• 수산해양기술연구
• /
• 제44권3호
• /
• pp.250-256
• /
• 2008

Generally the side plate materials of FRP ship are composed of glass fiber and unsaturated polyester resin composites(GFRP composites). In this study, the effect of applied load and sliding speed on friction and wear characteristics of these materials were investigated at ambient temperature by pin-on-disc friction test. The cumulative wear volume, friction coefficient and wear rate of these materials for SiC abrasive paper were determined experimentally. The cumulative wear volume showed a tendency to increase nonlinearly with increase of sliding distance and was dependent on applied load and sliding speed for these composites. The friction coefficient of GFRP composites was increased as applied load increased at same sliding speed in wear test. It was verified by SEM photograph of worn surface that major failure mechanisms were microfracture, deformation of resin, cutting and cracking.

• Macromolecular Research
• /
• 제13권1호
• /
• pp.19-29
• /
• 2005

Polymer composites based on a thermotropic liquid-crystalline polymer (TLCP) and poly(butylene terephthalate) (PBT) were prepared using a melt blending process. Polymer composites consisting of bulk cheap polyester with a small quantity of expensive TLCP are of interest from a commercial perspective. The interactions between the PBT chains and the flexible poly(ethylene terephthalate) (PET) units in the TLCP phase resulted in an improvement in the compatibility of PBT/TLCP composites. TLCP droplets deformed and fragmented into smaller droplets in the PBT/TLCP composites, which resulted in TLCP fibrillation through the effective deformation of the TLCP droplets. The nucleation activities of the PBT/TLCP composites increased by adding even a small amount of the TLCP component.

• Composites Research
• /
• 제26권2호
• /
• pp.141-145
• /
• 2013

본 연구에서는 CFRP 적층판에 다양한 종류의 부직포를 삽입하여 모드 II 층간파괴인성을 평가하고, 파단면의 SEM 분석을 통해 층간파괴인성의 증가 원인을 파악하였다. 모드 II 층간파괴인성값($J/m^2$)은 ENF실험에 의하여 얻어졌으며, 부직포를 삽입하지 않은 시편과 3종류의 부직포(8 $g/m^2$의 탄소부직포, 10 $g/m^2$의 유리부직포, 8 $g/m^2$의 폴리에스테르부직포)가 각각 삽입된 시험편들이 준비되었다. 각 시험편들에 대한 모드 II 층간파괴인성값은 부직포를 삽입하지 않은 시편을 기준으로 탄소부직포를 삽입한 시편은 197.7% 증가하였고, 유리부직포를 삽입한 시편은 약 135.4% 증가하였으며, 폴리에스테르부직포를 삽입한 시편은 약 158.7% 증가하였다. 부직포 삽입에 의한 모드 II 층간파괴인성값의 증가 원인은 SEM 분석에 의한 결과 단섬유의 섬유가교(Fiber bridging), 섬유파단(Fiber breakage), 헥클(Hackle) 등의 발생에 기인된 것으로 확인되었다.

• Advances in materials Research
• /
• 제6권4호
• /
• pp.329-341
• /
• 2017

The challenge of replacing conventional plastics with biodegradable composite materials has attracted much attention in product design, particularly in the tensile-related areas of application. In this study, fibres extracted from oil palm empty fruit bunch (EFB) were treated and utilized in reinforcing polyester matrix by hand lay-up technique. The effect of fibre loading and combined influence of alkali and silane treatments on porosity and water absorption parameters, and its correlation with the tensile behaviour of composites was analyzed. The results showed that tensile strength decreased whilst modulus of elasticity, water absorption and porosity parameters increased with increasing fibre loading. The composites of treated oil palm EFB fibre exhibited improved values of 2.47 MPa to 3.78 MPa for tensile strength; 1.75 MPa to 2.04 MPa for modulus of elasticity; 3.43% to 1.68% for porosity and 3.51% to 3.12% for water absorption at respective 10 wt.% fibre loadings. A correlation between porosity and water absorption with tensile behavior of composites of oil palm EFB fibre and positive effect of fibre treatment was established, which clearly demonstrate a connection between processing and physical properties with tensile behavior of fibre composites. Accordingly, a further exploitation of economic significance of oil palm EFB fibres composites in areas of low-to-medium tensile strength application is inferred.

• Composites Research
• /
• 제36권1호
• /
• pp.37-41
• /
• 2023

선박의 평형수처리장치 전해조 내부 용액은 해수를 전기분해 시 DSA(Dimension Stable Anode) 전극에서 생성되는 수산화물로 인하여 높은 알칼리성 분위기를 생성한다. 본 연구에서는 기존 평형수처리장치 배관에 사용되어지는 PE 코팅 강관 배관의 취약성을 대체 가능한 복합재료로써 4가지 소재를 선정하였으며, 이들 BRE(Basalt fiber reinforced epoxy), BRP(Basalt fiber reinforced unsaturated polyester), GRE(Glass fiber reinforced epoxy), GRP(Glass fiber reinforced unsaturated polyester)를 강 알칼리성 NaOH 용액에 720시간 침지 후 마찰 및 마모 시험을 통하여 재료 마찰 깊이에 따른 마찰계수와 섬유와 수지 간 계면 결합 거동을 분석하였다. 그 결과, 수지와 섬유 간의 게면 분리 현상에 대한 메커니즘을 도출하였다. 또한, 불포화폴리에스테르와 같이 상대적으로 낮은 계면 결합력의 갖는 소재의 경우, 알칼리성 용액에 침지 시간이 길어질수록 표면에서부터 시작된 열화가 내부로 급격하게 확산되어 마찰 계수의 감소로 이어지는 경향을 나타냈다.

