• Journal of Powder Materials
• /
• v.2 no.2
• /
• pp.135-141
• /
• 1995

As the first step of study on fabrication of ceramic powders from phytoliths in rice, especially in rice husks, pulverization method of rice husks and the properties of milled rice husks were investigated. Impact methods, such as ball milling, were not meaningful for pulverizing elastic and thin fabric structure of rice husks. The most effective one was cutting method. In the present work, a rotating knife cutting method was applied to pulverizing rice husks. A 40-mesh screen was inserted under the rotating knives. The most portion of the milled powder was found in -50/+100 mesh section. Morphology of the milled rice husks revealed that the husks larger than 70 mesh were flake-like shape, at -70/+100 mesh section relatively equi-axed shape, at -170/+325 mesh section rod-like shape, and below 325 mesh section dust-like shape. Tap density of raw rice husks was about 0.1 $g/cm^3$, while those of milled rice husks were over $0.4 g/cm^3$. This meant that, for a given volume of reactor, raw material charge can be increased more that 4 times when using milled rice husks than unmilled one. True densities of unmilled and milled rice husks were higher than $1.4 g/cm^3$, and increased with decreasing milled sizes.

• Korean Journal of Materials Research
• /
• v.16 no.6
• /
• pp.341-345
• /
• 2006

[ $Ni_2Si$ ] mixed powders were mechanically alloyed by a ball mill and then processed by hot isostatic pressing (HIP) and spark plasma sintering (SPS). In the powder that was mechanically alloyed for 15minutes(MA 15 min), only Ni and Si were observed but in the powder that was mechanically alloyed for 30minutes(MA 30 min), $Ni_2Si$, Ni and Si were mixed together. Some of the MA 15 min powder and MA 30 min powder were processed by HIP under pressure of 150MPa at the temperature of $1000^{\circ}C$ for two hours and some of them were processed by SPS under pressure of 60 MPa at the temperature of $1000^{\circ}C$ for 60 seconds. Both methods completely compounded the powders to $Ni_2Si$. The maximum density of sintered lumps by HIP method was 99.5% and the maximum density of the sintered lump by SPS method was 99.3%. with the hardness of HRc 66 with the hardness of HRc 63. Therefore, the SPS method that can sinter in short time at low cost is considered to be more economical that the HIP method that requires complicated sintering conditions and high cost and the sintering can produce target materials in desired sizes and shapes to be used for thin film.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.589-590
• /
• 2006

Based on the comparison of structures and properties of the HS6-5-2 high speed steels made with the powder injection moulding method, pressureless forming, compacting and sintering, and commercial steels made with the ASEA-STORA method, fine carbides spread evenly in the steel matrix were found in the structure of all tested high-speed steels in the sintered state. The steels made with the pressureless forming method are characteristic of the lowest sintering temperature and the highest density, resulting from the high carbon concentration coming from the binding agent degradation.

• The Korean Journal of Food And Nutrition
• /
• v.29 no.4
• /
• pp.513-520
• /
• 2016

Recently, the incidence of cardiovascular diseases including high blood pressure and heart disease has increased with increased meat consumption in Korea. This study was performed to determine the optimal mixing ratio among ratios of 0, 1:0, 0:1, 1:1, 2:1, and 1:2 of mulberry leaf powder to mulberry fruit powder based on the anti-inflammatory effects. Then, the quality characteristics of the sauce for meat prepared with different mixing ratios (0, 1:1, 1:2, 1:3, 1:4, and 1:5) of mulberry leaf powder to mulberry fruit powder were assessed. The inhibitory effects of ML2MF1 (2:1 ratio of mulberry leaf powder to mulberry fruit powder) on NO and TNF-${\alpha}$ production were superior to those of other mixing ratios. With respect to color values of the sauce for meat prepared with different mixing ratio of mulberry leaf powder to mulberry fruit powder, as the mulberry fruit powder mixing ratios was increased, redness was increased but lightness and yellowness were decreased. The sensory evaluation of ML1MF5S (1:5 ratio of mulberry leaf powder to mulberry fruit powder) sauce for meat showed the highest score with respect to color, smell, taste, harmony with meat and the overall preference. In conclusion, as the mulberry leaf powder mixing ratio was increased, the anti-inflammatory activities were increased. But sensory evaluation scores were increased as the mulberry fruit powder mixing ratio was increased. Therefore, by performing further study, the method to increase mulberry leaf powder in the mixing ratio for improving the sensory evaluation should be provided.

