• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.948-951
• /
• 2008

Ubiquitous sensor network (USN) based on ZigBee communication protocol has been used in various application fields, such as home-network, intelligent building and machine, logistics, environmental monitoring, military field, security field and etc. The ZigBee is targeted at radio-frequency application that require a low data rate, long battery life and secure network. Especially, the USN system can be applied efficiently to building-indoor where the complex geometry is adopted. In this study, all 90 points of railway cabin indoor were monitored for temperature and humidity using USN technology. All sensors were pre/post-calibrated and the temperature/humidity change were analyzed in a railway cabin in real-time. The results would be useful to develop the cabin heating, ventilating and air conditing (HVAC) system to meet all passengers' thermal comfort regardless of their seat position.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1995년도 특별강연 및 춘계학술발표 개요집
• /
• pp.91-93
• /
• 1995

A study was made to examine the effects of post-weld heat treatment (PWHT) on the toughness and microstructures in the weld heat-affacted zone(HAZ) of Cu-bearing HSLA-100 steel. The Gleeble thermal/mechanical simulator was used to simulate the weld HAZ. The behavior of Cu-precipitates in HAZ is similar to that in base plate. PWHT at 55$0^{\circ}C$ shows highest hardness and lowest toughness, whereas PWHT at $650^{\circ}C$ shows reasonable toughness. Cu precipitated during agcing for increasing the strength of base metal is dissolved during single thermal cycle to 135$0^{\circ}C$ and is precipitated little on cooling and heating during subsequent weld thermal cycle. It precipitates by introducing PWHT.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권4호
• /
• pp.770-783
• /
• 2015

Lately, high production rate welding processes for Al alloys, which are used as LNG FPSO cargo containment system material, have been developed to overcome the limit of installation and high rework rates. In particular, plasma-metal inert gas (MIG) hybrid (PMH) welding can be used to obtain a higher deposition rate and lower porosity, while facilitating a cleaning effect by preheating and post heating the wire and the base metal. However, an asymmetric undercut and a black-colored deposit are created on the surface of PMH weld in Al alloys. For controlling the surface defect formation, the wire feeding speed and nozzle diameter in the PMH weld was investigated through arc phenomena with high-speed imaging and metallurgical analysis.

• 한국표면공학회지
• /
• 제52권6호
• /
• pp.289-292
• /
• 2019

Transparent and conducting titanium doped indium oxide (TIO) thin films were deposited by RF magnetron sputtering on zinc oxide (ZnO)-coated glass substrates to investigate the effect of the ZnO buffer layer on optical and electrical properties of TIO/ZnO bi-layered films. TIO 90 nm / ZnO 10 nm films having a lower resistivity (3.09×10^-3 Ωcm) and a higher visible transmittance (80.3%) than other TIO/ZnO films were prepared in this study. Figure of merit results indicate that a 10 nm thick ZnO thin film is an effective buffer layer that enhances optical transmittance and electrical conductivity of TIO films without intentional substrate heating or post-deposition annealing.

• 암석학회지
• /
• 제3권1호
• /
• pp.20-33
• /
• 1994

Some of the seven types of subgrain boundaries (Means and Ree, 1988) in octachloropropane samples show distinctive deformation patterns during their development. Type II subgrain boundaries migrate to accommodate the deformation difference between adjacent grains. The formation of Type III requires a rigid-body roation of grains to reduce misorientation of adjacent grains. Type I, IV, V and VI develop either in static or dynamic condition. Type VII form only in static environments after deformation. Ribbon grains can develop via Type III or Type IV process. The orientation pattern and density of subgrain boundaries are more or less stable through a post-deformation heating. Subgrain boundary orientations are symmetric with respect to the grain-shape foliation in pure shear. In simple shear, their maximum inclines toward the direction of shear.

• Computers and Concrete
• /
• 제23권3호
• /
• pp.155-160
• /
• 2019

The use of recycled aggregate concrete for the purpose of environmental and resource conservation has gained increasing interest in construction engineering. Nevertheless, few studies have reported on the bonding performance of the bars in recycled aggregate concrete after exposed to high temperatures. In this paper, 72 pull-out specimens and 36 cubic specimens with different recycled coarse aggregate content (i.e., 0%, 50%,100%) were cast to evaluate the bond behavior between recycled aggregate concrete and steel bar after various temperatures ($20^{\circ}C$, $200^{\circ}C$, $400^{\circ}C$, $600^{\circ}C$). The results show that the recycled aggregate concrete pull-out specimens exhibited similar bond stress-slip curves at both ambient and high temperature. The bond strength declined gradually with the increase of the temperature. On the basis of a regression analysis of the experimental data, a revised bond strength mode and peak slip ratios relationship model were proposed to predict the post-heating bond-slip behavior between recycled aggregate concrete and steel bar.

