• Applied Chemistry for Engineering
• /
• v.30 no.1
• /
• pp.29-33
• /
• 2019

Carbon nanotubes, nanofibers and powders were used for acetylene adsorption experiments. A total of 15 different experiments were designed by 3-level of Box-Behnken Design (BBD) with 3 factors including the Pd concentration of 0 to 5%, adsorption temperature of 30 to $80^{\circ}C$ and $C_2H_2/CO_2$ of 3 to 10. Based on those data, a second order polynomial regression analysis was used to derive the adsorption amount prediction equation according to operating conditions. The adsorption temperature showed the greatest influence index while the $C_2H_2/CO_2$ ratio showed the smallest according to the F-value measurement of the ANOVA analysis. However, there was little interaction between major factors. In the adsorption optimization analysis, a 22.0 mmol/g was adsorbed under the conditions of Pd concentration of 3.0%, adsorption temperature of $47^{\circ}C$ and $C_2H_2/CO_2$ of 10 with 95.9% accuracy.

• Fisheries and Aquatic Sciences
• /
• v.24 no.3
• /
• pp.129-137
• /
• 2021

Dietary protein requirements of abalone (Haliotis discus) depending on abalone size were determined and compared. One thousand and fifty small abalone (initial weight of 2.7 g) and five hundred forty large one (initial weight of 16.0 g) were distributed into 15 and 18 containers in Trial 1 and 2, respectively. Five and six experimental diets containing crude protein level from 20% to 40% and 20% to 45% with 5% increment of protein level for the small and large abalone were prepared and referred to as the CP20, CP25, CP30, CP35, CP40, and CP45 diets, respectively. The experimental diets were fed to abalone for 16 weeks in Trials 1 and 2. Specific growth rate (SGR) of the small abalone fed the CP20 diet was lower compared to that of abalone fed all other diets in Trial 1. Growth performance (weight gain and SGR) of the large abalone fed the CP30, CP35, and CP40 diets were greater than that of abalone fed the CP20, CP25, and CP45 diets in Trial 2. Dietary protein requirements were estimated to be 33.0% and 33.5% for the small and large abalone based on the 2^nd order polynomial analysis, respectively. Dietary protein requirements for the small abalone grown from 2.7 g to 7.4 g and the large one grown from 16 g to 21 g were estimated to be 33.0% and 33.5%, respectively. Size differences in abalone did not affect dietary protein requirement under this experimental conditions.

• Korean Journal of Metals and Materials
• /
• v.49 no.7
• /
• pp.570-576
• /
• 2011

The shape of a dendrite tip has long been approximated by a paraboloid of revolution, but many attempts have been made as well to more accurately match the dendrite tip profile using other mathematical functions: power function, 4th order polynomial, and hyperbolic function. In the present work, dendrite tip shapes were matched by parabolic function. The differences between the dendrite tip shapes of pivalic acid(PVA)-ethanol(Eth) and succinonitrile(SCN)-salol systems, characterized by anisotropic and isotropic solid-liquid interfacial properties, respectively, were quantitatively treated using shape parameters. The PVA-Eth system showed a slightly higher Z/R value than the SCN-salol system, their Z/R values lying in the range 2-4. (Z is the distance from the tip beyond which the parabolic fit starts to deviate from the profile, and R the tip radius.) ${\lambda}_P$ is the distance from the tip beyond which side branching starts to appear, and is larger in the PVA-Eth system than the SCNsalol system. ${\lambda}_P$ is different for both sides of the 2-dimensional dendrite profile. The difference of ${\lambda}_P$ between both sides of the dendrite is larger for PVA-Eth system than for SCN-salol, implying that the dendrite of PVA-Eth is less symmetric than that of SCN-salol.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.14 no.2
• /
• pp.15-22
• /
• 2004

For an ElGamal-type signature scheme using a generate g of order q, it has been well-known that the message nonce should be chosen randomly in the interval (0, q-1) for each message to be signed. In (2), H. Kuwakado and H. Tanaka proposed a polynomial time algorithm that gives the private key of the signer if two signatures with message nonces 0＜$k_1$, $k_2$$\leq$Ο(equation omitted) are available. Recently, R. Gallant, R. Lambert, and S. Vanstone suggested a method to improve the efficiency of elliptic curve crytosystem using integer decomposition. In this paper, by applying the integer decomposition method to the algorithm proposed by Kuwakado and Tanaka, we extend the algorithm to work in the case when ｜$k_1$ ｜,｜$k_2$, ｜$\leq$Ο(equation mitted) and improve the efficiency and completeness of the algorithm.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.39 no.1
• /
• pp.1-11
• /
• 2021

This paper presents a procedure to extract lane line models using a set of proposed methods. Firstly, an image warping method based on homography is proposed to transform a target image into an image which is efficient to find lane pixels within a certain region in the image. Secondly, a method to use the combination of the results of edge detection and HSL (Hue, Saturation, and Lightness) transform is proposed to detect lane candidate pixels with reliability. Thirdly, erroneous candidate lane pixels are eliminated using a selection area method. Fourthly, a method to fit lane pixels to quadratic polynomials is proposed. In order to test the validity of the proposed procedure, a set of black-box images captured under varying illumination and noise conditions were used. The experimental results show that the proposed procedure could overcome the problems of color-only and edge-only based methods and extract lane pixels and model the lane line geometry effectively within less than 0.6 seconds per frame under a low-cost computing environment.