• Journal of Powder Materials
• /
• v.12 no.3
• /
• pp.186-191
• /
• 2005

A formation of aluminum hydroxide by hydrolysis of nano and micro aluminum powder has been studied. The nano aluminum powder of 80 to 100 nm in diameter was fabricated by a pulsed wire evaporation (PWE) method. The micro powder was commercial product with more than $10\;{\mu}m$ in diameter. The hydroxide type and morphology depending on size of the aluminum powder were examined by several analyses such as XRD, TEM, and BET. The hydrolysis procedure of micro aluminum powder was different from that of nano aluminum powder. The nano aluminum powder after immersing in the water was transformed rapidly to a nano fibrous boehmite, accompanying with a remarkable temperature increase, and then further transformed slowly to a stable bayerite. However, the micro powder was changed to the stable bayerite slowly and directly. The formation of fibrous aluminum hydroxide from nano aluminum powder might be due to the fine cracks which were formed by hydrogen gas pressure on the surface hydroxide layer during hydrolysis. The nano powder with large specific surface area and small size reacted more actively and faster than the micro powder, and transformed to meta-stable hydroxide in relatively short reaction time. Therefore, the formation of fibrous boehmite is special characteristic of hydrolysis of nano aluminum powder.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.120-125
• /
• 2002

AC powder EL devices were fabricated by screen printing method with the dielectric materials in insulating layer and the electrical resistivity of rear electrode. Brightness and current density were measured at voltage range of 50∼300 $V_{rms}$ to estimate optoelectrical properties of AC powder EL devices, respectively. Frequency generator was used as system producing frequency and voltage of a sine wave. Brightness and current density were measured by luminometer and multimeter. Also, dielectric constant for dielectric layer was measured by impedance analyser after preparing thick film. Dielectric constant was improved with amount of $TiO_2$ to $BaTiO_3$ powder. By applying such a process to dielectric layer of low cost AC powder EL device, brightness was improved to 50 cd/$m^2$ at similar current density. Dielectric constant $BaTiO_3$ powder by solution combustion process is better than commercial $BaTiO_3$ powder. By applying to that of low power consumption AC powder EL device, brightness was improved to 85 cd/$m^2$. Brightness of AC powder EL device was relatively decreased by control of electrical resistivity of rear electrode, current density was also decreased.

• The International Journal of Costume Culture
• /
• v.8 no.2
• /
• pp.124-131
• /
• 2005

This study focused on the change of skin temperature by the emissivity and emission power of far-infrared for conformant far infrared effect to naked eyes. The study method is to manufacture the bra pad by each concentration on far-infrared materials of illite powder $(K,H_3O)AI_2(Si,Al)_4O_{10}(H_2O,OH)_2)$, liquid alumina ($Al_2O_3$), the extracted liquid from 29 kind of medical plants, then, measured change of skin temperature. Result are as follows. Far-infrared were emitted each $90.2\%,\;90.1\%,\;89.7\%$ from the illite powder, liquid alumina, extracted liquid from medical plants. When the testee weared the bra pad, the temperature of coated bra pad was $0.5^{\circ}C$ higher than the non finished bra pad. Washing fastness on far-infrared finishing was better dope addition method than coating method.

• Journal of Food Hygiene and Safety
• /
• v.10 no.1
• /
• pp.41-43
• /
• 1995

Dry rehydratable film (Petrifilm) method was compared with the standard pate count (SPC) method for estimation of total bacteria in ginseng products. Ginseng products (7 sample) was analyzed for total count by the SPC, and Petrifilm methods, respectively. In the case of ginseng tea, ginseng extract, ginseng extract pill, ginseng powder capsule, and ginseng extract tea, they showed non-significant values at the 1% level. However, the values of ginseng powder and tablet showed significant at the 1% level. These results generally indicate the suitability of the dry rehydratable film methods as alternatives to the SPC method for estimating of total bacteria in ginseng product samples except to ginseng powder and ginseng tablet.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1989.06a
• /
• pp.77-80
• /
• 1989

The aim of the study is to develope the processing technique of PZT-Polymer piezoelectric composite materials for ultrasonic transducer application such as biomedical probe and hydrophone. Piezoelectric composite of PZT and polymer with 1-3 connectivity patterns have been fabricated by dicing-filling method and extrusion forming method. In this study processing forming method. In the study processing steps by extrusion forming method in the preperation of PZT/polymer piezoelectric composites are described. The PZT powder used in the study is commercial powder which is prepared by mixing PbO, TiO$_2$ and ZrO$_2$. The binder, water and plasticizer are mixed with the PZT powder to form a slip. It is necessary to adjust the viescosity of slip according on the PZT rod diameters to be extruded. The electromechanical properties of the piezoelectric composites are characterized in terms of the thickness resonance mode. The pulse response characteristics by the ultrasonic transducer analyzer and osciloscope are evaluated.

• Transactions of Materials Processing
• /
• v.13 no.1
• /
• pp.78-83
• /
• 2004

High-temperature superconduction materials(Bi2223) possess electrical/electronic and magnetic properties. Because high-temperature superconduction materials is a ceramic powder, that cannot be produced singlehandedly. So Ag sheathed Bi-2223 wire was produced by drawing process using powder-in-tube(PIT) method. This superconductor has many difficulties to produce. The main difficulty is that the mechanical properties of the ceramic powder are very different from those of the Ag sheath. And by these properties, Bi2223 high-temperature superconductor, which has a single filament drawing process and multi-filament drawing process, has a defect like sausaging and bursting at a center. This study analyzed multi-filament drawing process by FEM, and a defect generated during multi-filament drawing was studied by FEH. Specially, in order to prevent a bursting at a center, this study presented a method that inserts a pure Ag at a center of multi-filament wire