• Journal of Powder Materials
• /
• v.24 no.5
• /
• pp.389-394
• /
• 2017

Ni wires with a diameter and length of 0.4 and 100 mm, respectively, and a purity of 99.9% are electrically exploded at 25 cycles per minute. The Ni nanopowders are successfully synthesized by a pulsed wire evaporation (PWE) method, in which Ar gas is used as the ambient gas. The characterization of the nanopowders is carried out using X-ray diffraction (XRD) and a high-resolution transmission electronmicroscope (HRTEM). The Ni nanopowders are classified for a multilayer ceramic condenser (MLCC) application using a type two Air-Centrifugal classifier (model: CNI, MP-250). The characterization of the classified Ni nanopowders are carried out using a scanning electron microscope (SEM) and particle size analysis (PSA) to observe the distribution and minimum classification point (minimum cutting point) of the nanopowders.

• Tribology and Lubricants
• /
• v.39 no.6
• /
• pp.244-249
• /
• 2023

This paper presents a comprehensive analysis of the impact of surface roughness on the friction and wear properties of SUS 321, an austenitic stainless steel variant produced using the laser powder bed fusion (LPBF) technique, which is a prevalent additive manufacturing method. After the LPBF fabrication, the specimens go a heat treatment process aimed at alleviating residual stress. Subsequently, they are polished extensively to achieve a refined and smooth surface. To deliberately introduce controlled variations in surface roughness, an etching process is employed. This multi-step method encompassed primary etching in a 3M hydrochloric acid solution, followed by secondary etching in a 35 wt% ferric chloride solution, with varying durations applied to different specimens. A comprehensive evaluation of the surface characteristics ensued, employing precise techniques such as surface roughness measurements and meticulous assessments of water droplet contact angles. Following the surface treatment procedures, a series of friction tests are performed to explore the tribological behavior of the etched specimens. This in-depth investigation reached its peak by revealing valuable insights. It clarified a strong correlation between intentionally altered surface roughness, achieved through etching processes, and the resulting tribological performance of LPBF-fabricated SUS 321 stainless steel. This significantly advances our grasp of material behavior in tribological applications.

• Journal of Conservation Science
• /
• v.36 no.2
• /
• pp.82-92
• /
• 2020

Modern artworks are constructed using a variety of materials and techniques. Sculptures, which predominantly consist of metals, usually have different shapes and consist of different material mixtures. The structural and material properties of these sculptures are often controlled by conservation treatment methods. However, the application of existing treatment methods is challenging at times, indicating that more diverse treatment materials and techniques are necessary. Therefore, in this study, a treatment method that employs volatile corrosion inhibitor(VCI) powder, rather than an anti-corrosion solution, for the conservation and management of metal artworks was used. VCI powder and VCI films containing VCI powder were used, and the results obtained confirmed that both of them showed anti-corrosion effect. Only a slight change in the chromaticity of metal samples was observed, and compared to the untreated samples, the application of the VCI powder resulted in a decrease in the rate of corrosion by half. Moreover, VCI film tests revealed that comparing to the untreated or polyethylene film-treated samples, VCI film treatment resulted in a decrease in the occurrence of corrosion compounds. The contact angle, surface energy, and surface electrical resistance were measured, and the evaluation of these surface properties established the anti-corrosion effect of VCI. Additionally, direct application of VCI and VCI films on actual sculptures further confirmed the anti-corrosion effect of VCI.

• Korean Journal of Materials Research
• /
• v.24 no.9
• /
• pp.495-501
• /
• 2014

Despite having many attractive properties, $ZrO_2$ ceramic has a low fracture toughness which limits its wide application. One of the most obvious tactics to improve its mechanical properties has been to add a reinforcing agent to formulate a nanostructured composite material. Nanopowders of $ZrO_2$ and Cr were synthesized from $CrO_3$ and Zr powder by high energy ball milling for 10 h. Dense nanocrystalline $2/3Cr-ZrO_2$ composite was consolidated by a high-frequency induction heated sintering method within 5 min at $600^{\circ}C$ from mechanically synthesized powder. The method was found to enable not only rapid densification but also the inhibition of grain growth, preserving the nano-scale microstructure. Highly dense $2/3Cr-ZrO_2$ composite with relative density of up to 99.5% was produced under simultaneous application of a 1 GPa pressure and the induced current. The hardness and fracture toughness of the composite were 534 kg/mm2 and $7MPa{\cdot}m1/2$, respectively. The composite was determined to have good biocompatibility.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.32 no.5
• /
• pp.673-678
• /
• 2003

Changran Jeotgal (aged and seasoned intestine of Alaska pollack) was prepared as the same method as commercial one and irradiated at 0, 2.5, 5.0 and 10 k㏉ by gamma ray for industrial application. Changran Jeotgal using 10 k㏉-irradiated red pepper powder was also prepared to compare with control (0 k㏉). Commercial red pepper powder was already contaminated at 3.8$\times$10$^{6}$ CFU/$m\ell$ level by total plate count and 10k㏉ of irradiation reduced the number about 4 log cycles. Gamma irradiated Changran Jeotgal at 2.5,5.0, and 10k㏉ showed 3 6, and 7 log cycles of reduction compared to the non-irradiated control in the total plate count after 12 weeks of storage at 1$0^{\circ}C$. Using irradiated (10k㏉) red pepper powder reduced the microbial contamination significantly by 2 log cycles compared to the control. Sensory evaluation showed that the sample irradiated at 2.5 k㏉ was the most acceptable, followed by the sample using irradiated red pepper powder and non-irradiated control. Thus, 2.5 k㏉ of irradiation of Changran Jeotgal was effective to improve safety during distribution and storage without change of sensory quality. Furthermore, using the irradiated red pepper powder is also recommended for safety enhancement of the products.

