• 한국분말재료학회지
• /
• 제10권5호
• /
• pp.349-352
• /
• 2003

This study examined the correlation of various operational factors including reaction temperature and the quantity of reductant and diluent with the characteristics of powder using $K_2$ TaF$_{7}$ as feed materials, Na as a reductant and KCl/KF as a diluent. Also to control the particle size and shape, external supply system developed, it can provide a feed material and a reductant at a fixed quantity and evaluated the characteristics of tantalum powder. When the external supply system was applied instead of the batch type process that charges feed material, reductant and diluent at the same time, it was possible to induce regular reduction reaction between feed material and reductant, which increased the recovery rate and reduced the mixture of impurities. In particular, the application of the external supply system enabled the control of reaction temperature and reaction speed according to the feeding rate of feed material during reduced reaction, and resultantly it enabled the manufacturing of granular-shaped powder with a regular granularity of 2∼3 ${\mu}{\textrm}{m}$ and purity of 99.5%.

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.154-165
• /
• 1997

Abrasive wear characteristics of high Cr white cast iron-based hardfacing were investigated using the rubber wheel abrasion wear test method according with the ASTM G65-85. Mild steel was also tested for comparison with high Cr cast iron hardfacing. Wear experiments, where the applied force, wheel revolution rate and abrasive powder feed rate were selected as test valuables, were planned and analyzed by response surface method to evaluate wear statistically and quantitatively. Weight loss of high Cr cast iron hardfacing was mostly affected by the applied force and wheel revolution rate, and little by the powder feed rate. Weight loss of mild steel was greatly affected by the wheel revolution rate and powder feed rate, and slowly and steadily increased with the applied force. Abrasive wear mechanism of high Cr cast iron and mild steel was discussed in the light of the wear test results.

• Journal of Welding and Joining
• /
• 제25권4호
• /
• pp.49-57
• /
• 2007

The optimization of the cladding parameters was studied to maximize the deposition efficiency in the laser cladding using a low power pulsed Nd:YAG laser. STS304 stainless steel plate and Co alloy powder were used as a substrate and powder for cladding, respectively. The six cladding parameters were selected through preliminary experiments and their effects on the deposition efficiency were analyzed statistically. Experiments were designed and carried out using the Taguchi experimental method using a L18 orthogonal array. It was found from the results of analysis of variance(ANOVA) that the powder feed position and powder feed angle had the most significant effects on the deposition efficiency, but the powder feed rate and laser focal position had nearly no effects. The deposition efficiency could be maximized at 0mm of the powder feed position and 50o of the powder feed angle in the experimental range. From this experimental analysis, a new laser cladding head with 20o of the powder feed angle was designed and manufactured. With a new laser cladding head, the highest deposition efficiency of 12.2% could be obtained.

• Journal of Welding and Joining
• /
• 제15권1호
• /
• pp.116-124
• /
• 1997

A scope of this study is to establish the optimum plasma spray conditions for fine ($5\mu\textrm{m}$) $Al_2O_3$ powder. However, the flowability of the $Al_2O_3$ powder is not so good because of irregular particle shape and fine particle size. Therefore, powder feeding system was modified by 1) change of powder feeding line material from polymer to copper 2) shorten the powder feeding tube length 3) heating the powder feeding system to $80^{\circ}C$4) vibrating the powder feeding line continuously, in order to feed the fine powder homogeneously. The homogeneous powder feeding conditions were obtained with the modified powder feeding system by controlling the powder carrier gas flow and the powder flow rate indicator. The best plasma spraying conditions for the fine $Al_2O_3$ powder were found out as 40kw gun power, 80 g/min. powder feed rate and 50 mm working distance after characterizing the microstructure, hardness and wear loss of the $Al_2O_3$ coating layer.

• Journal of Welding and Joining
• /
• 제15권1호
• /
• pp.125-134
• /
• 1997

This study was conducted by L9 orthogonal array to obtain optimum spray parameters for This study was conducted by L9 orthogonal array to obtain optimum spray parameters for $Cr_3C_2 - 7wt%$(80wt%Ni-20wt%Cr) coating powder. The factors were hydrogen flow rate, oxygen flow rate, gun-to-work distance, powder feed rate. And evaluation methods for the coating were surface roughness, oxygen concentration, micro-hardness, pore size and distribution, low angle ($30^{\circ}$) erosion rate, and microstructure of coating. The optimum HVOF spray conditions were proved as follows : hydroen flow rate ; 681 SLPM, oxygen flow rate ; 215 SLPM $H^2/O^2 ratio= 3.16), gun-to-work distance ; 22cm, powder feed rate; 25g/min. The hardness (Hv300) was 1147 and the erosion rate ($30^{\circ}$degree) was $3.16\times10^{-4}$g/g. It is believed that the optimized spray conditions can be improved the wear-resistance and anti-erosion characteristics of the coating.

