useful and abundant toll collection system (TCS) data were used. When estimating the path travel time, the path travel time is estimated combining the link travel time obtained through a preprocessing process. In the case of a lack of TCS data, the TCS travel time for previous intervals is referenced using the linear interpolation method after analyzing the increase pattern for the travel time. When the TCS data are absent over a long-term period, the dynamic travel time using the VDS time space diagram is estimated. The travel time estimated by the model proposed can be validated statistically when compared to the travel time obtained from vehicles traveling the path directly. The results show that the proposed model can be utilized for estimating a reliable travel time for a long-distance path in which there are a variaty of travel times from the same departure time, the intervals are large and the change in the representative travel time is irregular for a short period.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.187-194
• /
• 2002

It has been reported that cracks in mechanical joints is generally under mixed-mode and there is critical inclined angle at which mode I stress intensity factor becomes maximum. The crack propagates in arbitrary direction and thus the prediction of crack growth path is needed to provide against crack propagation or examine safety. In order to evaluate the fatigue life of cracks in mechanical joints, horizontal crack normal to the applied load and located on minimum cross section is major concern but critical inclined crack must also be considered. In this paper mixed-mode fatigue crack growth test is performed far horizontal crack and critical inclined crack in mechanical joints. Fatigue crack growth path is predicted by maximum tangential stress criterion using stress intensity factor obtained from weight function method, and fatigue crack growth rates of horizontal and inclined crack are compared.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.286-291
• /
• 2001

Applications of bonded dissimilar materials such as IC package, ceramic/metal and resin/metal bonded joints, are very increasing in various industry fields. It is very important to analyze the thermal stress and stress singularity at interface edges in bonded joints of dissimilar materials. In orer to understand the package crack emanating from the edge of Die pad and Resin, fracture mechanics of bonded dissimilar materials and material properties are obtained. In this paper, the thermal stress and its singularity index for the IC package were analyzed using 2-dimensional elastic boundary element method. Crack propagation angle and path by thermal stress were numerically simulated with boundary element method.