• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2003.04a
• /
• pp.54-69
• /
• 2003

Print gloss is an important attribute of the final printed product. While past work has looked at the influence of key aspects of the coating structure on print gloss, a systematic study has not been reported. The coating roughness, porosity, and pore size are changed by using various combinations of coating materials and by calendering against rough plastic sheets. The print gloss is measured every tenths of a second right after printing, a few minutes after printing, and a few days afterwards. Roughness and porosity affect the print gloss for the first two seconds: this result shows that they influence the ink-film splitting event. Once ink film starts to level, roughness and pore size influences the level of print gloss within the first ten seconds after printing. Porosity modifies the evolution of print gloss for the next few minutes. The decrease in gloss at long times is found to correlate to surface roughness.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.11
• /
• pp.3749-3754
• /
• 2012

Nanoporous carbons with a high specific surface area were prepared directly from thermoplastic acrylic resin as carbon precursor and MgO powder as template by carbonization over the temperature range, $500-1000^{\circ}C$. The effect of the carbonization temperature on the pore structure and $CO_2$ adsorption capacity of the obtained porous carbon was examined. The textural properties and morphology of the porous carbon materials were analyzed by $N_2/-196^{\circ}C$ and $CO_2/0^{\circ}C$ adsorption/desorption isotherms, SEM and TEM. The $CO_2$ adsorption capacity of the prepared porous carbon was measured at $25^{\circ}C$ and 1 bar and 30 bar. The specific surface area increased from 237 to $1251m^2/g$, and the total pore volumes increased from 0.242 to $0.763cm^3/g$ with increasing the carbonization temperature. The carbonization temperature acts mainly by generating large narrow micropores and mesopores with an average pore size dependent on the level of carbonization of the MgO-templated nanoporous carbons. The results showed that the MgO-templated nanoporous carbons at $900^{\circ}C$ exhibited the best $CO_2$ adsorption value of 194 mg/g at 1 bar.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.3
• /
• pp.29-36
• /
• 2001

This paper was made to evaluate the effect of the blending ration of GCC and No. 1 clay on the printability by investigating the structure of pore such as the pore rate, the number of pores, pore size and distribution of coated paper. The coated structure is mainly depended on the results of correlation between pigment and binder. It means that the structure of the pore occurred is chiefly affected by the blending ratio of GCC and No. 1 clay. This physical properties of the pore have a close relation with ink set-off associated with the drying rate and the penetration in ink into base paper and with printing gloss. Therefore it was needed to find out how the pore structure and the printability will be changed by modifying the blending ratio of GCC and No. 1 clay to vary the pore structure of coated paper. Below are the results of measurement: As the blending ratio of clay going up, water retention, sedimentation volume. smoothness, and paper gloss were increased, but relatively brightness and opacity were decreased. Pore rate was the highest at the blending ratio of No. 1 clay to GCC, 70:30. In this case, average pore radius was also increased. Ink receptivity and K&N ink receptivity were improved with the increase of the blending ratio of GCC, where was, ink setting was vice versa. No difference was observed in the weight of ink, but ink repellance decrease with the decrease of blending ratio of GCC.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.4D
• /
• pp.577-584
• /
• 2011

A series of field and laboratory permeability tests were performed to investigate the pore-clogging phenomenon of porous concrete used for pavement materials of a road. The field permeability tests were conducted for 37 study points in Jeju city, using the porous concretes with 13mm of maximum coarse aggregate ($G_{max}$). The results show that the service life of porous concrete is about 22 months when the permeability of the porous concrete is designed for 0.01 cm/sec. Some specimens were made with the purpose of recreating pore-clogging phenomenon. Tests were done for injected concentration of pore-clogging materials or size of maximum coarse aggregates ($G_{max}$). The test results demonstrated that relatively long in service life experienced with small amount of injected concentration of pore-clogging materials, whereas relatively short in service life experienced with a reduction in size of maximum coarse aggregates ($G_{max}$). In conclusion, the service life of porous concrete is in proportion to the concentration of pore-clogging material but it is in inverse proportion to the size of maximum coarse aggregate ($G_{max}$). Thus, the persisting period of porous concrete can be determined with respect to concentration of pore-clogging materials or size of maximum coarse aggregates ($G_{max}$).

