• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.1
• /
• pp.63-68
• /
• 1998

Irradiation can be utilized to inhibit sprouting of onions and garlic. Thermoluminescence(TL) is a potential method to detect post-irradiation of onions and garlic because they are irradiated with soil or dusts on them, from which minerals can be isolated for TL analysis. This study was to determine whether TL can be applied for the detection of post-irradiation of onions and garlic. Onions and garlic produced in Korea were irradiated in the range of 0.01~0.6kGy. Minerals isolated from the samples using sodium polytrungstate solution were used for TL analysis. The onions and garlic irradiated at 0.15kGy or higher could be detected with little errors. Minimum dose for the 2nd glow could be applied since the dose for the 2nd glow did not affect the results. The TL intensities of the temperature ranges of 229~295$^{\circ}C$ and 229~361$^{\circ}C$ and the maximum intensity provided more accurate information for the determination of the post-irradiation of onions and garlic.

• The Korean Journal of Physiology
• /
• v.5 no.1
• /
• pp.51-58
• /
• 1971

In an attempt to further clarify the effect of X·irradiation on the activity of surfactant in rabbits, X-ray in dose of 900r was irradiated to the lung tissues of rabbits in vitro. Tension-area diagram of the lung extract was recorded automatically by a modified Langmuir-Wilhelmy balance with a synchronized recording system designed in this department. The surface tension of the lung extract was measured at 1,3,5,24 and 48 hours post-irradiation, and the results were compared with the non·irradiated normal group. The result$ thus obtained are summarized as follows: I The maximal surface tension, minimal surface tension, width of the tension·area diagram at the surface area of 40% in the lung extract and stability index of the normal rabbit long extract were 40.73 dynes/cm, 8.96 dynes/cm, 20.71 dynes/cm and 1.28, respectively. II. When 900r of X-ray was irradiated to the lung in vitro, 1) The maximal and minimal surface tensions did not differ noticeably from the normal at 1,3, and 5 post-irradiation hours, but the minimal surface tension increased significantly at 24 and 48 hours Post-irradiation. 2) The width of the tension area at the surface area of 40% showed a tendency of decrease throughout the experiment. 3) The stability index showed no significant change at 1,3 and 5 post-irradiation hours,but at 24 and 48 hours post-irradiation a significant decrease was observed comparing with the control. III. Activity of surfactant was significantly depressed by X·irradiation in vitro especially at 24 and 48 hours post-irradiation.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.42 no.2
• /
• pp.131-138
• /
• 2009

The radioprotect effects of fractinated fucoidan, derived from Undaria pinnatifida sporophylls, were examined in lung injured rats treated with partial body irradiation. The right lung of Sprague-Dawley rats, eight separately grouped by including radiation only control group (ROG) and fucoidan+radiation treated group (FRG), were treated with various fraction of Undaria-derived fucoidan every other day by intraperitoneal injection 6 days prior to irradiation and during monitoring at 24 hours, 48 hours, 2 weeks, 4 weeks and 12-weeks post-irradiation of 6 Mev/2 Gy. The rats were euthanized at completion of the treatment. Tissue samples from the injured lung, fixed in formaldehyde using lung perfusion prior to extraction, were H/E stained for histological analysis using optical microscopy. Interstitial congestion (IC), hemorrhage in alveolar sac (HM), number of macrophage (MP) and alveolar wall thickness (AWT) as a measure of early indication of fibrosis were measured. AWTs in 24 hrs post-irradiation rats increased in comparison with $2.49{\pm}0.06{\mu}m$ of control group by $3.67{\pm}0.09{\mu}m$, $3.21{\pm}0.08{\mu}m$ (p=0.013), $2.98{\pm}0.08{\mu}m$ (p=0.00) in ROG, F1-fucoidan+radiation, and F3-fucoidan+radiation group, respectively. AWT of the ROG was further increased by $4.30{\pm}0.13{\mu}m$ in the 12 weeks post-irradiation group, but AWT on average was $2.56{\pm}0.05{\mu}m$ in the FRG. MP in the 24 hrs post-irradiation group markedly increased in comparison with $2.6{\pm}0.34/0.14\;mm^2$ of the control group by $8.0{\pm}1.48/0.14\;mm^2$ in the ROG, but it was only $3.6{\pm}0.48/0.14\;mm^2$ in F3-FRG. MP in the 12 weeks post-irradiation group was $7.2{\pm}1.28/0.14\;mm^2$ in ROG, but it was $2.8{\pm}0.37/0.14\;mm^2$ or $2.4{\pm}0.4/0.14\;mm^2$ (p<0.05) in the FRG. In addition, increased IC and HM in ROG were relatively smaller in FRG of the 24 hr and 12 weeks post-irradiation rats. In conclusion, Undaria pinnatifida sporophylls-derived fucoidan fractions exhibited radioprotectant activity on injured rat lung subjected to X-ray irradiation. However, success was variable according to the fractions and also time of injection post injury.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.408-420
• /
• 2023

