• Current Photovoltaic Research
• /
• v.3 no.1
• /
• pp.21-26
• /
• 2015

High efficiency $Cu(In,Ga)Se_2$ solar cells are generally prepared above $500^{\circ}C$. Lowering the process temperature can allow wider selection of substrate material and process window. In this paper, the three-stage co-evaporation process widely used to grow CIGS thin film at high temperature was modified to reduce the maximum substrate temperature. Below $400^{\circ}C$ the CIGS films show poor crystal growth and lower solar cell performance, in spite of external Na doping by NaF. As a new approach, Cu source instead of Cu with Se in the second stage was applied on the $(In,Ga)_2Se_3$ precursor at $400^{\circ}C$ and achieved a better crystal growth. The distribution of Ga in the films produce by new method were investigated and solar cells were fabricated using these films.

• Journal of Microbiology and Biotechnology
• /
• v.22 no.10
• /
• pp.1446-1451
• /
• 2012

Levodopa or L-3,4-dihydroxyphenylalanine (L-DOPA) is the precursor of the neurotransmitter dopamine. L-DOPA is a famous treatment for Parkinson's disease symptoms. In this study, electroenzymatic synthesis of L-DOPA was performed in a three-electrode cell, comprising a Ag/AgCl reference electrode, a platinum wire auxiliary electrode, and a glassy carbon working electrode. L-DOPA had an oxidation peak at 376 mV and a reduction peak at -550 mV. The optimum conditions of pH, temperature, and amount of free tyrosinase enzyme were pH 7, $30^{\circ}C$, and 250 IU, respectively. The kinetic constant of the free tyrosinase enzyme was found for both cresolase and catacholase activity to be 0.25 and 0.4 mM, respectively. A cyclic voltammogram was used to investigate the electron transfer rate constant. The mean heterogeneous electron transfer rate ($k_e$) was $5.8{\times}10^{-4}$ cm/s. The results suggest that the electroenzymatic method could be an alternative way to produce L-DOPA without the use of a reducing agent such as ascorbic acid.

• Environmental Analysis Health and Toxicology
• /
• v.26
• /
• pp.11.1-11.6
• /
• 2011

Objects: The prevalence of asthma has increased in recent decades globally. The objective of the present study is to elucidate whether hospitalization for bronchiolitis in infancy and low socioeconomic status interact for bronchial hyperreactivity during teenage years. Method: We studied 522 children age 13-14 years attending schools in rural and urban areas to investigate the risk factors for bronchial hyperreactivity (BHR), defined as a provocation concentration of methacholine that causes a decrease of 20% ($PC_{20}$) in forced expiratory volume within 1 second. Clinical examination, skin prick test, spirometry, and methacholine challenge were performed on all study subjects, who provided written consent. We used multivariate logistic regression to investigate the risk factors for BHR, and analyze the interaction between hospitalization for bronchiolitis in infancy and low socioeconomic status. Results: Forty-six (10.3%) positive BHR cases were identified. In the multivariate logistic analysis, as independent predictors of BHR, adjusted odds ratio of bronchiolitis diagnosed before 2 years of age in low income families was 13.7 (95% confidence interval, 1.4 to 135.0), compared to reference group, controlling for age, gender, parental allergy history, skin prick test, and environmental tobacco smoke (ETS) exposure. Interaction was observed between bronchiolitis before 2 years old and low socioeconomic status on children's bronchial hyperreactivity (p-interaction=0.025). Conclusions: This study showed that bronchiolitis diagnosed before 2 years of age and low socioeconomic status interacted on children's bronchial hyperreactivity. Prevention of acute respiratory infection in early childhood in low socioeconomic status is important to prevent BHR as a precursor of asthma.

