• 한국세라믹학회지
• /
• 제48권3호
• /
• pp.251-256
• /
• 2011

The luminescence properties of polycrystalline ZnO annealed in reducing ambience ($H_2/N_2$) have been studied. An effective quenching of green luminescence with enhanced UV emission from polycrystalline ZnO is observed for the reduced ZnO. The variations of the UV and green luminescence band upon reduction treatment are investigated as a function of temperature in the range between 20 and 300 K. Upon annealing treatment in reducing ambience, the optical quality of polycrystalline ZnO is improved. The UV to green intensity ratio of sintered ZnO approaches close to zero (~0.05). However, this ratio reaches more than 13 at room temperature for polycrystalline ZnO annealed at $800^{\circ}C$ in reducing ambience. Furthermore, the full width at half maximum (FWHM) of the UV band of polycrystalline ZnO is reduced compared to unannealed polycrystalline ZnO. Electron paramagnetic resonance (EPR) measurements clearly show that there is no direct correlation between the green luminescence and oxygen vacancy concentration for reduced polycrystalline ZnO.

• 한국재료학회지
• /
• 제8권7호
• /
• pp.579-583
• /
• 1998

P가 고농도로 도핑된 다결정 Si 기판 위에 Co/Ti 이중층막을 스퍼터 증착하고 급속열처리함으로써 얻어지는 실리사이드 층구조, 실리사이드막의 응집, 그리고 도펀트의 재분포 등을 단결정 Si 기판 위에서의 그것들과 비교하여 조사하였다. 다결정 Si 기판위에 형성한 Co/Si 이중층을 열처리할 때 단결정 기판에서의 경우보다 $CoSi_2$로의 상천이는 약간 더 낮은 온도에서 시작되며, 막의 응집은 더 심하게 일어난다. 또한, 다결정 Si 기판내의 도펀트보다 웨이퍼 표면을 통하여 바깥으로 outdiffusion 함으로써 소실되는 양이 훨씬 더 많다. 이러한 차이는 다결정 Si 내에서의 결정립계 확산과 고농도의 도펀트에 기인한다. Co/Ti/doped-polycrystalline si의 실리사이드화 열처리후의 층구조는 polycrystalline CoSi2/polycrystalline Si 으로서 Co/Ti(100)Si을 열처리한 경우의 층구조인 Co-Ti-Si/epi-CoSi2/(100)Si 과는 달리 Co-Ti-Si층이 사라진다.

• 산업기술연구
• /
• 제2권
• /
• pp.13-19
• /
• 1982

Polycrystalline silicon layers have been deposited by a chemical vapor deposition technique using $SiCl_4$, $H_2$ gas mixture on single crystal silicon substrates. In this work, the effects of depostion temperature and total flow rate on the deposition rate of polycrystalline silicon are investigated. From the experimental results it was found that the formation reaction of polycrystalline silicon was limited by surface reaction and mass transfer controlled as the deposition temperature was increased. The morphology of polycrystalline silicon layer changed from a fine structure to a coarse one as the deposition temperature was increased.

• 한국정밀공학회지
• /
• 제22권12호
• /
• pp.170-174
• /
• 2005

A numerical system to extract effective elastic properties of polycrystalline thin-films for MEMS devices is developed. In this system, the statistical model based on lattice system is used for modeling the microstructure evolution simulation and the key kinetics parameters of given micrograph, grain distributions and deposition process can be extracted by inverse method proposed in the system. In this work, effects of kinetics parameters on the extraction of effective elastic properties of polycrystalline thin-films are studied by using statistical method. Effects of the fraction of the potential site($f_p$) among the parameters for deposition process of microstructure on the extraction of effective elastic properties of polycrystalline thin-films are investigated. For this research, polysilicon is applied to this system as the polycrystalline thin-films.

• 한국세라믹학회지
• /
• 제36권6호
• /
• pp.604-610
• /
• 1999

Silicide layer structures and morphology degradation of the surface and interface of the silicide layers for he Co/refractory metal bilayer sputter-deposited on the P-doped polycrystalline Si substrate and subjected to rapid thermal annealing were investigated and compared with those on the single Si substrate. The CoSi-CoSi2 phase transition temperature is lower an morphology degradation of the silcide layer occurs more severely for the Co/refractorymetal bilayer on the P-doped polycrystalline Si substrate than on the single Si substrate. Also the final layer structure and the morphology of the films after silicidation annealing was found to depend strongly upon the interlayer metal. The layer structure after silicidation annealing of Co/Hf/doped-poly Si is Co-Hf alloy/polycrystalline CoSi2/poly Si substrate while that of Co/Nb is polycrystalline CoSi2/NbSi2/polycrystalline CoSi2/poly Si.

