• 대한기계학회논문집B
• /
• 제36권2호
• /
• pp.217-224
• /
• 2012

비도로용 차량의 경우 대부분 디젤엔진을 사용하여 엔진의 특성상 PM과 NOx의 배출이 많은 단점이 있다. 승용 및 상용 디젤 차량의 경우 CRDI 및 후처리 장치를 적용하였고 후처리 장치로 DOC/DPF를 장착함으로써 PM은 약 90% 이상 저감 가능하다. 상반관계인 NOx는 EGR 사용을 통해 1차적으로 NOx 배출량을 감소시키고 LNT, LNC, Urea-SCR 등의 DeNOx 시스템으로 NOx의 배출량을 보다 현저히 저감시켜 배기규제를 만족시키고 있다. 본 연구에서는 tier 4 interim 배기규제를 만족하기 위해 56kW급 오프로드 차량으로 연구를 진행하였다. NOx의 감소를 위해 WGT와 전자 제어방식의 HPL EGR 시스템을 적용하였고 CO와 THC, PM 배출가스를 줄이기 위해 DOC와 DPF를 사용하였다. EGR 시스템을 적용하기 위해 각 조건에 대한 기본 실험을 실시하여 EGR map을 작성하였다. 작성된 map을 NRTC 모드에서 시험하여 map의 적용성을 검증하고 tier 4 interim 배기규제 만족여부를 파악하였다.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.148-159
• /
• 2004

This paper discusses vibration mode of the drivesystem considered the vehicle body's dynamic characteristics to study the influence of the vehicle body's dynamic characteristics on the vibration mode of the engine mount system and the ride quality of a vehicle. The simulation model consists of the engine mount system, the powertrain and the rigid or elastic vehicle body. Variables used in this study are the stiffnesses of an engine mount system and the excitation forces. The Goals of the study are analyzing both the vibration transmitted to the vehicle body including the drivesystem and the influence of the vehicle body's dynamic characteristics on the engine mount system. The mode of drivesystems with a rigid and a elastic vehicle body was compared. From the result of the forced vibration analysis for the drivesystem with a elastic vehicle body, it is shown that the vehicle body's dynamic characteristics influence on the engine mount system reciprocally.

• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.89-95
• /
• 2013

In this work, the evaluation of swirl nozzle injector performance was conducted by investigating effective area ($A_{eff}$), injection mass ($m_{inj}$), injection rate ($Q_{inj}$), and injection delay ($t_{delay}$) under various test conditions. To achieve these, fuel injection analysis system which was composed of fuel supply system, injection system, and control system was installed. At the same time, the swirl nozzle that had 12 orifice hole with $120^{\circ}$ injection angle was used in this work. It was revealed that the difference of injection mass ($m_{inj}$) between base and swirl nozzle injector increased as the injection pressure ($P_{inj}$) and energizing duration ($t_{eng}$) decreased under the same test conditions. The maximum injection rate ($Q_{inj}$) of swirl nozzle injector was higher than base nozzle injector about 2~5%. The injection performance of swirl nozzle was better than base nozzle at low injection pressure ($P_{inj}$) and short energizing duration ($t_{eng}$) conditions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.615-616
• /
• 2006

Many manufacturing companies manage their production-related data for quality management and production management. Nevertheless, production related-data should be closely related to each other Stored data is mainly used to monitor their process and products' error. In this paper, we provide an enterprise-wide production data model for decision support system and product automation. Process data, quality-related data, and test data are integrated to identify the process inter or intra dependency, the yield forecasting, and the trend of process status. In addition, it helps the manufacturing decision support system to decide critical manufacturing problems.

• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.120-127
• /
• 2013

Hybrid electric vehicles have applied electric parts for saving fuel consumption and reducing levels of environmental pollution. Electrification of automobiles is indispensable for entering into global market because of enhanced environment restriction. ISG (Integrated Starter & Generator) system is one of main electric parts and can improve fuel efficiency more than other components by using Idle Stop & Go function and regenerative braking system. However, if ISG motor and inverter work under the continuously high load condition, it will make them the decrease of performance and durability. So the ISG motor and inverter need to properly design the cooling system of them. In this study, we suggested the enhancement points by modifying the thermal design of ISG motor and then confirmed the improvement of the cooling performance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1907-1911
• /
• 2000

