• Elastomers and Composites
• /
• v.51 no.4
• /
• pp.342-349
• /
• 2016

Characteristics of the swelling-induced wrinkles on the surfaces of natural rubber (NR) film were investigated. The wrinkle structure was generated by swelling of NR film pre-stretched and firmly bonded onto an aluminum substrate in hexane. A novel experimental method was adopted to replicate the swelling-induced wrinkles on the NR film using an epoxy-hardener system. To get insight into the wrinkle parameters; the wrinkle length (L), wrinkle distance (D), wrinkle height (H) and the angle between two consecutive wrinkles (${\theta}$), the cross-sections of the replicas obtained from saturated swollen NR film were examined using an optical microscopy (OM). From the OM images, the wrinkling parameters were measured as a function of the thickness of NR film from 0.42 to 1.76 mm. Also, it was evaluated that the effects of swelling time on the wrinkling parameters. The length (L), distance (D) and height (H) of wrinkles increased as the thickness of the NR film and the swelling time increased. However, the angle between the wrinkles (${\theta}$) showed a sharp decrease up to a swelling time of 200 minutes and slightly decreased afterwards.

• Tribology and Lubricants
• /
• v.22 no.4
• /
• pp.182-189
• /
• 2006

In this paper, the adhesion characteristics between a fused silica without or with an anti-sticking layer and a thermoplastic polymer film used in thermal NIL were investigated experimentally in order to identify the release performance of the anti-sticking layer. The anti-sticking layers were derived from fluoroalkylsilanes, (1H, 1 H, 2H, 2H-perfluorooctyl)trichlorosilane ($F_{13}-OTS$) and (3, 3, 3-trifluoropropyl)trichlorosilane (FPTS), and coated on the silica surface in vapor phase. The commercial polymers, mr-I 7020 and 8020 (micro resist technology, GmbH), for thermal NIL were spin-coated on Si substrate with a rectangular island which was fabricated by conventional microfabrication process to achieve small contact area and easy alignment of flat contact sur- faces. Experimental conditions were similar to the process conditions of thermal NIL. When the polymer film on the island was separated from the silica surface after imprint process, the adhesion force between the silica surface and the polymer film was measured and the surfaces of the silica and the polymer film after the separation were observed. As a result, the anti-sticking layers remarkably reduced the adhesion force and the surface damage of polymer film and the chain length of silane affects the adhesion characteristics. The anti-sticking layers derived from FPTS and $F_{13}-OTS$ reduced the adhesion force per unit area to 38% and 16% of the silica sur-faces without an anti-sticking layer, respectively. The anti-sticking layer derived from $F_{13}-OTS$ was more effective to reduce the adhesion, while both of the anti-sticking layers prevented the surface damages of the polymer film. Finally, it is also found that the adhesion characteristics of mr-I 7020 and mr-I 8020 polymer films were similar with each other.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.1086-1089
• /
• 2003

We investigated the electro-optical (EO) performances of the super twisted nematic liquid crystal display (STN-LCD) on the polyimide (PI) surface using polymer film. Monodomain alignment of the plastic STN-LCD can be observed. A stable voltage-transmittance (V-T) curve of the plastic STN-LCD was observed on the polyimide (PI) surfaces using polymer film. Also, a faster response time for the plastic STN-LCD on the polyimide (PI) surfaces using polymer film can be achieved. Therefore, the EO performances of the plastic STN-LCD on the polyimide (PI) surfaces using polymer film is almost the same as that of the glass STN-LCD on a polyimide (PI) surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.477-480
• /
• 2003

We investigated the electro-optical (EO) performances of the super twisted nematic liquid crystal display (STN-LCD) on the polyimide (PI) surface using polymer film. Monodomain alignment of the plastic STN-LCD can be observed. A stable voltage-transmittance (V-T) curve of the plastic STN-LCD was observed on the polyimide (PI) surfaces using polymer film. Also, a faster response time for the plastic STN-LCD on the polyimide (PI) surfaces using polymer film can be achieved. However, the transmittance of the plastic STN-LCD on the polyimide (PI) surfaces using polymer film decreased greatly as cell gap decreases.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.504-505
• /
• 2005

In this report, we demonstrate a high performance polymer thin-film transistor fabricated on a paper substrate. As a water barrier layer, parylene was coated on the paper substrate by using vacuum deposition process. Using poly (3-hexylthiophene) as an active layer, a polymer thin-film transistor with field-effect of up to 0.086 $cm^2/V{\cdot}s$ and on/off ratio of $10^4$ was achieved. The fabrication of polymer thin-film transistor built on a cheap paper substrate is expected to open a channel for future applications in flexible and disposable electronics with extremely low-cost.

• Analytical Science and Technology
• /
• v.7 no.2
• /
• pp.181-186
• /
• 1994

Using poly(3-methylthiophene) conducting polymer film electrodes, feasiblity for Ag determination by stripping voltammetry has been studied. Ag ions accumulated by complexation with 18-crown-6, which are existing on the surface of the polymer film electrode, migrate inside of polymer film through potential scanning within limited potential range, and then are reduced and oxidized on the glassy carbon substrate. Therefore, the polymer film must have proper thickness and porosity for easy penetration of Ag ions. On the basis of these experimental results, $5.0{\times}10^{-6}M$ Ag(I) in aqueous solution could be determined.

• Journal of Adhesion and Interface
• /
• v.6 no.1
• /
• pp.7-10
• /
• 2005

Condensation control of nano-particles has become important in order to fabricate minute condensed structures. In this study, we focus our attention on condensation mechanism of polymer aggregates in a resist film. The polymer aggregate is structural component of a resist material which is used in lithography process. The condensation nature of polymer aggregates in the resist film surface is observed by using atomic force microscope (AFM). By using the AFM, the condensation of polymer aggregates can be observed clearly. The condensation of polymer aggregate strongly affects to precise fabrication of resist pattern below 100nm size. The interaction force among polymer aggregates can be analyzed based on Derjaguin approximation. We also discuss about condensation nature of polymer aggregates in the resist film surface with the help of micro sphere model.

• Macromolecular Research
• /
• v.9 no.1
• /
• pp.1-19
• /
• 2001

Poly(p-phenylene pyromellitimide) and poly(4,4'-biphenylene pyromellitimide) are representatives of fully rod-like polyimides. Their structure and properties in thin films are reviewed. The polymers exhibit some excellent properties such as high molecular packing coefficient, high mechanical modulus, and low thermal expansion coefficient, and low interfacial stress, so that they are very attractive to both industry and academia. However, these polymers are very brittle and thus practically useless. Some chemical modifications to improve such drawback with a little sacrifice of the high modulus are described: i) incorporation of short side groups into the polymer backbone and ii) insertion of proper linkages into the polymer backbone.

• Polymer(Korea)
• /
• v.28 no.6
• /
• pp.545-550
• /
• 2004

The refractive index of thin copolymer film was controlled by photo-degradation of chromophores in the copolymer. FTIR and UV/Vis spectroscopy were employed to elucidate the effect of chemical structure on refractive index changes after photobleaching. The decrease of refractive index of the film by photobleaching can be ascribed to the decrease of polarizability of polymer molecules through breakage of C =C bond in the chromophore. Due to the selective photoreaction of the chromophores which align along the film plane, refractive index of the copolymer film measured in TE mode decreases faster than that in TM mode. Polarized ATR-FTIR spectroscopy was used to verify such a difference in refractive index of the film.

• Polymer Science and Technology
• /
• v.3 no.3
• /
• pp.185-206
• /
• 1992