• 한국전기전자재료학회논문지
• /
• 제22권4호
• /
• pp.303-306
• /
• 2009

This paper describes the characteristics of polycrystalline 3C-SiC doubly clamped beam micro resonators. The polycrystalline 3C-SiC doubly clamped beam resonators with $60{\sim}100{\mu}m$ lengths, $10{\mu}m$ width, and $0.4{\mu}m$ thickness were fabricated using a surface micromachining technique. Polycrystalline 3C-SiC micro resonators were actuated by piezoelectric element and their fundamental resonant frequency was measured by a laser vibrometer in vacuum at room temperature. For the $60{\sim}100{\mu}m$ long cantilevers, the fundamental frequency appeared at $373.4{\sim}908.1\;kHz$. The resonant frequencies of doubly clamped beam with lengths were higher than simulated results because of tensile stress. Therefore, polycrystalline 3C-SiC doubly clamped beam micro resonators are suitable for RF MEMS devices and bio/chemical sensor applications.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.250-250
• /
• 2008

This paper describes the resonant characteristics of polycrystalline SiC micro resonators. The $1{\mu}m$ thick polycrystalline 3C-SiC cantilevers with different lengths were fabricated using a surface micromachining technique. Polycrystalline 3C-SiC micro resonators were actuated by piezoelectric element and their fundamental resonance was measured by a laser vibrometer in vacuum at room temperature. For the 100 ~ $40{\mu}m$ long cantilevers, the fundamental frequency appeared at 147.2 kHz - 856.3 kHz. The $100{\mu}m$ and $80{\mu}m$ long cantilevers have second mode resonant frequency at 857.5 kHz and 1.14 MHz. Therefore, polycrystalline 3C-SiC micro resonators are suitable for RF MEMS devices and bio/chemical sensor applications.

• 센서학회지
• /
• 제17권6호
• /
• pp.425-428
• /
• 2008

This paper describes the resonant characteristics of polycrystalline SiC micro resonators. The $1{\mu}m$ thick polycrystalline 3C-SiC cantilevers with different lengths were fabricated using a surface micromachining technique. Polycrystalline 3C-SiC micro resonators were actuated by piezoelectric element and their fundamental resonance was measured by a laser vibrometer in vacuum at room temperature. For the $100{\sim}40{\mu}m$ long cantilevers, the fundamental frequency appeared at $147.2kHz{\sim}856.3kHz$. The $100{\mu}m$ and $80{\mu}m$ long cantilevers have second mode resonant frequency at 857.5.kHz and 1.14.MHz, respectively. Therefore, polycrystalline 3C-SiC resonators are suitable for RF MEMS devices and bio/chemical sensor applications.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.217-217
• /
• 2009

This paper describes the characteristics of polycrystalline 3C-SiC doubly clamped beam micro resonators. The polycrystalline 3C-SiC doubly clamped beam resonators with 60 ~ 100 ${\mu}m$ lengths, $10\;{\mu}m$ width, and $0.4\;{\mu}m$ thickness were fabricated using a surface micromachining technique. Polycrystalline 3C-SiC micro resonators were actuated by piezoelectric element and their fundamental resonant frequency was measured by a laser vibrometer in vacuum at room temperature. For the 60 ~ 100 ${\mu}m$ long cantilevers, the fundamental frequency appeared at 373.4 ~ 908.1 kHz. The resonant frequencies of doubly clamped beam with lengths were higher than simulated results because of tensile stress. Therefore, polycrystalline 3C-SiC doubly clamped beam micro resonators are suitable for RF MEMS devices and bio/chemical sensor applications.

• 대한기계학회논문집A
• /
• 제21권8호
• /
• pp.1291-1297
• /
• 1997

Elastic-plastic finite element(FE) simulation was performed for polycrystalline solids subjected to plane strain tensile loading. Using Asaro's double slip crystal plasticity model, the polycrystalline solids were modeled by assigning different initial slip directions to each grain. From the FE calculations, the microscopic deformation characteristics of polycrystalline solids were analyzed. Moreover, the effect of grain size and grain boundaries on the deformation characteristics were clarified.