• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.731-739
• /
• 2014

Aluminum and boron co-doped zinc-oxide(AZOB) powders as transparent conducting oxide(TCO) were prepared by spray pyrolysis at $900^{\circ}C$. The micron-sized AZOB particles were prepared by spray pyrolysis from aqueous precursor solutions for aluminium, boron, and zinc. The micron-sized AZOB particle after the spray pyrloysis underwent post-heat treatment at $700^{\circ}C$ for 2 hours and it was changed fully to nano-sized AZOB particle by ball milling for 24 hours. The size of primary AZOB particle by Debye-Scherrer Equation and surface resistance of AZOB pellet were measured.

• Tribology and Lubricants
• /
• v.31 no.4
• /
• pp.183-188
• /
• 2015

This paper presents the experimental effects of lubricant with nanodiamond particles in sliding friction. In order to improve the performance of lubricants many additives are used, such as MoS₂, cadmium chloride, indium, sulfides, and phosphides. These additives are harmful to human health and to the environment, so alternatives are necessary. One such alternative is nanodiamond powder, which has a large surface area. In order to investigate the effect of nanodiamonds in lubricants under sliding friction, they are dispersed in the lubricant at a variety of concentrations (0 wt%, 0.1 wt%, 0.3 wt%, 0.5 wt%, and 1 wt%) using the matrix synthesis method. Friction and wear tests are performed according to the ASTM G99 method using a pin-on-disc tester at room temperature. The specimens used in this experiment are AISI 52100 ball bearings and AISI 1020 steel discs. During the test, lubricant mixed with nanodiamond is supplied constantly to keep the two bodies separated by a lubricant film. To maintain boundary lubrication, the speed is set to 0.18 m/s and a load of 294 N is applied to the disc through the pin. Results are recorded by using workbench software over the test duration of 10 minutes. Experimental results show that when the concentration of nanodiamond increases, the coefficient of friction decreases. However, above a nanodiamond concentration of 0.5 wt%, both the coefficient of friction and wear volume increase. From this experiment, the optimum concentration of nanodiamond showing a minimum coefficient of friction of 0.09 and minimum wear volume of 0.82 nm² was 0.5 wt%.

• Applied Chemistry for Engineering
• /
• v.23 no.3
• /
• pp.271-278
• /
• 2012

In this work, we have prepared the nanocomposite by the reaction of mica and zinc oxide, and investigated the application of nanocomposite to UV protecting creams. Mica treated with 3-aminopropyltrimethoxysilane (APTMS) reacted with 1,4-phenylenediisothiocyanate (PDC) to give -N=C=S functionalized surface, which was further reacted with zinc oxides coated with APTMS to give mica-zinc oxide nanocomposites. The composites were characterized by EA, EDS, TGA, SEM, zeta potential measurement, powder XRD, and DRS UV/Vis analyses. Finally, we measured transmittances of ultraviolet protection creams manufactured by using mica composite covered with zinc oxides in the range of 280~400 nm. The nanocomposites developed in this work might be applicable as inorganic hybrid materials for UV protecting creams.

• Applied Chemistry for Engineering
• /
• v.24 no.1
• /
• pp.82-86
• /
• 2013

Palladium particles were synthesized with 1-buthyl-3-methylimidazolium trifluoromethanesulfonate ([Bmim][$CF_3SO_3$]) as an effective solvent during the synthesis. The morphology of the particles was affected by the concentration of [Bmim][$CF_3SO_3$]. Furthermore, the palladium on carbon powder was prepared with various [Bmim][$CF_3SO_3$] concentrations and calcinations temperatures as a catalyst for hexafluoropropylene hydrogenation. Catalytic activity was varied by both conditions significantly. Under the identical condition, the catalyst prepared by the same mole ratio of [Bmim][$CF_3SO_3$] and palladium, and calcined at $500^{\circ}C$ was the most active in this reaction.

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.794-801
• /
• 1996

$TiO_2$ fine powders were synthesized via hydrolysis reaction of titanium isopropoxide in isopropanol solvent and the reaction rates were studied by use of UV spectroscopic method. The reactions were controlled to proceed to pseudo-first-order reaction in the presence of excess water in isopropanol solvent. The rate constants which varied with temperature and concentration of water were calculated by Guggenheim method. Reactions using $D_2O$ were also carried out to determine the catalytic character of water. n value of water molecules in transition state and the thermodynamic parameters showed that the reaction proceeded by $S_N2$ mechanism. $TiO_2$ powders synthesized in this reaction were almost spheric forms and had average particle size of $0.3{\mu}m$ diameter.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.210-215
• /
• 2002