Beryllium oxide (BeO) is being re-emphasized and utilized in Micro Modular Reactors (MMR) because of its prominent nuclear and high temperature properties in recent years. The implications of the research about effects of neutron irradiation on the microstructure and properties of BeO are significant. This article comprehensively reviews the effects of neutron irradiation on BeO and proposes the maximum permissible neutron doses at different temperatures for BeO without cracks in appearance according to the data in the previous literature. This maximum permissible neutron dose value has important reference significance for the experimental study of BeO. The effects of neutron irradiation on the thermal conductivity and flexural strength of BeO are also discussed. In addition, microstructure evolution of irradiated BeO during post-irradiation annealing is summarized. This review article has important implications for the application of BeO in MMR.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.6
• /
• pp.1109-1115
• /
• 1997

Hydrocarbons were analyzed in irradiated beef, pork, dried and seasoned beef, dried anchovy, dried squid, dried shrimp, and fish paste to determine whether the hydrocarbons can be used as markers for detecting post-irradiation of the imported meat and fish products. The samples were irradiated at 0.5, 1, 3, and 6 kGy. Fat was extracted with hexane, and hydrocarbons were separated from the fat through Florisil column. The hydrocarbons were analyzed with GC. Hydrocarbons 15:0, 16:1, 17:1, 16:2, 17:2, and 16:3 in beef and pork, 17:1, 16:2, and 17:2 in dried and seasoned beef, 16:2 in dried anchovy, 16:1 and 17:1 in dried squid, 16:1, 17:1, and 16:2 in dried shrimp, and 16:1, 16:2, and 16:3 in fish paste were detected in the irradiated samples, but not in the unirradiated, so that the hydrocarbons may be used as makers for detecting post-irradiation of each item.

• The Journal of Internal Korean Medicine
• /
• v.25 no.4
• /
• pp.25-33
• /
• 2004

Objective : The effects of Indium-Gallium-Aluminium-Phosphide(InGaAlP) laser transcutaneous irradiation on heart rate variability(HRV) in healthy adults are investigated with power spectrum analysis(PSA) of HRV. Methods : The control group consisted of 20 healthy volunteers (10 men, 10 women). The experiment was divided into 5 different periods, the pre-1st laser period(10 minutes), the 1st laser period(30 minutes), the post-1st laser period(5 minutes), the 2nd laser period( 30 minutes) and the post-2nd laser period(30 minutes). HRV was measured for 5 minutes at the pre-1 st laser period, the post-l st laser period and the post-2nd laser period. The laser period is the period in which InGaAlP laser transcutaneous Irradiation treatment occurs. Results : 1. SDNN of volunteers at post-1st laser period and post-2nd laser period significantly increased compared with that of the pre- 1 st laser period. 2, Ln(VLF) at post-I st laser period significantly increased compared with that of pre-1st laser period, while Ln(HF) at post-2nd laser period significantly decreased compared with those of pre- I st laser period and post-1st laser period, 3. Ln(TP) at post-1st laser period and post-2nd laser period significantly increased compared with that of pre-1st laser period, 4, LF/HF Ratio at post-2nd laser period significantly increased compared with those of pre-1st laser period and post-1st laser period. But the other variables did not significantly change. Conclusions : The results suggest that InGaAlp laser transcutaneous Irradiation in healthy adults is associated with the autonomic nervous systems. Further study is needed for investigating the effects of laser irradiation on autonomic nervous systems.

• Parasites, Hosts and Diseases
• /
• v.49 no.1
• /
• pp.25-31
• /
• 2011

Cryptosporidium parvum is known as one of the most highly resistant parasites to gamma irradiation. To morphologically have an insight on the radioresistance of this parasite, ultrastructural changes in C. parvum sporozoites were observed after gamma irradiation using various doses (1, 5, 10, and 25 kGy) following a range of post-irradiation incubation times (10 kGy for 6, 12, 24, 48, 72, and 96 hr). The ultrastructures of C. parvum oocysts changed remarkably after a 10-kGy irradiation. Nuclear membrane changes and degranulation of dense granules were observed with high doses over 10 kGy, and morphological changes in micronemes and rhoptries were observed with very high doses over 25 kGy. Oocyst walls were not affected by irradiation, whereas the internal structures of sporozoites degenerated completely 96 hr post-irradiation using a dose of 10 kGy. From this study, morphological evidence of radioresistance of C. parvum has been supplemented.