• Reproductive and Developmental Biology
• /
• v.33 no.3
• /
• pp.183-187
• /
• 2009

This study analyzed change of proteins in granulosa cells during the porcine follicuar development by proteomics techniques. Granulosa cells of the follicles, of which the diameter is $2{\sim}4\;mm$ and $6{\sim}10\;mm$, were collected from ovary of slaughtered pig that each follicle of diameter $1{\sim}4\;mm$ and $6{\sim}10\;mm$. We extracted glanulosa cell proteins by M-PER Mammalian Protein Extraction Reagent. Proteins were refined by clean-up kit and quantified by Bradford method until total protein was $200{\mu}l$. Immobilized pH gradient(IPG) strip used 18 cm, $3{\sim}10\;NL$. SDS-PAGE used 10% acrylamide gel. After silver staining, Melanie 7 and naked eye test were used for spot analyzation. Increasing proteins in glanulosa cell of $6{\sim}10\;mm$ follicle were 7 spots. This spots were analyzed by MALDI-TOF MS and searched on NCBInr. In results, 7 spots were similar to zinc/ling finger protein 3 precursor (RING finger protein 203), angiomotin, heat shock 60 kDa protein 1 (chaperonin) isoform 1 (HSP60), similar to transducin-like enhancer protein 1 (TLE 1), SH3 and PX domains 2A (SH3PXD2A). Those proteins were related with transfer between cells. Increase of proteins has an effect on follicular development.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.2
• /
• pp.1555-1562
• /
• 2015

Metal oxide semiconductors have been applied in several areas, such as solar cells, sensor, optical elements and displays, due to the high surface area, unique electrical and optical characteristics. Zinc oxide among the metal oxide has excellent physicochemical properties. Zinc oxide is a n-type semiconductor with a wide direct transition band gap of 3.37 eV at room temperature and large exciton binding energy of 60 meV. Cation-doped zinc oxide studies were conducted to complement the electrical and optical characteristics. In this paper, Al-doped ZnO was synthesized by hydrothermal synthesis using microwaves. ZnO was synthesized by adjusting the precursor ratio and using different dopants. The optimal ZnO synthesis conditions for crystal shape and optical properties were determined. The optical properties of aluminum doped zinc oxide were then examined by SEM, XRD, PL, UV-vis absorbance spectrum, and EDS.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.111-111
• /
• 2007

Further scaling the semiconductor devices down to low dozens of nanometer needs the extremely shallow depth in junction and the intentional counter-doping in the silicon gate. Conventional ion beam ion implantation has some disadvantages and limitations for the future applications. In order to solve them, therefore, plasma source ion implantation technique has been considered as a promising new method for the high throughputs at low energy and the fabrication of the ultra-shallow junctions. In this paper, we study about the effects of DC bias and base pressure as a process parameter. The diluted mixture gas (5% $PH_3/H_2$) was used as a precursor source and chamber is used for vacuum pressure conditions. After ion doping into the Si wafer(100), the samples were annealed via rapid thermal annealing, of which annealed temperature ranges above the $950^{\circ}C$. The junction depth, calculated at dose level of $1{\times}10^{18}/cm^3$, was measured by secondary ion mass spectroscopy(SIMS) and sheet resistance by contact and non-contact mode. Surface morphology of samples was analyzed by scanning electron microscopy. As a result, we could accomplish the process conditions better than in advance.

• KSTLE International Journal
• /
• v.6 no.2
• /
• pp.39-44
• /
• 2005

Friction and wear properties of the Boron carbide ($B_{4}C$) coating 100 nm thickness were studied under various relative humidity (RH). The boron carbide film was deposited on silicon substrate by DC magnetron sputtering method using $B_{4}C$ target with a mixture of Ar and methane ($CH_4$) as precursor gas. Friction tests were performed using a reciprocation type friction tester at ambient environment. Steel balls of 3 mm in diameter were used as counter-specimen. The results indicated that relative humidity strongly affected the tribological properties of boron carbide coating. Friction coefficient decreased from 0.42 to 0.09 as the relative humidity increased from $5\%$ to $85\%$. Confocal microscopy was used to observe worn surfaces of the coating and wear scars on steel balls after the tests. It showed that both the coating surface and the ball were significantly worn-out even though boron carbide is much harder than the steel. Moreover, at low humidity ($5\%$) the boron carbide showed poor wear resistance which resulted in the complete removal of coating layer, whereas at the medium and high humidity conditions, it was not. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) analyses were performed to characterize the chemical composition of the worn surfaces. We suggest that tribochemical reactions occurred during sliding in moisture air to form boric acid on the worn surface of the coating. The boric acid and the tribochemcal layer that formed on steel ball resulted in low friction and wear of boron carbide coating.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.480-480
• /
• 2010