• Journal of the Korean Wood Science and Technology
• /
• 제36권1호
• /
• pp.21-29
• /
• 2008

서울시 내에 소재한 현재까지 이용되고 있는 목조건물에 대한 열화 조사를 실시하였다. 조사된 목조건물은 겨울철임에도 흰개미에 의한 피해가 진행되고 있었다. 목조건물의 흰개미 피해 실태 및 원인을 조사하기 위하여 초음파에 의한 비파괴 방법을 적용하였으며, 환경적 열화요인 조사에는 적외선 카메라를 사용하였다. 비파괴 검사를 통한 기둥부재의 내구성을 조사한 결과 일부 기둥 부재에서는 심각한 강도적 손실이 발견되어 교체가 필요하였다. 조사된 목조건물은 사람이 생활하기 위하여 현대식 난방설비를 설치한 곳으로서 전통적인 목조건물 내부에 난방시스템이 설치됨으로써 연중 비교적 균일한 온도대의 형성 그리고 바닥재에 의한 결로발생으로 인한 수분 제공이 흰개미의 피해가 발생되는 원인으로 작용하게 되었다. 조사한 목조건물의 흰개미는 일본흰개미, Reticulitermes speratus로 동정되었다. 목조건물은 주위환경에 따라서 많은 영향을 받으므로 환경 조절을 통하여 생물열화를 방지할 수 있는 유지 관리 기술이 필요하였다. 전통건물 내 현대식 시설의 설치는 전통목조건물의 특징을 잘 살리고 내구성에 영향이 없는 시설의 설치가 바람직하다고 판단되었다.

• 원예과학기술지
• /
• 제33권3호
• /
• pp.349-355
• /
• 2015

Lisianthus (Eustoma grandiflorum) is relatively sensitive to temperature and light conditions. For year round production of good quality potted plants and energy saving, it is necessary to understand the growth and flowering response to the combined conditions of these environmental factors. This study was conducted to examine the growth and flowering responses to temperature, photoperiod, and light intensity during the post-seedling stage. 'El Paso Deep Blue' lisianthus plants with four true leaf pairs were grown in growth chambers maintained at average daily temperatures (ADT) of 14, 20, and $26^{\circ}C$ and provided with three photosynthetic photon fluxes [PPF; 100, 200, and $400{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$] for 8 (08:00-16:00) and 16 hours (08:00-24:00) by fluorescent and incandescent lamps, resulting in four daily light integrals (DLI): about 3, 6 (two photoperiods), 12 (two photoperiods), and $24mol{\cdot}m^{-2}{\cdot}d^{-1}$. After treatment for three weeks followed by growth for one week in a greenhouse of $20{\pm}3^{\circ}C$, growth and development were measured. Higher temperature, higher PPF, and longer photoperiod promoted plant growth and flowering; however the impacts of PPF and photoperiod were smaller than those of temperature. As ADT and DLI increased, the number of leaves, number of flowers, lateral shoot length, and shoot dry weight increased. An increase of about $1mol{\cdot}m^{-2}{\cdot}d^{-1}$ DLI could constitute an increase of 0.40 to $0.76^{\circ}C$ ADT depending on these crop characteristics when ADT and DLI are above $20^{\circ}C$ and $12mol{\cdot}m^{-2}{\cdot}d^{-1}$, respectively. Therefore, growers can select a regimen of heating or supplemental lighting without delaying harvesting time or decreasing crop quality.

• 한국진공학회지
• /
• 제5권3호
• /
• pp.239-244
• /
• 1996

비정질 Si 막의 증착을 위해 승온시 $Si_2H_6$ 가스를 주입함으로써 Si 표면의 $SiO_2$ 의 형성을 방지할 수 있었다. 또한 이렇나 공정을 이용하여 증착된 비정질 Si 의 후열처리에 의한 고상 에피텍시 성장이 가능하였다. 승온시 $Si_2H_6$ 가스 주입에 의한 표면 $SiO_2$의 형성 방지는 증착 승온시 SiHx 분위기를 만들어 줌으로써 , Si 기판표면의 passivation H의 탈착과 동시에 일어나는 반응기 잔류 가스중에 의한 O의 흡착대신 SiHx를 흡착시킴으로써 가능한 것으로 판단된다. 이러한 방법을 이용하여 기존에 보고된 고온 cleaning 공정없이도 고품위의 결정성을 갖는 에피텍시 막을 $600^{\circ}C$미만의 저온 공정으로 제조할 수 있었다.

• Journal of Welding and Joining
• /
• 제32권3호
• /
• pp.95-101
• /
• 2014

Joining of grey cast iron by fusion welding has much difficulties for its extremely low ductility and low toughness because of the flake form of the graphite. And the brittle microstructure, i.e. ledeburite may be formed during fusion welding by its rapid cooling rates. By these kinds of welding problem, preheat and post heat treatment temperature must be increased to avoid weld crack or welding problems. In order to avoid these fusion welding problem, friction welding of cast iron was carried out for improving joint soundness, establishing friction welding variables. There is no factor for evaluating friction weldability in continuous drive type friction welding. In this point of view, this study proposed the parameters for calculating friction weld heat input. The results obtained are as follows ; 1. There was a close relationship between tensile strength and flash appearance of friction welded joint. 2. Tensile strength was decreased and flash was severely oxidized as increasing frictional heating time. 3. As increased forging pressure $P_2$, flash had a large crack and tensile strength was decreased. 4. As powdered graphite by rotational frictional force induced flat surface and hindered plastic flow of metal, tensile strength of welded joint was decreased. 5. Heat input for continuous drive type friction welding could be calculated by the factors of $P_1$, $P_2$ and upset distance(${\delta}$).