• Nuclear Engineering and Technology
• /
• v.54 no.11
• /
• pp.4084-4094
• /
• 2022

The Advanced Fuels Campaign Fission Accelerated Steady-state Test (FAST) at Idaho National Laboratory (INL) completed its first irradiation cycle within the Advanced Test Reactor (ATR). The test focused on the irradiation of alloy fuel forms for use in sodium fast reactors. The first cycle of FAST testing was completed and four rodlets were removed for the initial post irradiation examination (PIE). The rodlet design and irradiation conditions were evaluated using Monte Carlo N-Particle (MCNP) for as-run power history and COMSOL for temperature analysis. These rodlets include a set of low burnups (~2.5 % fissions per initial metal atoms [%FIMA]), control rodlets, and a helium-bonded annular rodlet (4.7 %FIMA). Nondestructive PIE has been completed and includes visual inspection, neutron radiography and gamma scanning of the FAST capsules and rodlets. Radiography confirmed the integrity of the experiments, revealed that the annulus in the annular fuel was filled at a modest burnup (4.7 %FIMA), and indicated potential slumping of the cooler rodlets at lower burnup. Precision gamma scanning indicated mostly usual fission product behavior, except for cesium in the He-bonded annular fuel. Future destructive PIE will be necessary to fully interpret the effects of accelerated irradiation on U-Zr metallic fuel behavior.

• Nuclear Engineering and Technology
• /
• v.54 no.3
• /
• pp.991-996
• /
• 2022

Microstructures of monolithic high purity SiC and SiC with sintering additives after neutron irradiation to a fluence of 2.0-2.5 × 10²⁴ n/m² (E > 0.1 MeV) at 333-363 K and after post-irradiation annealing up to 1673 K were observed using a transmission electron microscopy. Results showed that no black spot defects or dislocation loops in SiC grains were found after the neutron irradiation for all of the specimens owing to the moderate fluence at low irradiation temperature. Thus, it is confirmed that these specimens were swelled mostly by the formation of point defects. Black spots and small dislocation loops were discovered only after the annealing process in PureBeta-SiC and CVD-SiC, where the swelling almost diminished. Anomalous-shaped YAG grains were found in SiC ceramics containing sintering additives. These grains contained dense black spots defects and might lose crystallinity after the neutron irradiation, while these defects may annihilate by recrystallization during annealing up to 1673 K. Amorphous grain boundary phase was also presented in this ceramic, and a large part of it was crystallized through post-irradiation annealing and could affect their recovery behavior.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.347.1-347.1
• /
• 2014

최근, 박막 트랜지스터는 빠른 동작 속도, 낮은 공정비용 그리고 저온공정 등의 특성을 필요로 하고 있다. 그 중 indium-zinc oxide (InZnO)는 높은 전기적 특성, 높은 광 투과도 그리고 우수한 안정성 때문에 기존의 반도체를 대체할 수 있을 것으로 기대된다. InZnO의 경우 indium과 zinc의 조성비에 따라 특성 변화의 차이가 크기 때문에 다양한 조성비에 대한 연구가 보고되고 있는데, 기존의 InZnO 박막을 증착하는 방법의 경우에 조성비의 변화 과정에 많은 공정상의 어려움이 있다. 이 같은 문제점 때문에 조성비의 변화를 용이하게 할 수 있는 용액공정을 이용한 연구가 진행되고 있다. 또한 용액공정은 높은 균일성, 공정 시간 및 비용 감소 그리고 대면적화가 가능한 장점을 가지고 있다. 한편, 용액공정을 기반으로 한 InZnO의 경우에 용액 상태에서 고체 상태의 순수한 금속 산화물 상태로 바꾸기 위해 post-treatment 가 필요하다. 일반적으로 furnace 열처리 방법을 사용하는데, 이 경우 낮은 열효율 및 고비용 등의 문제점을 가지고 있다. 특히 glass 또는 flexible 기판의 경우 열처리 온도에 대한 제약이 있다. 이러한 문제를 해결하기 위한 방법으로 최근에 microwave irradiation를 이용한 저온 post-treatment 방법이 보고되고 있다. Microwave irradiation는 짧은 공정시간 및 열 균일성 등의 장점이 있다. 따라서 본 연구에서는 다양한 indium과 zinc의 조성비를 갖는 용액을 제작한 후 spin coating을 이용하여 증착한 InZnO 기반의 박막 트랜지스터를 제작하였다. Furnace와 microwave 방식으로 post-treatment 하여 비교 평가한 결과 microwave irradiation 한 경우 furnace 열처리 한 경우 보다 더 안정된 동작 전압을 가지는 것으로 나타났다. 따라서 저온공정이 가능한 microwave irradiation 방법으로 post-treatment 한다면 차세대 산화물 반도체로서의 적용이 가능할 것으로 기대된다.