• 한국재료학회지
• /
• 제15권12호
• /
• pp.765-772
• /
• 2005

PAS(Plasma Activated Sintering) process was tried to apply for the fabrication of BMG(Bulk Metallic Glasses) of $Ni_{57}Zr_{20}Ti_{18}Si_5}\;and\;Ni_{57}Zr_{20}Ti_{18}Si_3Sn_2$ from the as-atomized amorphous powder. Compressive strength for the BMG(bulk Metallic Glasses) of $Ni_{57}Zr_{20}Ti_{18}Si_5$ were lower than those of BMG rods produced by warm extrusion ,or copper mold casting method. Microstructural examination by optical microcope, SEM ana EDS showed that oxidation had occurred during PASintering. In order to prevent the powder from the oxidation during PASintering, Ni coating for $Ni_{57}Zr_{20}Ti_{18}Si_5$ amorphous powder by electroless-plating method was performed. Microstructural examination for Ni coated layers after PASintering indicated that the Ni coating had been so effective to prevent powder from oxidation during PASintering. Sintering behaviors of $Ni_{57}Zr_{20}Ti_{18}Si_3Sn_2$ represent the same as those of $Ni_{57}Zr_{20}Ti_{18}Si_5$.

• 한국재료학회지
• /
• 제16권6호
• /
• pp.355-359
• /
• 2006

Fine silica powders were synthesized via w/o emulsion method using sodium silicate, ammonium sulfate, Triton N-57, and cyclohexane as silica source, precipitating agent, surfactant, and oil phase, respectively. The powders were prepared under a conventional process and an ultrasonic process using the same reactants at room temperature for 1 hr varying the concentration of $Na_2SiO_3$ solution and the mol ratio of $H_2O$/surfactant, respectively. The particle size of the silica powder was reduced with decreasing the concentration of sodium silicate solution and with increasing the mol ratio of $H_2O$/surfactant under with and without ultrasounds. The size of powder with ultrasounds was smaller than that without ultrasounds, which indicates that the application of ultrasound in the synthesis of silica powder is an efficient way to reduce particle size.

• The Korean Journal of Ceramics
• /
• 제5권2호
• /
• pp.125-130
• /
• 1999

After $SnO_2$ fine powder by precipitation method, Ca as crystallization inhibitor and Pd as catalyst were added to $SnO_2$ raw material by various methods. Thick film device was fabricated on the alumina substrate by mixing ethylene glycol and such mixed powders. The sensing characteristics of the device for methane gas were investigated. The most excellent gas sensing property was shown by the thick film device fabricated by Method 3 in which Ca and Pd doped $SnO_2$ powder is prepared by mixing $SnO_2$ powder, 0.1 wt% Ca acetate and 1 wt% $PdCl_2$ in deionized water and by calcining the mixture, after $Sn(OH)_4$ is dried at $110^{\circ}C$ for 36h. The sensitivity of the sensor fabricated with $SnO_2$-0.1 wt%Ca acetate-1wt%$PdCl_2$ powder heat-treated at $700^{\circ}C$ for 1h was about 86% for 5,000 ppm methane in air at $350^{\circ}C$ of the operating temperature. Response time and recovery were also excellent.

• 한국분말재료학회지
• /
• 제10권4호
• /
• pp.235-240
• /
• 2003

The $Al/Al_2O_3$ composites fabricated by powder in sheath rolling method were cold-rolled by 50% reduction and annealed for 1.8 ks at various temperatures ranging from 200 to 50$0^{\circ}C$, for improvement of the mechanical properties. The mechanical properties and texture of the composites after rolling and annealing were investigated. The tensile strength of the composites increased significantly due to work hardening after cold rolling, however it decreased due to restoration after annealing. The strength of the composites was improved by thermo mechanical treatment. On the other hand, the texture evolution with annealing temperatures wa,i different between the unreinforced material and the composites. The unreinforced material showed a deformation (rolling) texture of which main component is ｛112｝<111> at annealing temperatures up to 30$0^{\circ}C$. However, the composites have already exhibited a recrystallization texture of which main component is ｛001｝<100> after annealing at 20$0^{\circ}C$. This proves that the critical temperature for recrystailization is lower in the composites than in the unreinforced ones.

• 한국재료학회지
• /
• 제9권6호
• /
• pp.615-621
• /
• 1999

The new process in order to fabricate of Ni catalyst with high activity by the mechanochemical(MC) method which was combined the mechanical alloying(MA) and the chemical treatment process. The microstructure and characterization of mechanically alloyed Ni-5-wt% Al powder and Ni catalyst gained by alkali leaching were investigated byt he various analysis such as XRD, SEM-EDS, HRTEM and laser particle analyzer. The steady state powder with 1~2$\mu\textrm{m}$ mean particle size was obtained after 30hr milling with the PCA of 2 wt% stearic acid under the condition of grinding stainless steel ball to powder ratio of 60:1 and rotating speed fo 300rpm. According to result of HRTEM diffraction pattern, MA powder of the steady state was nanocrystalline $Al_3$$Ni_2$ intermetallic compound. Ni catalyst was obtained after KOH leaching of the steady state powder was about 20nm nanocrystalline which contained about 8 wt % Al.