• Journal of Powder Materials
• /
• v.17 no.6
• /
• pp.456-463
• /
• 2010

This paper describes the results of the application of Cr-Diamond-like carbon (DLC) films for efficiency improvement through surface modification of spur gear parts in the hydraulic gear pump. Cr-DLC films were successfully deposited on SCM 415 substrates by a hybrid coating process using linear ion source (LIS) and magnetron sputtering method. The characteristics of the films were systematically investigated using FE-SEM, nano-indentation, sliding tester and AFM instrument. The microstructure of Cr-DLC films turned into the dense and fine grains with relatively preferred orientation. The thickness formed in our Cr buffer layer and DLC coating layer were obtained the 487 nm and $1.14\;{\mu}m$. The average friction coefficient of Cr-DLC films considerably decreased to 0.15 for 0.50 of uncoated SCM415 material. The hardness and surface roughness of Cr-DLC films were measured 20 GPa and 10.76 nm, respectively. And then, efficiency tests were performed on the hydraulic gear pump to investigate the efficiency performance of the Cr-DLC coated spur gear. The experimental results show that the volumetric and mechanical efficiency of hydraulic gear pump using the Cr-DLC spur gear were improved up to 2~5% and better efficiency improvement could be attributed to its excellent microstructure, higher hardness, and lower friction coefficient. This conclusion proves the feasibility in the efficiency improvement of hydraulic gear pump for industrial applications.

• New & Renewable Energy
• /
• v.4 no.1
• /
• pp.11-18
• /
• 2008

In-situ lithiated NiO has been manufactured as a conventional cathode material of molten carbonate fuel cell (MCFC), however this material has a weakness for commercialization of MCFC because NiO is spontaneously dissolved into the electrolyte under MCFC operating conditions, resulting in short circuit between cathode and anode. In this research, therefore, $Co(OH)_2$-coated Ni powder was prepared by precipitation method with controlling pH at low temperature and atmospheric pressure. Modified cathode was fabricated by a conventional tape casting method and sintered at 700$^{\circ}C$ in a $H_2/N_2$ atmosphere, Based on characterization result, Pore size distribution and porosity was suitable for the cathode of MCFC. According to the result of dissolution, Ni solubility of modified cathode was 33% lower than that of conventional cathode. In addition, modified electrode showed a good performance from the single cell operation.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.1
• /
• pp.11-15
• /
• 2011

In this study, $ZnGa_2O_4$ phosphors in its application to field emission displays and electroluminescence were synthesized through the precipitation method and $Mn^{2+}$ ions. A green luminescence activator, $Cr^{3+}$ ions, and a red luminescence activator were separately doped into $ZnGa_2O_4$, which was then screen printed to an indium tin oxide substrate. The thick films of the $ZnGa_2O_4$ were deposited with the various thicknesses using nano-sized powder. The best luminescence characteristics were shown at a thickness of 60 ${\mu}m$. Additionally, green-emission $ZnGa_2O_4:Mn^{2+}$ and red-emission $ZnGa_2O_4:Cr^{3+}$ phosphor thick films, which have superior characteristics, were manufactured through the screen-printing method. These results indicate that $ZnGa_2O_4$ phosphors prepared through the precipitation method have wide application as phosphor of the full color emission.

• Journal of the Korean Ceramic Society
• /
• v.43 no.1 s.284
• /
• pp.1-3
• /
• 2006

Well-shaped NaA zeolite cubic crystals of a large size of $5-7{\mu}m$ were synthesized by a hydrothermal method in a mother solution having a $3.55Na_2O:Al_2O_3:1.6SiO_2:593\~2000H_2O$ composition. Thermal treatment of NaA zeolite crystals resulted in the formation of a crystalline phase of $NaAlSiO_4-Camegeite$ between 800 and $900^{\circ}C$. Even at $1000^{\circ}C,\;NaAlSiO_4$ phase was found as a major product. Environmental Scanning Electron Microscopy (ESEM), High Resolution Transmission Electron Microscopy (HRTEM), X-Ray powder Diffraction (XRD), Fourier Transform Infrared (FT-IR) spectroscopy, and DTA/TGA and BET analyses were used to characterize the initial materials and the obtained products after various heat treatments.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.3
• /
• pp.87-99
• /
• 1991

The effect of oven firing on the color stability and surface texture of extrinsic stains used characterization and color modification of metal cermic restoration were studied by comparing different temperatures and techniques. They were autoglaze technique, applied glaze technique, two step low-fusing glaze technique and one step low-fusing glaze technique. Autoglaze technique and applied glaze technique were air-fired to manufacturer's recommended temperature. Two step low-fusing glaze technique is separated staining and overglazing. Thin slurry of stain powder were air-fired to $1500^{\circ}F$, Overglaze powder powder was then mixed with seam medium and air-fired to $170^{\circ}F$. One step low-fusing glaze technique is combined staining and overglazing. Thin slurry of stain and glaze powder were air-fired to $170^{\circ}F$. The obtained results were as fellows. 1. Slightly significant color differences by colorimeter were found between different stain application and fusion techniques(P<0.05). 2. Two step low-fusing glaze method showed the most rough surface, especially ceramco orage stain(P<0.05). 3. Surface roughness increased gradually in order of autoglaze, applied glaze, one step low-fusing glaze but they were not significantly different(P<0.05). 4. When two step low-fusing glaze was applied, both color measurement and surface texture were sinificantly different from other groups(P<0.05).