In this paper, classical vibration theories are summarized to design engine mount system of passenger vehicles. The vibrational characteristics of powertrain system and its equation of motion are introduced. Based upon the equation, the concept of the center of gravity, the principle inertia axis, the elastic center, and the elastic axis are defined and some new concepts are suggested. The theory of mode decoupling and the relationship between TRA (Torque Roll Axis) and roll mode are also reexamined to support the design concept of engine mount systems.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 춘계학술대회 논문집
• /
• pp.514-519
• /
• 2011

Recently, the interest in technologies for a highly efficient powertrain, i.e. a variable displacement engine or a light weight car body, to improve the fuel efficiency of automobile saving the environment has been increased. However this trend deteriorates NVH performance of a vehicle and the use of a conventional engine mounting system becomes unsatisfactory. In order to solve this dilemma, an active engine mounting system that could isolate or cancel out vibrations occurred at the powertrain was suggested. In this paper, In order to optimize the electromagnetic active engine mount performance, the actuator of the engine mount through FEM analysis and optimal design, noise and elastomer testing of the prototype through the optimal design of actuators for the electromagnetic active engine mount on the impact of the performance improvement is verified.

• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.26-34
• /
• 2011

Hybrid powertrain systems have been developed to improve the fuel efficiency of internal combustion engines. In the case of a parallel hybrid powertrain system, an engine and a motor are directly coupled. Because of the hardware configuration of the parallel hybrid system, friction and the pumping losses of internal combustion engines always exists. Such losses are the primary factors that result in the deterioration of fuel efficiency in the parallel-type hybrid powertrain system. In particular, the engine operates as a power consumption device during the fuel-cut condition. In order to improve the fuel efficiency for the parallel-type hybrid system, cylinder deactivation (CDA) technology was developed. Cylinder deactivation technology can improve fuel efficiency by reducing pumping losses during the fuel-cut driving condition. In a CDA engine, there are two operating modes: a CDA mode and an SI mode according to the vehicle operating condition. However, during the mode change from CDA to SI, a serious fluctuation of the air-fuel ratio can occur without adequate control. In this study, an air-fuel ratio control algorithm during the mode transition from CDA to SI was proposed. The control algorithm was developed based on the mean value CDA engine model. Finally, the performance of the control algorithm was validated by various engine experiments.

• 한국자동차공학회논문집
• /
• 제21권3호
• /
• pp.82-87
• /
• 2013

In this work, the 1L grade integrated metal DOC/DPF filter that can install in engine manifold position was developed to investigate the effect of platinum-coating amount of filter on the improvement of filter activation temperature and reduction of particulate matter (PM). This filter was installed in 2.9L CI engine which meets the EURO-4 emission regulation. Tests for PM reduction efficiency of filter were conducted under ND-13 mode with full-load test condition. It was revealed that the time to reach the activation temperature of metal filter ($280^{\circ}C$) was shorter as the amount of platinum-coating increased. This short activation time can be helpful for the reduction of CO and HC emissions during cold start condition. At the same time, PM reduced as the coating amount increased. The reduction percentage of $DOC_{40}$, $DOC_{20}$, and $DOC_0$ were 96.7% (2.34 mg/kW'h), 95.1% (3.47 mg/kW'h), and 94.5% (3.69 mg/kW'h) compared to previous result (71.4 mg/kW'h), respectively.

• 대한기계학회논문집B
• /
• 제35권2호
• /
• pp.189-196
• /
• 2011

최근, 승용차는 물론 대형차에서도 하이브리드시스템 등의 전기동력방식을 도입하려는 연구개발이 활발하다. 기존의 내연기관을 대체하는 전기구동모터를 이용하여 차량을 구동하는 전기동력방식을 채용하는 것이 한층 더 효율적이며 가속성능, 승차감 등의 면에서도 유리한 점이 많다. 그러나 모터는 엔진과 전혀 다른 특징을 갖기 때문에 동력성능과 에너지효율에 관한 적합한 평가수법을 검토할 필요가 있다. 본 논문에서는 전기구동버스에 대한 구동모터 시스템을 다이나모미터 상에서 운전하여, 노선버스의 운행패턴을 반영한 모의운전을 실시, 가속성능 및 에너지변환효율, 회생효과의 평가방법 등을 고찰하였다. 그 결과 실 주행 패턴운전에 대한 모터일률, 전력량 등의 계측으로부터 모터 변환효율은 90% 전후, 회생전력량은 요구전력량의 40% 이상으로 평가되었다.