• 펄프종이기술
• /
• 제48권1호
• /
• pp.27-33
• /
• 2016

This study was carried out in order to investigate the effect of binder properties in pre-coating layer on the characteristics of top-coating layer and print mottle of coated paper. Four different latices were used as a binder in pre-coating layer, and coating color prepared with a same formulation was applied for top-coating. The properties and print mottle of coated paper were evaluated. It was found that glass transition temperature (Tg) was the important factor to control the properties of pre- and top-coating layer. PPS roughness of coated paper was decreased and paper gloss was increased with applying binder which has lower Tg. Properties of top-coating layer were affected by the binder used in pre-coating layer. Print mottle of coated paper was improved with using binder which has lower Tg in pre-coating layer. These results indicate that final printability and properties of top-coating layer can be improved with using suitable binder in pre-coating layer.

• 펄프종이기술
• /
• 제48권2호
• /
• pp.61-67
• /
• 2016

This study was carried out in order to investigate the effect of pigment properties in a pre-coating layer on the characteristics of a top-coating layer and the print mottle of the coated paper. Five different pigments were applied for this study as raw materials for the pre-coating layer. The properties and print mottle of the coated paper samples were evaluated according to the coating color formulation. Type of pigments appliied in a pre-coating layer was one of the most important factor to control the properties of pre and top coating layer. Surface properties of pre and top coated paper were improved by blending GCC which had smaller particle size, with clay. Properties of a top-coating layer was affected by the pigment properties used in the pre-coating layer. It was found that print mottle of coated paper can be improved by replacing part of GCC with smaller particle size GCC or clay in pre-coating layer.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2011년도 춘계학술발표회 논문집
• /
• pp.251-263
• /
• 2011

This study was carried out in order to investigate the effect of pre-coating layer on top-coating layer. The coated paper with five different formulations were prepared. The properties of coated paper were measured and correlation between pre and top-coated layer was evaluated. Paper gloss was increased with addition of clay and GCC that has smaller particle size. Roughness was decreased with using smaller particle GCC, clay and talc. The highest thickness was obtained with talc. Brightness and whiteness of pre-coated layer were affected to top-coated layer. GCC 60 shows the highest and ununiform water adsorption during 1sec. The adsorption was higher with increasing coated weight. Talc shows the excellent water adsorption properties due to its wettability. These results indicate that final printability and properties of top coating layer can be controlled with adjusting pre-coating layer.

• Corrosion Science and Technology
• /
• 제22권4호
• /
• pp.297-303
• /
• 2023

This study aimed to evaluate hydrogen permeation behaviors of pre-strained twinning-induced plasticity steel with or without Zn coating using electrochemical permeation technique. In contrast to un-strained and 30% strained samples, permeation current density was measured in the 60% strained sample. Tensile pre-straining at 60% involved microstructural modifications, including a high level of dislocation density and stacking fault with a semi-coherent twin boundary, which might provide a high diffusion path for hydrogen atoms. However, reproducibility of measurements of hydrogen permeation current was low due to non-uniform deformation and localized stress concentration. On the other hand, the permeation current was not measured in pre-strained TWIP steel with Zn coating. Instead, numerous blisters with some cracks were observed on the surface of the coating layer. In locally damaged Zn coating under tensile straining, hydrogen atoms could relatively easily permeate through the coating layer. However, they were trapped at the interface between the coating layer and the substrate, which might delay hydrogen penetration into the steel substrate.

• 펄프종이기술
• /
• 제47권5호
• /
• pp.134-140
• /
• 2015

This study was carried out to evaluate whether EVAc, acryl latex and biobinder could substitute the part of SB latex for pre-coating color formula or not. Different coating colors prepared through the substitution of 30% SB latex with EVAc, acryl latex, and biobinder were applied for pre-coating layer. 100% SB latex is used as a binder for top coating color. The optical properties, gloss, roughness, stiffness, dry- and wet-pick strength were measured. There were no significant differences in the brightness, whiteness, opacity, roughness, ink set-off and gloss of paper coated with 5 different coating colors. However the stiffness, dry- and wet-pick strength were somewhat lower than those of conventional coating color which 100% SB latex was used as a binder. Although the part of SB latex could be substituted with EVAc, acryl latex and biobinder without sacrificing the qualities of coated paper. Further researches on the improvement of stiffness, dry- and wet-pick strength, and the optimization of rheology of coating color in order to improve the qualities of coated paper are strongly recommended.