• Elastomers and Composites
• /
• 제48권3호
• /
• pp.190-194
• /
• 2013

본 연구에서는 피마자유 유래의 sebacic acid를 isophthalic acid 및 glycol과 병용하여 폴리에스터 폴리올을 중합하고 이어서 폴리우레탄 접착제를 제조하였다. 접착력을 측정한 결과에서 sebacic acid를 병용한 폴리올이 adipic acid를 사용한 폴리올 보다 응집에너지가 커서 접착력이 우수하게 나타났고, glycol은 선형구조 보다 메틸기를 포함하는 가지구조가 더 좋은 접착력을 보였다. 쇄연장제는 1,4-butane diol(BD)를 사용한 것이 가장 접착력이 좋게 나타났다. 또한 TGA 측정결과 내열성은 BD가 가장 높고, 1,2-propylene glycol(PG)가 다음, ethylene glycol(EG)가 가장 낮았다. DMA 측정에서 유리전이온도는 PG, EG, BD의 순서로 높게 나타났다.

• 한국안전학회지
• /
• 제16권1호
• /
• pp.88-93
• /
• 2001

본 연구에서는 복합소재인 GFRP(Glass Fiber Reinforced Polyester)의 2차원 절삭공정에서 절삭 메커니즘과 소재의 신뢰도 및 안전성과 밀접한 관련이 있는 표면정도를 중심으로 한 공정의 특성화를 시도하고, 주파수 분석에 관하여도 논의한다. 구체적으로는, 공정중 발생하는 절삭력 신호를 AR(Autoregressive) 모델링하여 해석에 사용한다. 특히, 특징추출과정을 통해 AR계수로 이루어진 패턴벡터 중 다양한 절삭 메카니즘에 민감한 계수만 선택할 수 있다. 이들 계수와 절삭 메커니즘과의 실험적 관계를 설정함으로써 섬유경사각(Fiber orientation angle), 절삭 변수 그리고 공구형상이 절삭 메커니즘에 미치는 영향을 평가하였다.

• Steel and Composite Structures
• /
• 제18권5호
• /
• pp.1291-1303
• /
• 2015

Damage caused by low velocity impact is so dangerous in composites because although in most cases it is not visible to the eye, it can greatly reduce the strength of the composite material. In this paper, damage development in U-section glass/polyester pultruded beams subjected to low velocity impact was considered. Different failure criteria such as Maximum stress, Maximum strain, Hou, Hashin and the combination of Maximum strain criteria for fiber failure and Hou criteria for matrix failure were programmed and implemented in ABAQUS software via a user subroutine VUMAT. A suitable degradation model was also considered for reducing material constants due to damage. Experimental tests, which performed to validate numerical results, showed that Hashin and Hou failure criteria have better accuracy in predicting force-time history than the other three criteria. However, maximum stress and Hashin failure criteria had the best prediction for damage area, in comparison with the other three criteria. Finally in order to compare numerical model with the experimental results in terms of extent of damage, bending test was performed after impact and the behavior of the beam was considered.

• Elastomers and Composites
• /
• 제37권3호
• /
• pp.192-194
• /
• 2002

Polyester cord yarns have been treated in an atmospheric-pressure nitrogen plasma reactor in order to enhance their adhesion to rubber. A thin layer or the plasma was generated in the close vicinity of the yam surface using various types or surface discharge. To assess the effect of the plasma treatment on fiber surface properties, the cord thread/rubber matrix adhesion values measured using the untreated and threads cord threads were compared. The static and dynamic adhesion of the cord thread to rubber was characterized by using the standard Henley test. The dynamic adhesion values for the reference and plasma treated fiber were $7,3{\pm}1,2\;N$ and $83,5{\pm}3,5\;N$. The surface properties were investigated by scanning electron microscopy, infrared spectroscopy and electron spin resonance spectroscopy. It is concluded that both polar group interactions and increased surface area of the fibers are responsible for the improved adhesive strength.

• Elastomers and Composites
• /
• 제52권1호
• /
• pp.81-85
• /
• 2017

In order to improve the water resistance, we synthesized waterborne polyurethane by using polyester polyol, poly(propylene carbonate) (PPC), 4,4'-dicyclohexylmethane diisocyanate ($H_{12}MDI$), and dimethylolpropionic acid (DMPA). The properties of the synthesized waterborne polyurethane using poly(propylene carbonate) (WPUP) were evaluated by FT-IR, $^1H-NMR$, GPC, DSC, TGA, and UTM. The mechanical properties increased while the adhesion properties decreased with the increase in the amount of PPC. The highest water resistance was shown when the ratio of polyester polyol to PPC was 9:1.