• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.418-421
• /
• 2005

The objective of this research work is to investigate the effects of process parameters, such as power of laser, travel speed of laser and material thickness, on kerfwidth and characteristics of the cut surface for the case of cutting of CSP 1N sheet using high power continuous wave Nd:YAG laser. In order to find relationship between the process parameters on the quality of the cut section, such as kerfwidth, surface roughness and the striation formation, several laser cutting experiments are carried out. From the results of experiments, an optimal cutting speed for each cutting condition has been obtained to improve the quality of the cut surface.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.7 s.184
• /
• pp.30-38
• /
• 2006

Laser cutting technology is one of flexible rapid manufacturing technologies with various advantageous including a high cutting speed, manufacturing of parts with a complex shape and others. The quality of the cut part and the optimum cutting conditions are highly dependent on the combination of the process parameters. The objective of this research works is to investigate the influence of process parameters, such as power of laser, cutting speed of laser and material thickness, on the surface roughness and the striation formation of the cut section for the case of cutting of CSP 1N sheet using high power Nd:YAG Laser with a continuous wave (CW). In order to find the relationship between process parameters and the surface roughness and the striation formation of the cut section, several experiments are carried out. Through the investigation of the empirical results, it has been shown that the surface roughness is highly related to the striation formation, including the frequency and angle of the striation, of the cut section. From the results of experiments, an optimum cutting speed for each cutting condition has been obtained to improve both the quality of the cut surface and the cutting efficiency.

• Journal of Radiation Protection and Research
• /
• v.45 no.4
• /
• pp.178-186
• /
• 2020

Background: Reactor pressure vessel (RV) with internals (RVI) are activated structures by neutron irradiation and volume contaminated wastes. Thus, to develop safe and optimized disposal plan for them at a disposal site, it is important to perform exact activation calculation and evaluate the dose rate on the surface of casks which contain cut-off pieces. Materials and Methods: RV and RVI are subjected to neutron activation calculation via Monte Carlo methodology with MCNP6 and ORIGEN-S program-neutron flux, isotopic specific activity, and gamma spectrum calculation on each component of RV and RVI, and dose rate evaluation with MCNP6. Results and Discussion: Through neutron activation analysis, dose rate is evaluated for the casks containing cut-off pieces produced from decommissioned RV and RVI. For RV cut-off ones, the highest value of dose rate on the surface of cask is 6.97 × 10-1 mSv/hr and 2 m from it is 3.03 × 10-2 mSv/hr. For RVI cut-off ones, on the surface of it is 0.166 × 10-1 mSv/hr and 2 m from it is 1.04 × 10-1 mSv/hr. Dose rates for various RV and RVI cut-off pieces distributed lower than the limit except the one of 2 m from the cask surface of RVI. It needs to adjust contents in cask which carries highly radioactive components in order to decrease thickness of cask. Conclusion: Two types of casks are considered in this paper: box type for very-low-level waste (VLLW) as well as low-level waste (LLW) and cylinder type for intermediate-level waste (ILW). The results will contribute to the development of optimal loading plans for RV and RVI cut-off pieces during the decommissioning of nuclear power plant that can be used to prepare radioactive waste disposal plans for the different types of wastes-ILW, LLW, and VLLW.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.4
• /
• pp.273-279
• /
• 1998

In this paper, the proposed charging system consists of step charging mode and time-sharing equalization charging mode. As $\Delta$V=O point is detected, the proposed cut-off method will selectively cut off the only battery to reach the $\Delta$V=O point, preventing serial-connected batteries from undercharging. In the start of each step, the equalization charging mode is performed to reduce the capacity difference among the batteries. Though it is added to simple circuit for selective cut-off, comparing with recently used step-charging method, this system can improve the life cycle of battery and charging efficiency, and be also very effective for preventing the batteries from overcharging and undercharging.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.10A
• /
• pp.776-783
• /
• 2009

Current-cut circuit is an effective method to obtain low power consumption in wireless communication systems as high speed OFDM. For the operation of current-mode FFT LSI with analog signal processing essentially requires current-mode serial-to-parallel/parallel-to-serial converter with multi input and output structure. However, the Hold-mode operation of current-mode serial-to-parallel/parallel-to-serial converter has unnecessary power consumption. We propose a novel current-mode serial-to-parallel/parallel-to-serial converter with current-cut circuit and full chip simulation results agree with experimental data of low power consumption. The proposed current-mode serial-to-parallel/parallel-to-serial converter promise the wide application of the current-mode analog signal processing in the field of low power wireless communication LSI.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.87-92
• /
• 1996

When cutting 2.0cm-thick red oak and hard maple with an air-jet-assisted carbon-dioxide laser of 2kW output power, maximum feed speed at the point of full penetration of the beam decreased with increasing the angle between grain and cutting direction. Feed speed averaged 3.75 and 3.38 meters per minute for red oak and hard maple, respectively. Gray-level of laser-cut surfaces were analyzed by image analysis system. The highest gray level of laser-cut surface was obtained when red oak was cut parallel to grain by laser. Surface profiler was used to scan the sawn and laser-cut surfaces. Center line average roughnesses of laser-cut surfaces were higher than those of sawn surfaces. Scanning electron micrographs showed the cell walls which were melted by laser.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.9-11
• /
• 2000

To increase the device linearities and the breakdown-voltages of FETs, Al$\sub$0.25/ Ga$\sub$0.75/AS / In$\sub$0.25/Ga$\sub$0.75/As / Partially doped channel FET(DCFET) structures are proposed. The metal- insulator -semiconductor (MIS) like structures show the high gate-drain breakdown voltage(-20 V) and high linearities. The devices showed the small ripple of the current cut-off frequency and the power cut-off frequency over the wide bias range.

• Journal of the Korea Society of Computer and Information
• /
• v.8 no.3
• /
• pp.163-169
• /
• 2003

This study was carried out develope a motor power change speed device of motor by used micro- controller. This system was producted a auto-change speed device which switching frequency was 1,000MHz by used a auto- controller. It had a continuous output current such as 5A, 11A, 25A, 35A, 50A. It used a variable voltage from 9V to 18V(Maximum). We designed hardware of and software of micro-controller, we are made up of a auto cut-off function by 3.7V for detected power-loss prevention.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.10-13
• /
• 2008

Fuel cell systems have witnessed remarkable development in recent years as they offer a clean and efficient alternative for power generation. Testing was conducted to determine the safety performance of a residential fuel cell system when subjected to abnormal operation condition, especially for voltage sag and fuel cut. In case of voltage sag to 198V, its arriving time at rated power had shown a slight lag but there wasn't any noticeable change when operating it between rated voltage(220V) and 10% voltage sag(198V). In case of fuel cut, it also showed stable shut-down characteristics. The test results are being used to develop a new safety evaluation for residential fuel cell system.

• Journal of Biosystems Engineering
• /
• v.27 no.4
• /
• pp.301-310
• /
• 2002

With a purpose to manufacture an onion peeler, the root cutting equipment of the onion could be attached to a prototype onion peeler was developed. Before the experiment, the distribution of the dimensions of the Korean native onion were measured. And some types of the blades to cut and remove the root of the onion were designed and such characteristics as feasible revolution, conveying speed, and power requirement were investigated. From the result of the test, the selected one among the various cutters was the wing type blade with the round blade to cut out the root and with the vertical blade to cut a circular line. The optimum operating conditions of the wing type blade were revealed the revolution with no load was at 630 rpm, and the conveying speed was 0.08 m/s. Under these conditions, the maximum torque was 5.25 kg·m and the power requirement was 33 W, respectively.