• Corrosion Science and Technology
• /
• 제23권1호
• /
• pp.54-63
• /
• 2024

This work investigated the influence of concentration and applied potential on the characteristics of zinc powder (purity, apparent density, morphology, particle size distribution, and particle zeta potential) produced by the electrochemical process from waste brass. High-purity zinc powder is obtained using selective leaching of industrial brass waste in acidic, neutral, and alkaline solutions. The free immersion method with and without voltage using linear polarization technique is used. In the electrochemical process, hydrochloric acid HCl in three different concentrations (0.1, 0.2, and 0.3) M is used. The time and the distance between the electrodes are set to be 30 min and 3 cm, respectively. It has been found that the percentage purity is 98%, 96%, and 94% for the acidic, neutral, and alkaline solutions, respectively. In addition, the morphology of zinc powder analyzed by SEM was dendritic and mossy. It has been recorded that the purity of zinc increases with the increase of the concentration and applied potential. The highest value of purity for zinc powder was %98.58 in 1000 mV and 0.3M concentration for graphite cathode.

• 한국표면공학회지
• /
• 제42권5호
• /
• pp.227-231
• /
• 2009

The niobium capacitor showed somewhat more unstable characteristics than the commercial tantalum capacitors, but is nonetheless considered applicable as a future substitute for tantalum capacitors. In this study, niobium powder was fabricated by metallothermic reduction process using $K_2NbF_7$ as the raw materials, KCl and KF as the diluents and Na as the reducing agent. The niobium particle size greatly decreased from 0.7um to 0.2 um as the amount of diluent increased. However if a higher surface area of powder is required, more diluents need to be used in the said method in order to produce niobium powder. The niobium powder morphology and particle size are very sensitive to a amount of sodium excess. The particle size of niobium powder increased with a increasing amount of sodium excess. When more diluent and sodium are used, the niobium powder will be contaminated with more impurities such as Fe, Cr, Ni so on.

• 한국세라믹학회지
• /
• 제40권7호
• /
• pp.696-701
• /
• 2003

교반형 볼 밀에서 실리카 분말의 열처리에 따른 분쇄효율을 분쇄에 따른 에너지 소비량을 측정함으로써 조사하였다. 열처리를 행한 것과 행하지 않은 시료를 비교해 보면, 600~90$0^{\circ}C$에서 열처리 후 실온에서 냉각된 시료를 건식 분쇄하였을 경우 약 40~50% 정도, 열처리 후 물속에서 급속 냉각한 경우 약 52～62% 정도의 에너지의 감소 효과가 있었다. 또한 열처리한 실리카 분말을 습식 분쇄를 할 경우 건식 분쇄에 비하여 약 40% 정도의 분쇄에너지가 적게 소모되고 있음을 알 수 있었다. 또한 실리카 분말을 열처리 한 후, 급속 냉각할 경우 발생하는 열충격은 입도에 대한 영향을 거의 받지 않으며 분쇄효과를 향상시킴을 알 수 있었다.

• 한국세라믹학회지
• /
• 제39권7호
• /
• pp.687-692
• /
• 2002

단일상 페로브스카이트 PMN-PT 분말 합성 과정에서 전구체 분말의 표면을 소량의 magnesia 졸로 코팅하여 구형의 분말을 제조하고자 시도하였다. 질량 감소가 더 이상 발생하지 않도록 정량의 혼합 분말을 55$0^{\circ}C$/lh 열처리하여 얻은 전구체 분말을 0.3-1.0wt% MgO에 해당하는 magnesia졸과 혼합한 후 80$0^{\circ}C$/lh 하소하여 페로브스카이트 단일상 PMN-PT 분말을 얻었다. MgO(0.3)일 경우는 <0.3$\mu\textrm{m}$와~2$\mu\textrm{m}$의 두 종류 크기의 분말로 나타나나, MgO(0.6)과 MgO(1.0)의 경우는 0.5-0.8$\mu\textrm{m}$의 구형 분말을 응집없이 얻을 수 있었다.

• 한국재료학회지
• /
• 제11권9호
• /
• pp.763-768
• /
• 2001

Molybdenum-based thermal spray powder is widely used for coating the moving parts of the internal combustion engines due to its excellent wear resistance. A composite powder of the $Mo_{40}(Al_{1-x}Si_x)_{60}$ system was synthesized using the SHS method. The synthesized bulk was pulverized and specially treated to produce thermal spray powder. It was found that the synthesis reaction consisted of two-steps: the formation of $Al_8/Mo_3$ and the formation of Mo(Al,Si)$_2$. Both the temperature and the rate of the SHS reaction linearly increased with the increase of the value of x in $Mo_{40}(Al_{1-x}Si_x)_{60}$, The temperature and the rate of the reaction were also affected by the compacting density of the specimens, exhibiting the maximum valves at 62% and 60%, respectively. Since spherical shape is advantageous to the thermal spraying process, shape-control of the powder was attempted with PVA as a binding additive, resulting in the successful production of almost perfectly spherical powder of 80 $\mu\textrm{m}$ Ø$(d_{50})$ mean particle size.