In the present work, we studied effect of the deposition parameters on the structure and properties of ZnO films deposited by DC arc plasmatron. The varied parameters were gas flow rates, precursor composition, substrate temperature and post-deposition annealing temperature. Vapor of Zinc acetylacetone was used as source materials, oxygen was used as working gas and argon was used as the cathode protective gas and a transport gas for the vapor. The plasmatron power was varied in the range of 700-1,500 watts. Flow rate of the gases and substrate temperature rate were varied in the wide range to optimize the properties of the deposited coatings. After deposition films were annealed in the hydrogen atmosphere in the wide range of temperatures. Structure of coatings was investigated using XRD and SEM. Chemical composition was analyzed using x-ray photo-electron spectroscopy. Sheet conductivity was measured by 4-point probe method. Optical properties of the transparent ZnO-based coatings were studied by the spectroscopy. It was shown that deposition by a DC Arc plasmatron can be used for low-cost production of zinc oxide films with good optical and electrical properties. Sheet resistance of 4 Ohms cm was achieved after the deposition and 30 min annealing in the hydrogen at $350^{\circ}C$. Elevation of the substrate temperature during the deposition process up to $350^{\circ}C$ leads to decreasing of the film's resistance due to rearrangement of the crystalline structure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.397-397
• /
• 2010

Bone is considered as hierarchically organized biocomposites of organic (collagen) and inorganic (hydroxyapatite) materials. The precise structural dependence between hydroxyapatite (HAp, $Ca_{10}(PO_4)_6(OH)_2)$ crystals and collagen fibril is critical to unique characteristics of bone. To meet those conditions and obtain optimal properties, it is essential to understand and control the initial growth mechanisms of hydroxyapatite at the molecular level, such as other nano-structured materials. In this study, collagen fibrils were prepared by adsorbing native type I collagen molecules onto hydrophobic surface. Hydrophobicity was introduced on the Si wafer surface by using PECVD (plasma enhanced chemical vapor deposition) method and cyclohexane as a precursor. Biomimetic nucleation and growth of HAp on the self-assembled collagen nanofibrils were occurred through incubation of the sample in SBF (simulated body fluid). Chemical and morphological evolution of HAp nanocrystals was investigated by surface-sensitive analytical techniques such as ToF-SIMS (Time-of-Flight Secondary Ion Mass Spectrometry) and AFM (Atomic Force Microscopy) in the early growth stages (< 24 hrs). The very initial stages (< 12 hrs) of mineralization could be clearly demonstrated by ToF-SIMS chemical mapping of surface. In addition to ToF-SIMS and AFM measurement, scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction analysis were conducted to characterize the HAp layer in the late stages. This study is of great importance in the growth of real bone-like materials with a structure analogous to that of natural bones and the development of biomimetic nanomaterials.

• Applied Science and Convergence Technology
• /
• v.25 no.5
• /
• pp.88-91
• /
• 2016

The $Pb[(Mg_{1/3}Ta_{2/3})_{0.7}Ti_{0.3}]O_3$+xwt%PbO systems at temperature of $1250^{\circ}C$ for 4 hours was successful synthesized. In this study, PbO-doped $Pb[(Mg_{1/3}Ta_{2/3})_{0.7}Ti_{0.3}]O_3$ systems with non-linear behaviors showed ordering-degree dependence at the low temperature range were prepared using the columbite precursor method. And the characteristic of remnant polarization vs. electric field were analyzed. The pyroelectric, dielectric and piezoelectric properties of partially disordered $Pb[(Mg_{1/3}Ta_{2/3})_{0.7}Ti_{0.3}]O_3$+xwt%PbO solid solutions were studied as a function of temperature, frequency, and electric field. It showed distinct features of temperature dependent of pyroelectric coefficient, spontaneous polarization and dielectric constant at about $50^{\circ}C$. The figure of merit was calculated as pyroelectric coefficient, dielectric constant and dissipation factor. It was found that the high voltage responsivity FV, high detectivity FD were $0.0373m^2/C$ and $0.6735{\times}10^{-4}Pa{-1/2}$, respectively, in the $Pb[(Mg_{1/3}Ta_{2/3})_{0.7}Ti_{0.3}]O_3$+3.0 wt%PbO system.