• 펄프종이기술
• /
• 제46권6호
• /
• pp.63-70
• /
• 2014

Part of SB latex in pre-coating color was substituted with newly developed starch-based bio-binder in order to investigate the effect of starch-based bio-binder in pre-coating color on the properties of coating color and coated paper. Smoothness and gloss of coated paper were decreased with the increase of bio-binder substitution ratio. Brightness and whiteness did not show the significant changes, but stiffness was improved with bio-binder. Ink set-off, dry-pick and wet pick were decreased with the increase of bio-binder substitution ratio. In general, when all SB latex is substituted with bio-binder, ink set-off, dry- and wet-pick were deteriorated. However, it was found that if the bio-binder substitution ratio is controlled below 50%, similar qualities with coated paper manufactured by the use of SB latex binder can be obtained.

• 펄프종이기술
• /
• 제31권4호
• /
• pp.16-22
• /
• 1999

The quantitative analysis of SB latex contents in coating color and coated paper was investigated with FT/Raman spectroscopy. From the measured FT/IR and FT/Ramon spectra, the peaks of coating color were compared with those of each compoents . Calibration curves were obtained by the area of latex peaks and PLS method of QuantIR program. The relation of predicted values in PLS method and actual values in coating mixtures and coating layer was examined. The components of coating layer in coated paper were investigated by EDS , X-mapping and SEM, The contents of latex in z-direction were calculated in the coating layer of unknown coated paper. The latex concentration measurements of Top layer and Pre layer in double coated paper show that each layer has different value. In single coated paper, it is clear that the latex concentration is highest at the surface and decreases with an increase of depth. From those results it is indicated that the latex migrates to the coated surface. The result of this study may be applied to the binder migration study and the quality control in paper mill.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.159.1-159.1
• /
• 2014

We report a simple method for preparing hydrophobic mesoporous silica and its use as a pre-concentrating agent of gas analytes. Hydrophobic mesoporous silica was prepared by coating PDMS (polydimethylsiloxane) thin layer on commercial mesoporous silica with thermal deposition method in a sealed chamber. By using this method, we were able to coat PDMS layer on inner-walls of pores larger than 15 nm. Also, contact angle measured on a surface consisting of PDMS-coated mesoporous silica exceeded $150^{\circ}$, implying that the surface has high water repellency. Pre-concentration ability of PDMS-coated mesoporous silica and baremesoporous silica was tested under dry and humid conditions. Adsorption and molecular desorption of gas analytes was much enhanced by PDMS-coating on mesoporous silica under both dry and humid conditions. Therefore we suggest that PDMS-coated mesoporous silica can be an efficient pre-concentration agent in order to enhance sensitivity of various detectors.

• 한국표면공학회지
• /
• 제45권2호
• /
• pp.70-74
• /
• 2012

In thermal barrier coating (TBC) systems, the life of the coating depends on thermally grown oxide (TGO) layer because most of the failure of TBCs occurs when TGO growth increases. In order to inhibit TGO growth, process was additionally carried out before the heat treatment of the TBC coating layer at $1200^{\circ}C$ in air. In the additional process, heat treatment in vacuum furnace of < $10^{-5}$ torr was conducted for 7 h and 14 h before the heat treatment. The area and length of TGO, as well as the crack length in the TBC were characterized using a scanning electron microscope (SEM). The TGO thickness and crack of specimens pre-heat treated in vacuum furnace were reduced by 45% compare to those heat treated in furnace. Consequently, pre-heat treatment in a vacuum furnace process lead to effective inhibition of growth of the TGO.

• 한국세라믹학회지
• /
• 제44권7호
• /
• pp.368-374
• /
• 2007

CVD-SiC coating has been introduced as a protective layer in TRISO nuclear fuel particle of high temperature gas cooled reactor (HTGR) due to its excellent mechanical stability at high temperature. In order to prevent the failure of the TRISO particles, it is important to evaluate the fracture strength of the SiC coating layer. It is needed to develop a new simple characterization technique to evaluate the mechanical properties of the coating layer as a pre-irradiation step. In present work, direct strength measurement method with the specimen of hem i-spherical shell configuration was suggested. The indentation experiment on a hemisphere shell with a plate indenter was conducted. The fracture strength of the coating layer is related with the critical load for radial cracking of the shell. The finite element analysis was used to drive the semi-empirical equation for the strength measurement. The SiC hemispherical shells were successfully recovered from the section-grinding of TRISO coated particle and successive heat treatment in air. The strength of CVD-SiC coating layer was evaluated from the experimentally measured critical load during the indentation on SiC hemisphere shell. Weibull diagram of fracture strength was also constructed. This study suggested a new strength equation and experimental method to measure the fracture strength of CVD-SiC coating of TRISO coated fuel particles.