This thesis is contents on the crystal grown by the solide phase method at $925^{\circ}C$ with orthorhombic structure that $LiMnO_{2}$ active material synthesised with precurse $Mn_{2}O_{3}$ and $LiOH.H_{2}O$ material to get three voltage level. The porosity analysis of the grown crystal in secondary batteries $LiMnO_{2}$ thin film is $1.323E+02\AA$ of the average pore diameter of powder particles and its structure to be taken the pore diameter was prepared. Adding voltage area to get properties of charge and discharge of which experiment result of $LiMnO_{2}$ thin film area 2.2V~4.3V, current and scan speed were 0.1mAh/g and $0.2mV/cm^{2}$ respectively, and properties of the charge and discharge to be got optimum experiment condition parameter and density rate of Li for analyze that unit discharge capacity with metal properties is 87mAh/g was 96.9[ppm] at 670.784[nm] wavelength, and density rate of Mn analyzed 837[ppm] at 257.610[nm]. It can be estimated the quality of thin film that wrong cell reject from the bottle of electrolyte. The results of SEM and XRD were the same that of original researchers.

• Korean journal of applied entomology
• /
• v.9 no.1
• /
• pp.1-6
• /
• 1970

Cadmium pentachlorophenolxanthate has been synthesized with pentachlorophenol, carbondisulfide sodium hydroxide and cadmium chloride and its fungicidal activity was tested to Pyricularia oryzae and Cochliobolus miyabeanus. The results are summarized as followes; 1) The sample V synthesized by acidifying the crude PCP-xanthate solution at pH 8, then treated with $BaCl_2\;and\;CaC_2$ showed the highest purity, and the yield was $85.1\%$. 2) The same sample of $50\%$ wettable dust formulation inhibited conidial germination of P. oryzae and C. miyabeanus completely at 10 and 20 ppm, respectively. (Fig. 1) 3) The sample of $1.5\%$ dust formulation inhibited mycelial growth of P. oryzae and C. miyabeanus with 96 and $65\%$, respectively. The results were similar to those obtained by Ceresan calcium (Fig. 2) 4) Both dust and wettable powder formulations had no phytotoxcity on rice seedlings.

• Resources Recycling
• /
• v.10 no.6
• /
• pp.29-34
• /
• 2001

Fly ash powders were refined and separated into fine and coarse size by multi-air classification, and each particle was used for synthesizing mullite and zeolite. Mullite was prepared by sintering the mixture of fine fly ash with mean size of 6.5 $\mu$m and $A1_2$$O_3$powder at above $1450^{\circ}C$. Zeolite was synthesized through hydrothermal reaction with coarse fly ash mean size of $56.3\mu$m in 3.5 M NaOH solution at $120^{\circ}C$. The whole range of particle size can be recycled through size classification into fine and coarse fractions, which are used for syntheses of inorganic materials.

• Journal of the Korean Ceramic Society
• /
• v.40 no.1
• /
• pp.31-36
• /
• 2003

In this study, nano-sized NiCuZn-ferrites for the multi-layered chip inductor application were prepared by a coprecipitation method and its electromagnetic properties were analyzed. Also, the property of low temperature sintering were studied with the initial heat treatment of powder.$(Ni_{0.4-x}Cu_xZn_{0.60})_{1+w}(Fe_2O_4)_{1-w}$ (x=0.2, w=0.03) were calcined at $300^{circ}C~750^{circ}C.$ The sintered NiCuZn-ferrites at $900^{\circ}C$ showed good apparent density $4.90g/cm^3,$ and magnetic properties of initial permeability 164 and quality factor 72. As the calcination temperature increase, the grain size of NiCuZn-ferrite increased with irregular grain distribution and its magnetic properties were deteriorated.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.4
• /
• pp.805-810
• /
• 2008

Using metallic Ti powder as raw materials and 1,2-diaminocyclohexane (DACH) as the trial template, two novel reduced titanophosphate open-structures were hydrothermally isolated by varying the $H_3PO_4/H_2O$ ratio to adjust the pH value. TiPO-1 crystallizes in orthorhombic Pbca space group with cell parameters a = 21.956(3) $\AA$, b = 8.6268(11) $\AA$, c = 7.2883(9) $\AA$, V = 1380.5(3) $\AA^3$, Z = 4. TiPO-2 crystallizes in triclinic space group P$\bar{1}$ with parameters a = 5.1620(10) $\AA$, b = 8.815(2) $\AA$, c = 10.655(3) $\AA$, $\alpha$ = $99.45^{\circ}$, $\beta$ = $102.94^{\circ}$, $\gamma$ = $91.06^{\circ}$, V = 465.34 $\AA^3$. TiPO-1 is constructed by infinite -Ti-O-Ti-O- linkage that is capped by $PO_4$ groups to form a chain structure with protonated DACH molecules occupying the interchain spaces. TiPO-2 represents a rare 3-D reduced titanophosphate with 12-MR channels. The structure of TiPO-2 is a neutral framework with water molecules located in the channels.