• 소성∙가공
• /
• 제24권4호
• /
• pp.272-279
• /
• 2015

The characteristics of the laser metal deposition parameters were studied to enhance the deposition efficiency using a diode pumped disk laser. STD61 hot tool steel plate and Fe based AISI M2 alloy were used as a substrate and powder for the laser metal deposition, respectively. Among the laser metal deposition parameters the laser power, track pitch and powder feed rate were used to estimate the deposition efficiency. From the experimental results, the deposition efficiency was shown to be excellent when 1.8kW laser power 500um track pitch and 10g/min of the powder feed rate were used. For this optimal condition the average hardness of the deposition track was approximately 830HV, and this value is 30~50% better than the hardness of the commercially produced tool steel after heat treatment.

• 한국레이저가공학회지
• /
• 제2권2호
• /
• pp.34-41
• /
• 1999

A RS840 $CO_2$laser and a powder auto-feeding apparatus have been used to deposit single tracks of Ni-base superalloy on low carbon steel. In this paper, the effects of laser cladding parameters on clad geometry, dilution and microhardness are studied. As a results, the w/h ratio of the clad layer increases with decreasing powder feed rate and increasing laser scan speed. Increase of powder density and decrease of specific energy have little effect on dilution. It was found that the clad layer of the highest hardness has a structure in which fine and leaf like phases are dispersed in ${\gamma}$Ni matrix.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.144-145
• /
• 2004

Submerged arc welding technique using metal powder as supplementary filler metal has been studied. Forward feeding was used, and the deposit rate was increased by 50%. Good bead appearance, soundness and mechanical properties were obtained with feed rate of 120g/min..

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.109-115
• /
• 1997

Laser cladding is a technique for modification of metal surface. In this laser cladding experiment a metal powder feeding system was developed for more efficient laser cladding. This system can reduce processing time and be used simpler than the conventional method. The feeding of metal powder has given a rise to the process for sequential buildup of bulk rapidly solidified materials in the form of fine powder stream to the laser cladding process. The parameters of laser cladding have been investigated using this experimental equipment. Bronze on aluminum alloy and copper on aluminum alloy were experimented by using defocused beam, powder feeding system, and gas shielding. Good cladding was achieved in the range of beam travel speed of 2.25m/min. In the case of copper/aluminum and bronze/aluminum substrate, the absorption of laser beam was too high to produce low diluted clad. In the case of copper/1050 aluminum, the optimal laser cladding condition was of laser power of 2.8kW, powder feed rate of 0.31g/s and beam travel speed of 2.25m/min. In the case of bronze/aluminum the optimal condition is of laser power of 2.5kW, powder feed rate of 0.31g/s, and beam travel speed of 2.36m/min.

• 한국수산과학회지
• /
• 제45권6호
• /
• pp.679-685
• /
• 2012

A study was carried out to observe the effects of feed types on the growth, feed preference, and enteric feed transition rate of juvenile starry flounder, Platichthys stellatus for 45 days. Fifty fish (avg. 135 g) were stocked each in replication, and fed a commercial extruded pellet diet (EP, 45% protein) and a moist pellet diet (MP, 65% raw mackerel+35% feed powder in wet basis), respectively. The MP presented the higher performance than that of the EP on the feed efficiency ($68.3{\pm}0.9%$ for EP and $92.3{\pm}4.3%$ for MP) and the specific growth rate ($1.07{\pm}0.07$ for the EP and $1.20{\pm}0.05%$ for the MP). In contrast, the EP showed the higher feed preference in terms of the daily feed intake ($1.57{\pm}0.08%$ for the EP and $1.30{\pm}0.01$ for the MP) and the ad libitum feeding rate after a fast of 72 hours (1.73% for the EP and 1.35% for the MP). The feed transition rate through intestinal canals decreased exponentially in both the EP and the MP, showing the faster transition rate with the EP. In the result, starry flounder appeared to have the better feed preference to the EP, but have the higher feed efficiency and growth performance to the MP.