• Journal of Advanced Navigation Technology
• /
• v.26 no.2
• /
• pp.119-124
• /
• 2022

The international gnss service (IGS) provides real-time service (RTS) orbit and clock correction applicable to the broadcast ephemeris of GNSS satellites. However, since the RTS correction cannot be received if the Internet connection is lost, the RTS correction should be predicted and used when a signal interruption occurs in order to perform stable precise point positioning (PPP). In this paper, PPP was performed by predicting orbit and clock correction using a long short-term memory (LSTM) algorithm in real-time during the signal loss. The prediction performance was analyzed by implementing the LSTM algorithm in RPI (raspberry pi), the processing speed of which is not high. Compared to the polynomial prediction model, LSTM showed excellent performance in long-term prediction.

• Journal of The Korean Astronomical Society
• /
• v.54 no.4
• /
• pp.113-119
• /
• 2021

It is difficult for observers to conduct an optical alignment at an observatory without the assistance of an optical engineer if optomechanical parts are to be replaced at night. We present a practical tilt correction method to obtain the optimal optical alignment condition using the symmetricity of optical aberrations of a wide-field on-axis telescope at night. We conducted coarse tilt correction by visually examining the symmetry of two representative star shapes obtained at two guide chips facing each other, such as east-west or north-south pairs. After coarse correction, we observed four sets of small stamp images using four guide cameras located at each cardinal position by changing the focus positions in 10-㎛ increments and passing through the optimum focus position in the range of ±200 ㎛. The standard deviation of each image, as a function of the focus position, was fitted with a second-order polynomial function to derive the optimal focus position at each cardinal edge. We derived the tilt angles from the slopes converted by the distance and the focus position difference between two paired guide chip combinations such as east-west and north-south. We used this method to collimate the on-axis wide-field telescope KMTNet in Chile after replacing two old focus actuators. The total optical alignment time was less than 30 min. Our method is practical and straightforward for maintaining the optical performance of wide-field telescopes such as KMTNet.

• Progress in Medical Physics
• /
• v.32 no.4
• /
• pp.179-184
• /
• 2021

This study aimed to determine the optimal thickness of the active layer and scan mode for a flexible radiochromic film (F-RCF) based on the active lithium salt of pentacosa-10,12-diynoic acid (LiPCDA). F-RCFs of 90, 120, 140, and 170-㎛ thickness were fabricated using LiPCDA. Several pieces of the F-RCFs were exposed to doses ranging from 0 to 3 Gy. Transmission and reflection modes were used to scan the irradiated F-RCFs. Their dose-response curves were obtained using a second-order polynomial equation. Their sensitivity was evaluated for both scanning modes, and the uniformity of the batch was also examined. For both the transmission and reflection modes, the sensitivity increased as the film thickness increased. For the reflection mode, the dose response increased dramatically under 1 Gy. The value of the net optical density varied rapidly as the thickness of the film increased. However, the dose-response curves showed a supralinear-curve relationship at doses greater than 2 Gy. The sensitivity of the reflection scan at doses greater than 2 Gy was higher than that of the reflection scan within 0-2 Gy. The sensitivity steadily decreased with increasing doses, and the sensitivity of the two modes was within 0.1 to 0.2 at 2 Gy and was saturated beyond that. For the transmission scan, the sensitivity was approximately 0.2 at 3 Gy. For the intra-batch test result, the maximum net optical density difference of the intra-batch was 5.5% at 2 Gy and 7.4% at 0.2 Gy in the transmission and reflection scans, respectively. In the low-dose range, film thickness of more than 120-㎛ was proper in the transmission mode. In contrast, the transmission mode showed a better result compared to the reflection mode. Therefore, the proper scan mode should be selected according to the dose range.

• Journal of the Korea Society for Simulation
• /
• v.19 no.1
• /
• pp.73-82
• /
• 2010

Productivity improvement is considered as one of hot potato topics in international shipyards by the increasing amount of orders. In order to improve productivity of lines, shipbuilders have been researching and developing new work method, process automation, advanced planning and scheduling and so on. An optimization approach was accomplished on short-term scheduling of subassembly lines in this research. The problem of subassembly line scheduling turned out to be a non-deterministic polynomial time problem with regard to SKID pattern’s sequence and worker assignment to each station. The problem was applied by simulated annealing algorithm, one of meta-heuristic methods. The algorithm was aimed to avoid local minimum value by changing results with probability function. The optimization result was compared with discrete-event simulation's to propose what pros and cons were. This paper will help planners work on scheduling and decision-making to complete their task by evaluation.

• Analytical Science and Technology
• /
• v.20 no.5
• /
• pp.370-382
• /
• 2007

In this study, solid-phase microextraction (SPME) technique using GC/FID was studied as a possible alternative to liquid-liquid extraction for the analysis of EGBE, DGBE, DBM and TGME in water, and an optimization condition of trace analysis of EGBE, DGBE, DBM and TGME using the factorial design was described. Experiments used a fractional factorial design method followed by central composite design allowing optimization of a number of factors as well as statical analysis of results. The response surface analysis showed that the extraction efficiency can be described by a second-order polynomial equation in which the salts concentration, extraction temperature, extraction time and sonication time are the major influences. Using DOE, a new data-dependent method was developed that improved the quantity of confidently analyzed EGBE, DGBE, DBM and TGME in water samples.