• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.68-70
• /
• 1996

A fuzzy network using genetic algorithm is investigated in the context of control for finite dimensional nonlinear discrete systems. The proposed FN(Fuzzy Network) constructed to identify various parameter of fuzzy control is used for the nonlinear system control. Each of two FN, presented FN control system is based on a framework of closed loop control. A proposed FNN model trains using the modeling error and the closed loop error. That case study shows that the presented FN model and closed loop control system is very useful in practical sense.

• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.53-56
• /
• 2002

This paper presents neural observer that used to deadbeat load torque observer. Most practical systems are nonlinear, and it is general practice to use linear models to simplify their analysis and design. However, the locally linearized model is invalid for a large signal change. The neural observer is suggested to increase the performance of the load torque observer and main controller The output error and estimeted state is trianed by neural network of neural observer. As a result, the state estimation error is minimised and deadbeat load torque observer make use of corrected esimation state. To reduce of the noise effect of deadbeat load torque observer, the post-filter which is implemented by MA process, is adopted. As a result, the proposed control system becomes a robust and precise system against the load torque. A stability and usefulness, through the verified computer simulation, are shown in this paper.

• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.1018-1025
• /
• 2015

This paper proposes a methodological scheme for the photovoltaic (PV) simulator design. With the advantages of a digital controller system, linear interpolation is proposed for precise fitting with higher computational efficiency. A novel control strategy that directly tackles two different duty cycles is proposed and implemented to achieve a full-range operation including short circuit (SC) and open circuit (OC) conditions. Systematic design procedures for both hardware and algorithm are explained, and a prototype is built. Experimental results confirm an accurate steady state performance under different load conditions, including SC and OC. This low power apparatus can be adopted for PV education and research with a limited budget.

• Journal of Power Electronics
• /
• v.10 no.6
• /
• pp.694-701
• /
• 2010

In this paper an effective direct torque control (DTC) and stator flux control is developed for a quasi six-phase induction motor (QIM) drive with sinusoidally distributed windings. Combining sliding-mode (SM) control and adaptive input-output feedback linearization, a nonlinear controller is designed in the stationary reference frame, which is capable of tracking control of the stator flux and torque independently. The motor controllers are designed in order to track a desired second order linear reference model in spite of motor resistances mismatching. The effectiveness and capability of the proposed method is shown by practical results obtained for a QIM supplied from a voltage source inverter (VSI).

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.420-423
• /
• 1995

The electric arc welding machine with high-frequency inverter is studied in this paper which could make more saving in energy than conventional ones with inherent low efficiency. The inverter circuit has been already adopted to special welding machines such as MIG and TIG for improving operating performances so much. But this adoption has not be applied to conventional ac arc welding machine until now. The proposed technology for higher efficiency is to apply the high frequency inverter, together with noise-cut transformer. Overall output characteristics are investigated in aspect of cost and circuit performance. The proposed system is conducted practical experiments using PWM controller.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.318-320
• /
• 1995

This paper describes the practical implementation of switched reluctance motor drive for a wide range of operation speeds. The angle controller is designed by one-chip microprocessor 8051 for various real time applications. Algorithm to control the speed of SRM and to maintain the speed under the changed load is proposed.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.677-680
• /
• 2003

In this paper, the analysis of practical end-to-end delay in worst case is performed for distributed control system considering the implementation of the system. The control system delay is composed of the delay caused by multi-task scheduling of operating system, the delay caused by network communication, and the delay caused by the asynchronous between them. Through simulation tests based on CAN(Controller Area Network), the proposed end-to-end delay in worst case is validated. Additionally, online clock synchronization algorithm is proposed here for the control system. Through another simulation test, the online algorithm is proved to have better performance than offline one in the view of network bandwidth utilization.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.3 s.96
• /
• pp.9-17
• /
• 1999

This paper presents a method of grinding and polishing automation of precision die after CNC machining. The method employs a robot system equipped with a pneumatic spindle and a special abrasive film pad. The robot program is automatically generated off-line program form a PC and downloaded to robot controller. Position and orientation data for the program is supplied form cutter contact (CC) data of NC machining process. This eliminates separate robot teaching process. This paper aims at practical automation of die finishing process which is very time consuming and suffering from shortage of workpeople. Time loss due to changeover from one product to another is eliminated by PC off-line programming exploiting appropriate NC machining data. Dextrous 6-axis robot with rigid wrist and simple tooling enables the process applicable to larger, rather complex 3 dimensional free surfaces.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.10a
• /
• pp.5-18
• /
• 1993

This paper reports the recent trends in active vibration control in Japan, especially, based on papers selected in the Proceedings of First International Conference on Motion and Vibration Control (1st MOVIC) held at Yokohama, Japan on Sept.7-11, 1992. Firstly, it classifiers vibration control methods and vibration controllers, especially active dynamic absorbers which are widely used in mechanical and civil engineering. Secondly, it covers basic problems in the control of vibration of flexible structures such as formulating a reduced-order model required for designing vibration controller, proper arranging of sensors and actuators, and preventing of spillover instability. Finally, the practical use of control theories such as LQ control theory, $H^{\infty}$ control theory, neural network theory, and other topics are discussed..

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.6 s.123
• /
• pp.539-546
• /
• 2007

Information storage devices using disks have a disk vibration at the frequency which is equivalent to the disk rotational speed. They also have a track vibration due to the disk eccentricity at the same frequency. In near field recording systems, the former affects the air-gap servo and the latter affects the tracking servo. In this paper, we introduce a novel control algorithm based on the internal model principle to both servos. A controller block designed by the principle is connected to the base lead-lag type compensator in parallel in order to cancel the repeatable run-out due to the disk vibration or eccentricity. Simulation and practical application of the algorithm on a near field recording system show good servo performance.