• Journal of the Korean Statistical Society
• /
• v.24 no.2
• /
• pp.519-536
• /
• 1995

In the design of experiments for response surface analysis, sometimes it is of interest to estimate the difference of responses at two points. If differences at points close together are involved, the design that reliably estimates the slope of response surface is important. This idea was conceptualized by slope rotatability by Hader & Park (1978) and Park (1987). Until now, second order polynomial models were only studied for slope ratatability. In this paper, we will propose the necessary and sufficient conditions for slope rotatability over all directions for the thired order polynomial models in two, three and four independent variables. Also practical slope rotatable designs over all directions for two independent variables are suggested.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.14 no.4
• /
• pp.94-100
• /
• 2006

The purpose of this case study is to determine the possibility of Numerical Forecasting of sea fog at West Sea in spring time. For practical method of analyzing the data collected from 24th to 26th March 2003, Numerical Weather Prediction model MM5(Mesoscale Model Version 5) and synoptic field study using synoptic chart, upper level chart, and sea surface temperature were employed. The results of synoptic field analysis summarized that sea fog at West sea in spring is intensified by the inflow of the warm flow from west or southwest, low sea surface temperature to increase the temperature difference between air and sea surface, and inversion layer to disturb the disperse. It appears that the possibility of sea fog forecasting by MM5, in view of the result that the MM5 output is similar to the synoptic fields analysis.

• Journal of the Korea Institute of Building Construction
• /
• v.11 no.6
• /
• pp.557-566
• /
• 2011

The surfactants facilitate the formation of foam bubbles under a proper condition and provide stability of foam bubbles by decreasing the surface tension of solutions and increasing the viscosity of foam surface. However, there have been almost no practical data of foam concrete in this regard so far. This study aims to understand the effects of foaming agents such as anionic synthetic surfactant and anionic natural material surfactant on the low density foamed concrete. From the experiment, the vegetable soap of anionic natural material surfactants showed a higher foaming rate, more open pores, slightly lower compressive strength, and a higher permeability coefficient compared to the vegetable soap of anionic synthetic surfactants. It is believed that the natural material surfactants make not only the surface tension of the solution low but also the viscosity of slurry high.

• Structural Engineering and Mechanics
• /
• v.62 no.2
• /
• pp.139-142
• /
• 2017

For the conventional computational methods for structural reliability analysis, the common limitations are long computational time, large number of iteration and low accuracy. Thus, a new novel method for structural reliability analysis has been proposed in this paper based on response surface method incorporated with an improved genetic algorithm. The genetic algorithm is first improved from the conventional genetic algorithm. Then, it is used to produce the response surface and the structural reliability is finally computed using the proposed method. The proposed method can be used to compute structural reliability easily whether the limit state function is explicit or implicit. It has been verified by two practical engineering cases that the algorithm is simple, robust, high accuracy and fast computation.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.151-158
• /
• 2013

There are several kind of surface deformation display methods using the fuzzy model. In this paper, we describe three fuzzy display methods for a surface deformation and perform a comparative analysis between the modified fuzzy display method and some conventional fuzzy display methods. In each method, the analysis will be performed through computer simulation in order to show the performance of each algorithm. The results show that the modified method have improved the realism and can be used better than the conventional methods in practical applications.

• International Journal of CAD/CAM
• /
• v.7 no.1
• /
• pp.103-112
• /
• 2007

This paper presents a practical approach for surface reconstruction from unoriented point clouds. Instead of estimating local surface orientation, we first generate a set of depth images from the input point clouds, and a coarse mesh is then generated based on them by space carving techniques. The resultant mesh is progressively refined by local mesh refinement and optimization according to surface distance measure. A manifold mesh approximating the input points within an given tolerance is finally obtained. Our approach is easy to implement, but has the ability to outputs high quality meshes in different resolutions. We show that the proposed approach is not sensitive to several types of data disfigurement and is able to reconstruct models robustly from variance input data.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.1 no.2
• /
• pp.173-181
• /
• 1989

Until recently there was a lack of reliable performance data for the design and operation of Ondol heating systems. This paper presents a calculation method on heat flux from Ondol floor surface. Total heat flux from floor consists of radiation and convection component. In order to analyse the characteristics of both radiation and convection heat flux, each surface temperature is measured and several temperatures near each wall are measured vertically and horizontally in a practical Ondol heating space. Radiation heat flux is calculated and analysed by Gebhart's Absorption Factor Method with the consideration of instantaneous radiant exchanges. Convection heat output is derived from the vertical temperature profiles near floor. The vertical temperature profiles could be expressed by nonlinear regression equation models and convection coefficients could be estimated by the equations. As a result, radiation, convection and total heat flux are suggested by the expression of difference between floor surface and room air temperature.

• Carbon letters
• /
• v.9 no.1
• /
• pp.47-60
• /
• 2008

Understanding the exact structure and surface characteristics of carbon materials is very important for design, synthesis, and utilization of the best carbon form with particular functions and high performance for practical applications such as selective adsorption adsorbents, energy storage materials, catalysts or catalyst supports, etc. This review paper focuses on carbon surface properties and the interaction between gaseous or liquid substances and carbon surface. Catalytic functions of carbon materials are reviewed including recent progress in synthesis and applications of nano-carbons.

• Journal of the Korean institute of surface engineering
• /
• v.23 no.4
• /
• pp.197-207
• /
• 1990

Atomic layer epitaxy is a relatively new epitaxial pprocess chracterized by the alternate and separate exposure of a susbstrate surface to the reactants contaning the constituent element of a compound semicoductror. The ideal ALE is expected to provide sevral advantageous as petcts for growing complicated heterostrutures such as relativly easy controls of the layer thinkness down to a monolayer and in forming abrupt heterointerfaces though monolayer self-saturatio of the growth. In addition, since ALE is stongly dependent on the surface reaction, the growth can also be controlled by photo-excitation which provides activation can be energies for each step of the reaction paths. The local growth acceleration by photo-excitation can be exploited for growing several device strures on the same wafer, which provides another important practical advantage. The ALE growth of GaAs has advanced to the point the laser opertion has been achieved from AlGs/GaAs quantun well structures where thee active layers were grown by thermal and Ar-laser assisted ALE. The status of the ALE growth of GaAs and other III-V compounds will be reviewed with respect to the growth saturation behavior and the electrical properties of the grown crystals.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.18 no.4
• /
• pp.1-11
• /
• 1981

A flow problem around a ship hull with the nonlinear free surface boundary condition has been considered within the potential flow assumption. The Green's function based on the hull boundary condition is constructed numerically and used to satisfy the free surface boundary condition. This singularity to be distributed ideally on the undulating free surface is put actually, for practical reasons, on the flat water surface with the assumption of linear variation of velocities between the two positions. The surfaces of singularity distribution are approximated by Hess and Smith type quadrilaterals. The radiation condition is only crudely satisfied and this produced one of the major difficulties arising in the present way of attacking the problem.