• Journal of Environmental Science International
• /
• v.17 no.1
• /
• pp.67-75
• /
• 2008

Adsorption process is largely influenced by pore structures of adsorbents and physical properties of adsorbates and adsorbents. The previous studies of this laboratory was focused on the role of pore structures of adsorbents. And we found some pores of adsorbates which have larger pore diameters than the diameter of adsorbate are filled with easily. In this study the effects of physical and chemical properties of adsorbates and adsorbents, such as pore size distribution, vapor pressure on adsorption were investigated more thoroughly at the concentration of adsorbate of 1000 ppm. The adsorption in the pore ranges of $2{\sim}4$ times of adsorbates's diameter could be explained by space filling concept. But there was some condensation phenomena at larger pore ranges. The errors between the adsorbed amount of non-polar adsorbates and the calculated amounts by considering factors were found to be 44.46%, positively, and -142%, negatively. When vapor pressure is considered, the errors between the adsorbed amount of non-polar adsorbates and the calculated amounts were in the range of $1.69%{\sim}32.25%$ positively, and negatively $-1.08%{\sim}-63.10%$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.53-53
• /
• 2003

There has been increasing interest in the fabrication of nano-sized structures because of their various advantages and applications. Anodic Aluminum Oxide (AAO) is one of the most successful methods to obtain highly ordered nano pores and channels. Also It can be obtained diverse pore diameter, density and depth through the control of anodization condition. The three types of substrates were used for anodization; sheets of Aluminum on Si wafer and Aluminum on Mo-coated Si wafer. In Aluminum sheet, a highly ordered array of nanoholes was formed by the two step anodization in 0.3M oxalic acid solutions at 10$^{\circ}C$ After the anodization, the remained aluminum was removed in a saturated HgCl$_2$ solution. Subsequently, the barrier layer at the pore bottom was opened by chemical etching in phosphoric acid. Finally, we can obtain the through-channel membrane. In these processes, the effect of various parameters such as anodizing voltage, anodizing time, pore widening time and pre-heat treatment are characterized by FE-SEM (HITACH-4700). The pore size. density and growth rate of membrane are depended on the anodizing voltage and temperature respectively. The pore size is proportional to applied voltage and pore widening time The pore density can be controlled by anodizing temperature and voltage.

• Transactions of Materials Processing
• /
• v.27 no.2
• /
• pp.93-99
• /
• 2018

An analytical solution for the tensile ductility in porous ductile materials was derived based on an Irwin's approach of the elastic-plastic deformation in fracture mechanics. This was in good agreement with the experimental results of a tensile ductility in a sintered pure Al, and could solve the discrepancies in the Brown and Embury, or the McClintock models. This model was also offered as an advanced analytical solution considering the effect of stress triaxiality of pore tip in addition to pore interactions, material properties of matrix, and local deformation effect around pore. The evaluation of an analytical solution in the sintered pure Al powder compacts showed that the tensile ductility depends not only on the volume fraction of pores, but also on the pore size and on the mechanical properties of the matrix. The tensile ductility of the sintered pure Al compacts decreased rapidly with the increasing of a pore volume fraction, despite of the excellent tensile ductility of the matrix. This significant decrease in the tensile ductility was mainly attributed to the low yield strength of the matrix and small pore size. Particularly, the effects of the large radius and high volume fraction of the pore on the tensile ductility in Al-Form, were thus reasonably predicted by this analytical equation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.2
• /
• pp.61-67
• /
• 2005

In this study a new growing method of silicon nitride whiskers in the inside of large pores made intentionally during the sintering was conducted. Pore size, pore vol%, and nitrogen pressure were used as experimental variables. Silicon nitride whiskers were well grown in the inside of pores with low pore vol% range from 14 to 27 but not grown with high pore vol% such as 39 and 50. On the other hand, pore size and nitrogen pressure did not have any influence on the whisker growth. Therefore the most important factor to grow silicon nitride whisker in the inside of large pores during sintering was to make pores isolated or closed.

• Structural Monitoring and Maintenance
• /
• v.7 no.2
• /
• pp.69-84
• /
• 2020

Based on differential quadrature method (DQM) and nonlocal strain gradient theory (NSGT), forced vibrations of a porous functionally graded (FG) scale-dependent beam in thermal environments have been investigated in this study. The nanobeam is assumed to be in contact with a moving point load. NSGT contains nonlocal stress field impacts together with the microstructure-dependent strains gradient impacts. The nano-size beam is constructed by functionally graded materials (FGMs) containing even and un-even pore dispersions within the material texture. The gradual material characteristics based upon pore effects have been characterized using refined power-law functions. Dynamical deflections of the nano-size beam have been calculated using DQM and Laplace transform technique. The prominence of temperature rise, nonlocal factor, strain gradient factor, travelling load speed, pore factor/distribution and elastic substrate on forced vibrational behaviors of nano-size beams have been explored.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.548-551
• /
• 2004

For the improvements in high transmittance, one of the most important factors of transparent dielectric is pore contents and pore size. This study have investigated the effect of frit size on the transmittance of zinc-boric system with a Pb-free composition. A mixed glass paste was used for thick films, which were made by screen printing methods on a glass substrate (PD200). These dielectric layers were measured for surface roughness, pores content and transmittance. The results show that increase of pore size and content have detrimental effects on the transmittance of films compared to those found in the PbO system.